NISSAN X-TRAIL 2005 Service Repair Manual

DOOR OUTSIDE LOWER MOLDING
EI-25
C
D
E
F
G
H
J
K
L
MA
B
EI

DOOR OUTSIDE LOWER MOLDINGPFP:82877
Removal and InstallationEIS000N4
REMOVAL
Door outside molding (front/rear)
1. Remove clips of door outside molding.
2. Remove door outside molding (front/rear).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When installing door outside molding, make sure that blind clips are securely fitted in panel hole on
body and then press them in.
1. Door outside lower molding (front door) 2. Door outside lower molding (rear door)
SIIA0206E

EI-26
SIDE SILL PROTECTOR

SIDE SILL PROTECTORPFP:86856
Removal and InstallationEIS000N5
REMOVAL
1. Remove screw and clip of side sill protector.
2. Remove side sill protector.
INSTALLATION
Installation is in the reverse order of removal.
SIIA0207E

ROOF RAIL
EI-27
C
D
E
F
G
H
J
K
L
MA
B
EI

ROOF RAILPFP:73820
Removal and Installation (for Hyper Roof Rail)EIS000N6
CAUTION:
Be careful not to damage the body.
REMOVAL
1. Remove driving lamp cap (front).
2. Remove driving lamp mounting nuts.
3. Pull driving lamp upward to disconnect clips of driving lamp from roof panel.
4. Disconnect driving lamp harness connector.
5. Remove driving lamp assembly.
6. Remove hyper roof rail caps (front and rear).
7. Remove side rail mounting bolts and nuts, then remove side rail.
8. Remove rear spoiler mounting bolts, then remove rear spoiler.
9. Remove hyper roof rail mounting nuts, then remove hyper roof rail assembly.
10. Remove headlining. Refer to EI-39, "
HEADLINING" .
11. Remove driving lamp bracket, hyper roof rail bracket (front and rear) and roof spoiler bracket.
INSTALLATION
Installation is in the reverse order of removal.
1. Roof rail 2. Rear spoiler 3. Hyper roof rail rear cap
4. Rear spoiler bracket 5. Hyper roof rail center bracket (rear) 6. Hyper roof rail center bracket (front)
7. Hyper roof rail bracket (rear) 8. Hyper roof rail bracket (front) 9. Hyper roof rail front cap
10. Side rail 11. Driving lamp cap (rear) 12. Driving lamp assembly
13. Driving lamp cap (front) 14. Driving lamp bracket
PIIA6946E

EI-28
ROOF RAIL

Removal and Installation (for Roof Rail)EIS008OQ
CAUTION:
Be careful not to damage the body.
REMOVAL
1. Remove headlining. Refer to EI-35, "BODY SIDE TRIM" .
2. Remove roof rail mounting nuts and roof rail covers (or roof
spoiler) mounting nuts.
1. Roof rail 2. Front cap 3. Rear cap
4. Roof rail cover 5. Roof rail bracket (front) 6. Roof rail bracket (rear)
SIIA0265E
SIIA0214E

ROOF RAIL
EI-29
C
D
E
F
G
H
J
K
L
MA
B
EI

3. Remove roof rail bracket mounting nuts (front and rear).
4. Remove roof rail covers (or roof spoiler). For removal of roof spoiler, refer to EI-30, "
ROOF SPOILER" .
5. Remove roof rail mounting clips, and remove roof rails.
INSTALLATION
Installation is in the reverse order of removal.
SIIA0215E

EI-30
ROOF SPOILER

ROOF SPOILERPFP:96030
Removal and InstallationEIS000N7
CAUTION:
Be careful not to damage the body.
REMOVAL
1. Remove headlining. Refer to EI-39, "Removal and Installation" .
2. Remove covers (left and right).
3. Remove roof spoiler mounting nuts (upper and lower roof surfaces).
4. Pull roof spoiler upwards. Remove tabs (1 each on left/right) which are engaged with the roof rails.
Remove roof spoiler.
INSTALLATION
Installation is in the reverse order of removal.
1. Cover (left) 2. Cover (right) 3. Roof spoiler
SIIA0216E

LICENSE LAMP FINISHER
EI-31
C
D
E
F
G
H
J
K
L
MA
B
EI

LICENSE LAMP FINISHERPFP:84810
Removal and InstallationEIS001NV
REMOVAL
1. Remove back door finisher. Refer to EI-34, "Removal and Installation" .
2. Remove license plate lamp. Refer to LT- 1 0 7 , "
LICENSE PLATE LAMP" .
3. Remove license lamp finisher mounting nuts and clips and then remove finisher.
INSTALLATION
Installation is in the reverse order of removal.
1. License lamp finisher
SIIA0220E

EI-32
DOOR FINISHER

DOOR FINISHERPFP:80900
Removal and InstallationEIS000N9
FRONT AND REAR
Removal
1. Insert a screwdriver, wrapped with a cloth, into door trim cutout
on the inside handle escutcheon. Disengage the pawls on the
front, upper side (2) and lower side (2). Slide rearwards and dis-
engage the rear-side pawls to remove.
SIIA0203E
1. Front door finisher 2. Inside handle escutcheon 3. Front door armrest
4. Rear door finisher 5. Inside handle escutcheon 6. Rear door armrest
SIIA0391E

DOOR FINISHER
EI-33
C
D
E
F
G
H
J
K
L
MA
B
EI

2. Insert a screwdriver, wrapped with a cloth, into the cutout on the
front edge of power window switch finisher. Unfasten the metal
clip on the front side.
3. Insert the screwdriver into the gap and remove metal clips, mov-
ing from front to rear.
4. Disconnect and remove power window switch connector.
5. Remove door finisher mounting screw.
6. Insert a screwdriver, wrapped with a cloth, into the cutout on the
lower part of door finisher. Unfasten the clips.
CAUTION:

Insert a clip driver or clip clamp remover into the part
shown by the arrow (between the body side panel and the
clips). Remove finisher.

To install the finisher, confirm clips are surely aligned with
the holes on the body side panel, then press in.
7. Pull the door finisher upwards to remove.
Installation
Installation is in the reverse order of removal.
SIIA0208J
SIIA0211J
SIIA0213J
SIIA0810E

EI-34
BACK DOOR TRIM

BACK DOOR TRIMPFP:90900
Removal and InstallationEIS000NA
REMOVAL
1. Remove clips of back door trim.
2. Remove back door trim.
CAUTION:

Insert a clip driver or clip clamp remover into the part
shown by the arrow (between the clips and the body side
panel). Remove clips.

When installing, confirm clips are surely aligned with the
holes on the body side panel, then press in.
INSTALLATION
Installation is in the reverse order of removal.
SIIA0221E
PIIA0527E