clock OPEL FRONTERA 1998 Repair Manual

DIGITAL
CLOCKCIGARETTE
LIGHTER
B-2
BODY-RH
2I-27 0.5
R/W5.0
W
C-16 10A
CLOCK(B)
ROOMC-11 10A
AUDIO(ACC),
MIRRORC-12 20A
CIGAR
5
H-26 BATT(+)
5.0
W
C-15 20A
AUDIO
TEL BATT(+)3.0
B/R
C-2 15A
SEAT
HEATER
5I-27
15
H-48 0.5
O/G
0.5
R/W0.5
O/G
0.3
B1.25
B 1.25
O/B 1.25
O/B
0.3
R/G 0.85
G/R
2.0
B
2.0
B 3.0
L/B
8
H-26
3
I-27 STARTER SW
(ACC) STARTER SW
(IG2)
4I-27 0.85
G/R
ILLUMINATION
CONTROLLER(3)TAIL RELAY
(4)CAR
TELEPHONE
B-18
BODY-LH
4B-582B-58 1.25
R/W1.25
GR
1.25
B
2.0
B
B-26
BODY-CTR
2.0
B
B-2
BODY-RH
2.0
B 3
B-581
B-58 0.5
O/G
1I-21 1I-2016
H-48
1
I-22
2I-20
D08RWA63

D08RW704
STARTER SW
(SW)
3.0
W/G
0.5
W/R
0.5
W/L
1.25
W/L
0.5
L
0.5
L 1.25
W/R
1.25
W/R
0.5
L 0.5
W/R
MODE
SW
(A/T)
ANTI-THEFT
INDICATOR
LIGHT
STARTER
RELAY
ANTI-THEFT & KEYLESS ENTRY CONTROL UNIT0.5
W/R (M/T) C-1 10A
STARTER
RELAYBATT.(+)
5.0
W
0.5
R/WC-16
10A
CLOCK(B)
ROOM
2
15
H-12
H-10
1
M-25
4M-25
6
X-17
22
B-2210B-22 12
H-15
5
X-1716
H-10
4
H-42
A
A
STARTER SW
(ACC)
3.0
L/B
0.5
O/LC-13
10A
ANTI
THEFT
18
B-2220B-225
H-21
DOME
LIGHT
0.5
GR/G
19B-227
H-262
I-8
1
I-820
H-26 BATT.(+)
0.3
LG/B0.3
LG/B1.25
LG/W1.25
LG/W5.0
W
C-18 20A
DOOR LOCK

D08RW703
STARTER SW
(ST)
3.0
W/G
0.5
W/R0.5
W/R
0.5
W/R
0.5
L 0.5
L
STARTER
RELAYANTI-THEFT
INDICATOR
LIGHT
ANTI-THEFT & KEYLESS ENTRY CONTROL UNIT
C-1 10A
STARTER
RELAYBATT.(+)
5.0
W
0.5
R/WC-16
10A
CLOCK(B)
ROOM
1
C-57
12
H-15
10
B-22 22B-22
STARTER SW
(ACC)
3.0
L/B
0.5
O/LC-13
10A
ANTI
THEFT
18
B-2220B-225
H-21
DOME
LIGHT
0.5
GR/G
19B-227
H-262
I-8
1
I-820
H-26 BATT.(+)
0.3
LG/B0.3
LG/B1.25
LG/W1.25
LG/W5.0
W
C-18 20A
DOOR LOCK
2
C-57
4H-422
H-12

D08RW686
5.0
W
5.0
R/WBATT.(+)
C-16 10A
CLOCK(B)
ROOM
1X-8
3X-8
HORN
B-2118
5.0
W
1.25
LG/WBATT.(+) BATT.(+)
C-18 20A
DOOR
LOCK
B-209
3.0
L/B
0.5
O/L STARTER SW
(ACC)
C-13 10A
ANTI-THEFT
DIODEANTI-THEFT
RELAY
5.0
W
2.0
G/O
0.85
G/O0.85
G/O
0.3
B/O
0.3
B/O
0.3
B/O
0.5
O/B0.5
O/B 0.3
O/B0.85
O/B 0.3
B/O0.85
G/Y0.85
G/O0.85
G/O0.85
G/O F-3 15A
HORN
HORN
RELAY
ANTI-THEFT
HORN
B-203B-2119
X-82
H-1516
BATT.(+)
5.0
W
F-7 15A
ANTI-THEFT/
ACC SOCKET
3X-16
TURN
SIGNAL
LIGHT
-LH 0.85
G/B 0.85
P/B
0.5
G/Y
0.5
G/Y1X-16
TURN
SIGNAL
LIGHT
-RH
HORN SW
4B-462
C-19
B-463
C-191
X-165X-164X-162
H-136
B-2114
H-1517
6X-16
ANTI-THEFT & KEYLESS ENTRY CONTROL UNIT

D08RW920
I-8
1
I-82
1H-8 3.0
L/B 5.0
W
0.5
O/L 0.5
R/WC-16
10A
CLOCK(B)
ROOMC-13
10A
ANTI
THEFTF-1 15A
RR COOLER/
ANTI THEFTC-18 20A
DOOR LOCK
MODE
SW
(A/T)ANTI-THEFT
HORN
ANTI-THEFT
INDICATOR
LIGHT
0.5
W/L
1.25
W/L
1.25
B/W
1.25
W/R
0.5
GR/G0.5
O/B
0.5
L 0.5
L/B0.5
L 0.5
L 0.5
W/R
0.5
O/B 0.85
G/O 0.85
G/O1.25
LG/W
1.25
LG/W
0.3
LG/B
0.3
LG/B 5.0
W5.0
W
(M/T)
0.5
W/R0.5
W/R BATT.(+)BATT.(+) BATT.(+) STARTER SW
(ACC)
16
H-1015
H-10
1
M-25
B-2210
A
A
B-2218
H-424
M-25
4
B-2220B-228B-2219B-2222
H-153
H-413
H-261
H-159
C-191
3.0
W/G
C-110A
STARTER
RELAY STARTER SW
(ST)
C-19
2
H-2612
H-425
H-21 DOME
LIGHT
5
ANTI-THEFT & KEYLESS ENTRY CONTROL UNITSTARTER
RELAY
5X-17
X-176

D08RW709
STARTER SW
(ST)
3.0
W/G
0.5
W/R0.5
W/R
0.5
L 0.5
L
STARTER
RELAYANTI-THEFT
INDICATOR
LIGHT
ANTI-THEFT & KEYLESS ENTRY CONTROL UNIT
C-1 10A
STARTER
RELAYBATT.(+)
5.0
W
0.5
R/WC-16
10A
CLOCK(B)
ROOM
1
C-57
12
H-15
10
B-22 22B-22
STARTER SW
(ACC)
3.0
L/B
0.5
O/LC-13
10A
ANTI
THEFT
18
B-2220B-225
H-21
DOME
LIGHT
0.5
GR/G
19B-221
H-262
I-8
1
I-812
H-26 BATT.(+)
0.3
LG/B0.3
LG/B1.25
LG/W1.25
LG/W5.0
W
C-18 20A
DOOR LOCK
2
C-57
6H-12

8E–14METER AND GAUGE
Removal
1. Disconnect the battery ground cable.
2. Remove the front console assembly(1).
Refer to the Instrument Panel Assembly in Body
Structure section.
3. Remove the lower cluster assembly(2).
Refer to the Instrument Panel Assembly in Body
Structure section.
4. Remove the instrument panel driver lower cover(3).
Refer to the Instrument Panel Assembly in Body
Structure section.
740RS004
5. Remove four fixing screws and disconnect the meter
connectors to remove the meter assembly(5).
825RW031
CAUTION: The removed meter assembly should be
placed upright or with its face side up.
Installation
To install, follow the removal steps in the reverse order.
Warning Light Bulb, Indicator Light Bulb, Illumination Light Bulb,
A/T Indicator Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the meter assembly(1).
Refer to the Meter Assembly removal steps in this
section.
3. Hold the bulb socket by hand and rotate it
counterclockwise to remove the socket & bulb(2)
from the meter body.
825RW032
Installation
To install, follow the removal steps in the reverse order.

SEATS8G–17
Disassembly (Split Type)
1. Remove the back board.
Remove the clips and the back board.
2. Remove the device cover.
3. Remove the release knob.
Turn the knob counterclockwise to remove it.
4. Remove the release rod.
Disconnect the rod from the linkage bush.
5. Remove the reclining device.
755RS004
6. Remove the connecting shaft.
7. Remove the seat back assembly.
8. Remove the pillow assembly.
Turn up the seat back trim cover and slit the pad
from the back around to the place where the lock
spring(2) of the guide bush(1) is.
Then insert a finger through the slit and pull out the
pillow while you are pressing down on the lock spring.
755RS017
9. Remove the band hook cover.
10. Remove the armrest assembly.
Turn up the seat back trim cover and remove the
fixing nuts.
11. Remove the armrest set bracket.
12. Remove the armrest board.
13. Remove the trim cover.
Remove the trim cover fixing hog rings from the
backside of the seat back.
With close attention paid to the hog rings and the
wire which connect the trim cover and the pad and
frame assembly, remove the trim cover while
turning it up.
14. Remove the pad & frame assembly.
15. Remove the seat cushion assembly.
16. Remove the seat lock cover.
17. Remove the rear seat belt buckle and lock assembly.
18. Remove the mounting bracket.
19. Remove the return spring.
20. Remove the spring collar.
21. Remove the trim cover.
Remove the hog rings and pull the trim cover out
from the frame assembly groove.
With close attention paid to the hog rings and the
wire which connect the trim cover and the pad &
frame assembly, remove the trim cover while
turning it up.
22. Remove the frame assembly.
23. Remove the pad assembly.
24. Remove the stopper rubber.

SEATS8G–19
Disassembled View (Short Wheel Base)
755RW036
Legend
(1) Back Board
(2) Release Knob
(3) Release Rod
(4) Device Cover
(5) Reclining Device
(6) Linkage Bush
(7) Pillow Assembly
(8) Pad & Frame Assembly
(9) Armrest Board
(10) Clip
(11) Band Hook Cover
(12) Trim Cover(13) Armrest Set Bracket
(14) Bush
(15) Armrest Assembly
(16) Trim Cover
(17) Mounting Bracket
(18) Frame Assembly
(19) Stopper Rubber
(20) Pad Assembly
(21) Seat Lock Cover
(22) Rear seat Belt Bukle and Lock Assembly
(23) Seat Cushion Assembly
(24) Free Hinge Cover
(25) Seat Back Assembly
Disassembly
1. Remove the back board.
Remove the clips and the back board.2. Remove the device cover.
3. Remove the release knob.Turn the knob counterclockwise to remove it.

8G–22SEATS
Disassembly (Bench Type)
1. Remove the device cover.
2. Remove the release knob.
Turn the knob to the counterclockwise to remove it.
3. Remove the release rod.
Disconnect the rod from the linkage bush.
4. Remove the reclining device.
755RS004
5. Remove the connecting shaft.
6. Remove the seat back assembly.
7. Remove the band hook cover.
8. Remove the pillow assembly.
Refer to the Disassembly (Split Type) in this
section.
755RS017
9. Remove the trim cover.
Open the fastener(3), and with close attention paid
to the hog rings and wire which connect the trim
cover and the pad and frame assembly, remove the
trim cover as you turn it up.
750RW011
10. Remove the pad & frame assembly.
11. Remove the seat cushion assembly.
12. Remove the seat lock cover.
13. Remove the rear seat belt buckle and lock assembly.
14. Remove the mounting bracket.
15. Remove the trim cover.
Remove the hog rings and pull the trim cover out
from the frame assembly groove.
With close attention paid to the hog rings and the
wire which connect the trim cover and the pad and
frame assembly, remove the trim cover while
turning it up.
16. Remove the frame assembly.
17. Remove the pad assembly.
18. Remove the stopper rubber.