light OLDSMOBILE INTRIGUE 1998 Service Manual
Page 153 of 340
Care of Your Cassette  Tape Player 
A tape player  that  is  not cleaned  regularly can  cause 
reduced  sound quality, ruined  cassettes  or  a damaged 
mechanism.  Cassette tapes should  be stored in their 
cases  away from  contaminants,  direct  sunlight and 
extreme  heat. If they aren’t, they  may not operate 
properly 
or may  cause  failure  of the tape player. 
Your  tape  player  should be cleaned regularly  after  every 
50 hours of use.  Your  radio  may display  CLN  to  indicate 
that  you have used your  tape player  for 
50 hours without 
resetting  the  tape  clean  timer. If this  message appears on 
the  display, your  cassette  tape  player  needs to be 
cleaned.  It will still play  tapes,  but you should  clean it as 
soon as  possible  to prevent damage to your  tapes and 
player.  If  you notice  a reduction in sound quality,  try a 
known good  cassette  to 
see if it is the tape or the tape 
player  at fault.  If this  other  cassette  has no improvement 
in sound quality,  clean the tape  player. 
The  recommended  cleaning method for your  cassette 
tape  player  is the use  of a  scrubbing  action, 
non-abrasive  cleaning  cassette  with pads which scrub 
the tape head  as the hubs  of the  cleaner  cassette  turn. 
The  recommended  cleaning  cassette  is available  through 
your retail  facility 
(GM Part No. 12344789). 
When using  a scrubbing  action,  non-abrasive  cleaning 
cassette,  it  is normal for the  cassette  to  eject  because 
your unit  is equipped with 
a cut  tape  detection  feature 
and  a  cleaning  cassette  may appear  as a broken tape. 
If 
the  cleaning  cassette  ejects,  insert the cassette at least 
three  times  to  ensure  thorough cleaning. 
You  may  also choose  a non-scrubbing  action, wet-type 
cleaner  which uses  a  cassette with a  fabric  belt to  clean 
the tape  head.  This  type of cleaning  cassette will not 
eject on 
its own. A non-scrubbing  action  cleaner may 
not clean as thoroughly 
as the  scrubbing  type cleaner. 
The  use  of a non-scrubbing  action,  dry-type  cleaning 
cassette 
is not recommended. 
After  you clean the player, press and hold  EJECT  for 
five  seconds 
to reset  the  CLN  indicator.  The radio will 
display 
--- to  show  the  indicator  was reset. 
Cassettes 
are subject to wear and  the sound quality 
may  degrade  over  time.  Always make  sure  the cassette 
tape  is in  good condition  before you have your tape 
player serviced. 
3-27 
ProCarManuals.com 
Page 154 of 340
Care of Your Compact  Discs 
Handle discs carefully. Store them  in their original cases 
or  other protective cases and away from direct sunlight 
and  dust.  If the surface  of a disc  is soiled, dampen  a 
clean,  soft cloth  in a  mild,  neutral detergent solution and 
clean 
it, wiping from the  center  to the edge. 
Be  sure  never to touch the signal  surface when handling 
discs.  Pick up discs  by grasping the outer edges  or the 
edge 
of the hole and the outer edge. 
Care  of  Your  Compact  Disc  Player 
The  use of CD lens cleaner  discs is not advised, due to 
the risk  of contaminating  the lens 
of the CD optics  with 
lubricants internal to the 
CD mechanism. 
Backglass  Antenna (If Equipped) 
Your  AM-FM  antenna is integrated with your  rear 
window defogger, located in the  rear window.  Be sure 
that the inside surface  of the rear window 
is not 
scratched and that the lines on  the glass are not 
damaged. 
If the inside surface is damaged, it  could 
interfere with  radio reception. 
NOTICE: 
Do not  try  to  clear  frost  or  other  material  from 
the  inside  of  the  rear  window  with  a 
razor blade 
or  anything  else  that  is  sharp.  This  may  damage 
the  rear  defogger  grid  and  affect  your  radio’s 
ability  to  pick  up  stations  clearly.  The  repairs 
wouldn’t  be  covered  by  your  warranty. 
Because this antenna  is built into your  rear  window, 
there  is a reduced risk  of damage caused  by car washes 
and  vandals. 
If you  choose  to add  a cellular telephone  to  your vehicle, 
and  the  antenna needs to  be attached 
to the glass,  be sure 
that 
you do  not  damage the grid lines  for the  AM-FM 
antenna. There is enough space between the lines  to 
attach  a cellular telephone antenna without interfering 
with  radio reception. 
3-28 
ProCarManuals.com 
Page 161 of 340
Avoid needless  heavy braking.  Some  people  drive  in 
spurts 
-- heavy  acceleration  followed by heavy braking 
-- rather  than keeping pace with traffic.  This is a 
mistake. Your brakes  may not have  time to cool between 
hard  stops.  Your brakes  will wear  out much  faster if 
you  do a  lot  of heavy braking.  If you keep pace  with the 
traffic and allow realistic  following  distances, you will 
eliminate  a  lot  of unnecessary  braking.  That  means 
better braking and  longer brake  life. 
If  your  engine  ever  stops while  you’re  driving,  brake 
normally  but don’t  pump  your brakes. 
If you do, the 
pedal  may get  harder  to  push down. If your  engine 
stops,  you will  still have  some  power  brake  assist.  But 
you will  use it when you  brake.  Once  the  power assist is 
used  up, it may  take longer  to 
stop and the brake pedal 
will  be  harder 
to push. 
Anti-Lock Brakes (ABS) 
Your vehicle has anti-lock  brakes  (ABS). ABS is an 
advanced  electronic  braking  system that will  help 
prevent  a  braking skid. 
When  you  start your engine,  or  when you begin to  drive 
away, your  anti-lock brake system  will check itself.  You 
may  hear 
a momentary motor  or  clicking noise while 
this  test  is  going on, and you  may even  notice  that your 
brake pedal moves  or pulses  a  little.  This  is normal. 
ANTI - 
LOCK 
If  there’s  a problem with 
the anti-lock  brake  system, 
this warning light will stay 
on  or  flash.  See “Anti-Lock 
Brake System Warning 
Light”  in the Index. 
4-7 
ProCarManuals.com 
Page 163 of 340
Remember: Anti-lock  doesn’t  change the time you need 
to  get  your foot up to  the  brake  pedal  or  always decrease 
stopping  distance.  If 
you get  too  close  to  the  vehicle  in 
front 
of you,  you won’t have  time  to apply your  brakes 
if  that  vehicle  suddenly  slows  or stops. Always  leave 
enough room up ahead  to  stop, even though  you have 
anti-lock  brakes. 
Using Anti-Lock 
Don’t pump the brakes.  Just hold  the brake pedal down 
firmly  and let  anti-lock  work for  you.  You may  feel  a 
slight  brake  pedal pulsation  or  notice some noise,  but 
this is  normal. 
LOW 
TRAC 
When your  anti-lock system 
is  adjusting  brake  pressure 
to  help  avoid  a  braking  skid, 
this  light  will come  on.  See 
“Low  Traction  Light” in 
the  Index. 
Enhanced  Traction  System (If Equipped) 
Your  vehicle is equipped with an Enhanced Traction 
System (ETS)  that  limits wheel spin.  This  is  especially 
useful  in slippery road  conditions.  The system operates 
only if  it  senses  that one or both  of the  front  wheels are 
spinning  or  beginning  to  lose  traction. When this 
happens,  the system reduces  engine power  and  may 
also  upshift the transaxle  to  limit wheel spin. 
LOW 
TRAC 
This  light  will come  on 
when your Enhanced 
Traction System  is limiting 
wheel  spin. 
See “Low Traction  Light” in the Index. You may feel  or 
hear  the  system working, but this is normal. 
The  Enhanced Traction System  operates in all transaxle 
shift  lever  positions.  But the system can  upshift  the 
transaxle  only as high  as the  shift  lever  position you’ve 
chosen, 
so you should  use the lower gears only when 
necessary.  See “Automatic Transaxle”  in the  Index. 
ProCarManuals.com 
Page 164 of 340
When the system is on, this 
warning  light will come on 
to  let  you know  if there’s a 
problem  with  the  system. 
TRAC 
OFF 
See “Enhanced Traction System Warning  Light’’  in the 
Index.  When this warning  light is on,  the system will not 
limit  wheel spin. Adjust your  driving accordingly. 
To limit wheel spin, especially  in slippery road 
conditions,  you should always  leave the Enhanced 
Traction System on. But you can turn the system  off if 
you  ever  need 
to. (You should  turn the system  off  if your 
vehicle  ever  gets  stuck in  sand,  mud, ice  or  snow.  See 
“Rocking  Your  Vehicle”  in the Index.) 
To turn the system on 
or 
off, press the button 
on  the  console. 
Your  Enhanced Traction System is automatically 
activated when  you turn the ignition  on. This switch 
will  activate/deactivate the Enhanced Traction  System. 
If  you  need to disable the  system, such as when  you 
are  stuck  and are rocking your vehicle back and forth, 
push this switch.  See “Stuck: 
In Sand,  Mud or Snow” 
in  the Index. 
Braking  in Emergencies 
With  anti-lock,  you can steer and brake at the same 
time. In many emergencies, steering can help  you more 
than even the  very best braking. 
4-10 
ProCarManuals.com 
Page 165 of 340
Steering 
Power Steering 
If you  lose  power  steering  assist  because the engine 
stops  or  the  system 
is not functioning,  you can  steer 
but it will  take much more effort. 
Magnetic  Speed  Sensitive  Steering 
This  steering system provides  lighter  steering  effort 
for  parking and when  driving at speeds  below 
20 mph (32 km/h).  Steering  effort will  increase at 
higher  speeds  for  improved road 
feel. 
Steering  Tips 
Driving on Curves 
It’s  important  to  take  curves  at a reasonable  speed. 
A lot of the  “driver lost  control”  accidents  mentioned 
on the news happen on  curves. Here’s why: 
Experienced  driver or beginner, each 
of us is subject  to 
the  same  laws of physics when  driving on curves.  The 
traction 
of the  tires  against  the  road surface  makes it 
possible  for  the vehicle  to change  its path when  you turn 
the  front  wheels. 
If there’s no traction,  inertia will keep 
the  vehicle  going 
in the same  direction.  If you’ve  ever 
tried 
to steer  a vehicle  on wet ice,  you’ll  understand  this. The 
traction  you  can  get in a curve depends  on the 
condition  of 
your tires and the road surface, the angle  at 
which  the curve  is banked,  and  your  speed.  While you’re 
in 
a curve, speed is  the one factor  you can control. 
Suppose you’re steering through a sharp curve. Then  you 
suddenly  accelerate.  Both control systems 
-- steering and 
acceleration 
-- have to  do their work where the tires  meet 
the road. Adding the sudden acceleration  can demand 
too 
much  of those places.  You can lose control. 
What should  you do if this  ever  happens?  Ease up on the 
accelerator pedal,  steer the vehicle the way  you want  it 
to  go,  and slow down. 
Speed limit signs near  curves warn that  you should 
adjust  your speed.  Of course,  the  posted speeds  are 
based on good weather and road  conditions. Under less 
favorable  conditions  you’ll want to 
go slower. 
If you need to  reduce your speed as you approach a 
curve,  do it before  you enter  the  curve,  while  your front 
wheels  are straight  ahead. 
Try 
to adjust  your speed so you can “drive” through the 
curve.  Maintain a  reasonable,  steady speed. Wait 
to 
accelerate  until you are  out  of the  curve,  and then 
accelerate  gently into the straightaway. 
ProCarManuals.com 
Page 167 of 340
Off-Road Recovery 
You may  find that  your right wheels have dropped off the 
edge  of a road  onto the shoulder while you’re driving. 
F*- LEFT APPROX. QUARTERTURN 
Passing 
The  driver  of a vehicle  about  to pass another  on a 
two-lane  highway waits  for  just the right moment, 
accelerates,  moves around the vehicle  ahead, then goes 
back into  the right  lane  again. 
A simple  maneuver? 
Not necessarily!  Passing  another  vehicle  on a two-lane 
highway is a potentially  dangerous move,  since the 
passing vehicle  occupies the same  lane  as oncoming 
traffic  for several  seconds. 
A miscalculation,  an error  in 
judgment,  or  a brief  surrender  to frustration  or  anger can 
suddenly put the  passing  driver  face  to  face  with the 
worst  of all traffic  accidents 
-- the head-on  collision. 
So here  are some tips  for passing: 
0 
If the  level  of the  shoulder  is only slightly below the 
pavement,  recovery should be  fairly easy. Ease off 
the  accelerator  and then,  if there 
is nothing  in  the way, 
steer 
so that your  vehicle straddles the  edge of the 
pavement.  You can turn 
the steering  wheel up to 
one-quarter  turn until the right  front  tire  contacts the 
pavement  edge. Then turn your  steering wheel to go 
straight down  the roadway. 
0 
“Drive ahead.” Look down the road,  to  the  sides 
and to  crossroads  for  situations that might affect 
your passing patterns.  If  you have any doubt 
whatsoever about making a successful pass, wait 
for  a better time. 
Watch  for traffk  signs,  pavement  markings  and  lines. 
If  you  can  see a sign  up  ahead  that  might  indicate  a 
turn or an intersection,  delay  your  pass. A broken 
center  line  usually  indicates  it’s  all  right  to pass 
(providing  the  road  ahead  is  clear).  Never  cross 
a solid 
line  on  your  side  of  the  lane  or 
a double  solid  line, 
even  if the  road  seems  empty 
of approaching  traffic. 
4-13 
ProCarManuals.com 
Page 170 of 340
Driving at Night 
Night driving is more dangerous than day driving. 
One  reason  is that some drivers  are likely  to  be 
impaired 
-- by  alcohol or drugs, with night vision 
problems,  or by fatigue. 
0 
0 
0 
0 
0 
0 
0 
~~~ 
~~ 
Here are some tips on night driving. 
Drive  defensively. 
Don’t drink and drive. 
Adjust your inside rearview mirror to reduce the 
glare  from headlamps behind you. 
Since  you can’t see  as  well, you may  need  to 
slow down and keep more space between you 
and other vehicles. 
Slow down, especially on higher speed roads.  Your 
headlamps  can light  up  only 
so much road ahead. 
In remote areas, watch for animals. 
If  you’re tired, pull 
off the road  in a safe place 
and  rest. 
Night Vision 
No one  can see as well at  night  as in the daytime. But  as 
we  get  older these differences increase. 
A 50-year-old 
driver  may require  at least twice as much light to see the 
same thing  at night  as a 20-year-old. 
What  you do in the daytime can also  affect your night 
vision. For example,  if you spend the day in bright 
sunshine  you are wise to wear sunglasses.  Your eyes will 
ProCarManuals.com 
Page 171 of 340
have  less  trouble  adjusting  to night. But if you’re 
driving,  don’t wear  sunglasses  at  night.  They may cut 
down  on glare  from  headlamps, but they  also  make  a 
lot  of things  invisible. 
You  can be temporarily  blinded by approaching 
headlamps.  It  can  take  a  second or two,  or even  several 
seconds,  for  your eyes to readjust  to  the  dark.  When 
you  are  faced  with severe  glare  (as  from  a  driver 
who  doesn’t  lower  the  high  beams, or  a vehicle with 
misaimed  headlamps),  slow down  a  little.  Avoid 
staring  directly  into  the  approaching  headlamps. 
Keep  your windshield  and all the  glass  on your vehicle 
clean 
-- inside  and out.  Glare  at  night  is  made  much 
worse  by dirt  on the  glass. Even  the  inside of the  glass 
can  build up  a  film caused  by dust.  Dirty  glass  makes 
lights  dazzle  and flash  more  than  clean  glass  would, 
making  the  pupils  of your  eyes  contract  repeatedly. 
Driving in Rain  and on Wet Roads 
Remember  that your headlamps  light  up  far  less of a 
roadway when  you are  in  a  turn or  curve.  Keep  your 
eyes moving;  that way,  it’s  easier  to  pick  out  dimly 
lighted  objects.  Just  as your headlamps should  be 
checked  regularly  for  proper  aim, 
so should your eyes 
be  examined  regularly. Some  drivers  suffer from night 
blindness 
-- the  inability  to see  in  dim  light -- and 
aren’t  even aware 
of it.  Rain 
and  wet  roads can 
mean driving  trouble.  On a wet 
road,  you can’t  stop,  accelerate  or  turn as  well  because 
your  tire-to-road  traction  isn’t  as good as  on dry  roads. 
4-17 
~ 
ProCarManuals.com 
Page 173 of 340
A CAUTION: 
Wet brakes  can  cause  accidents.  They  won’t work 
as well in a quick  stop  and  may  cause  pulling  to 
one  side.  You could  lose  control  of the  vehicle. 
After  driving  through 
a large  puddle  of water  or 
a  car  wash,  apply  your  brake  pedal  lightly  until 
your  brakes  work  normally. 
Hydroplaning 
Hydroplaning  is  dangerous. So much water can build up 
under your tires that they can actually  ride on the water. 
This  can happen  if the road  is wet  enough and you’re 
going  fast enough. When your vehicle is hydroplaning, 
it  has  little  or  no contact  with the road. 
Hydroplaning doesn’t happen  often. But it can  if your 
tires  do not have much tread  or if the pressure 
in one  or 
more is low. 
It can happen  if a lot of water  is  standing 
on the  road. If  you  can  see  reflections  from trees, 
telephone  poles or  other  vehicles, and  raindrops 
“dimple” the water’s  surface,  there  could  be 
hydroplaning.  Hydroplaning usually happens at higher 
speeds.  There 
just  isn’t 
a hard and fast  rule about hydroplaning.  The 
best advice 
is to  slow down when  it is  raining. 
Driving  Through  Deep  Standing  Water 
I NOTICE: 
If you  drive  too  quickly  through  deep  puddles  or 
standing  water,  water  can  come  in  through  your 
engine’s  air  intake  and  badly  damage  your 
engine.  Never  drive  through  water  that  is  slightly 
lower  than  the  underbody  of 
your vehicle.  If  you 
can’t  avoid  deep  puddles  or  standing  water,  drive 
through  them  very  slowly. 
Some  Other  Rainy  Weather Tips 
Besides slowing down, allow some  extra  following 
distance.  And be especially careful when  you pass 
another  vehicle. Allow yourself more  clear room 
ahead,  and be prepared  to have your view  restricted 
by  road  spray. 
Have good tires with proper tread  depth.  (See 
“Tires”  in 
the Index.) 
4-19 
ProCarManuals.com