length OPEL GT-R 1973 Owner's Manual

8A-61973 OPEL SERVICE MANUAL
9. On installation make sure that the gaps between
headlamp housing in closed position and headlamp
opening is equal all round and housing is flush in its
height with the body.
REMOVAL AND INSTALLATION OF HEADLAMP
CABLE ASSEMBLY
Removal1. Remove cotter pin. See Figure
EA-13 “CL”2. Remove trunion block and nut. See Figure SA-13
“D.”
3. Remove outer adjusting nut and pull cable
through bearing. See Figure 8A-13 “B.”
4. Pull cable through front chassis support.
5. Hoist car.
6. Remove wire clip and unsnap ball seat at control
lever. See Figure 8A-14 “A.”
7. Remove ball-socket and lock nut. See Figure SA-
14
“B.”8. Remove rear adjusting nut. See Figure 8A-14
“CL”9. Remove cable from retainers.
Figure SA-13 Removing Headlamp Trunion Block
Installation10. Thread cable through bearing and clip retainers.Figure 8A-14 Removing Ball Seat at Control Lever
11. Install adjusting lock nut approximately
l/2” on
thread. See Figure 8A-13 “B.’
12. Install lock nut and ball stud on end of cable. See
Figure 8A-14 “B.”
13. Connect ball stud to control lever with clip. See
Figure 8A-14 “A.”
14. Adjust lock nut under vehicle for maximum cable
length. See Figure 8A-14
“CL”15. Thread cable through proper openings in body
and install adjusting lock nut, trunion lock nut, trun-
ion, and lock clip.
16. Adjust cable length for proper headlight operat-
ion.
REMOVAL AND INSTALLATION OF RADIATOR
GRILLE
(GT)
RemovalRemove screws securing grille screen to opening.
InstallationInstall grille screen to opening and secure with
screws.
REMOVAL AND INSTALLATION OF
RADIATOR GRILLE EXTENSIONS
(GTI
Removal
1. Remove hex head screw and washer holding grille
extension to baffle plate.

98-34 1973 OPEL 3ERVlCE MANUAL
9B-23Figure
98.26 Compressor Front and Rear Heads
and circulated through the system via a 3/16 inch
diameter oil passage through the shaft center and
also four 5/64 inch diameter holes drilled perpen-
dicular to the shaft. The inner rotor is driven by the
shaft.TUBE
Figure
98-27 Compressor Oil Flow
4. Shaft and
Gash Plate Assembly - The shaft andwash plate assembly (see Figure 9B-162) consists of
an elliptical plate positioned obliquely to the shaft.
As the plate and shaft rotate, the surface of the plate
moves to and fro lengthwise relative to the centerline
of the shaft. This reciprocating motion is transmitted
to the pistons which contact the surface of the wash
plate. A woodruff key locks the wash plate onto theshaft. The wash plate and shaft are serviced as an
assembly. The shaft is driven by a pulley when the
magnetic clutch is energized. A needle thrust bearing
and
L mainshaft bearing support the shaft horizon-
tally and vertically.
5. Needle Thrust Bearing and Races
- Two needle
thrust bearings, each“sandwiched” between two
races are located on either side of the wash plate
hub. The front needle thrust bearing and races pro-
vide 0.010” to 0.015” clearance between the top of
the pistons and the rear side of the front suction valve
reed disc (see Figure
9B-28). The rear needle thrust
bearings and races provide 0.0005” to 0.0015” clear-
ance between the hub of the wash plate and the rear
hub of the rear cylinder. Races of various thicknesses
are provided for service replacement to achieve re-
quired clearances when rebuilding units.
6. Cylinder Assembly and service Pistons (Factory
installed pistons are ringless) -The cylinder assembly
(front cylinder and rear cylinder) is serviced only as
a matched set. Alignment of the two halves is main-
tained by two dowel (locater) pins.
The double ended pistons are made of cast alumi-
num. There are two grooves on each end of the ser-
vice piston. The outer grooves will receive a piston
ring. The inner grooves act as oil scraper grooves to
collect any excess oil. Two oil return holes are drilled