PEUGEOT 1007 2008 Owner's Manual

1
24
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer’s servicing schedule.
The point at which the next service
is due is calculated from the last
indicator zero reset. It is determined
by two parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Operation
When the ignition is switched on, the
spanner symbolising the servicing
operations comes on; the distance
recorder display indicates the number
of miles [kilometres] (rounded off)
remaining until the next service.

Example: 4,800 miles/km remain be-
fore the next service. For fi ve seconds
after the ignition is switched on, the
display indicates: 10 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total or trip
distance.
10 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit.
It indicates that a service must be
carried out soon. The display indi-
cates the total or trip distance. The service is overdue.
The spanner fl ashes for 5 seconds
each time the ignition is switched on.
10 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit.
The display indicates the total or trip
distance.
The distance remaining before the
next service may be weighted by the
time factor, depending on the user’s
driving habits.
The spanner may also come on if
more than two years have elapsed
since the last service.
The distance remaining to
the next service is less than
500 miles/1,000 km.

Example: 400 miles/900 km remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:

1
25
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder
re-set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears. Total/trip distance recorder
Briefl y pressing the button alternates
between the total and trip distance
displays.
To reset the trip distance recorder to
zero, when it is displayed press the
button until zeros appear.
Lighting rheostat
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the required bright-
ness, release the button.
After this operation, if you
wish to disconnect the bat-
tery, lock the vehicle and
wait for at least fi ve minutes,
otherwise the zero re-set will not be
registered.

1
26
"2 Tronic" gearbox indicator This comes on when
the "AUTO" automated
operation mode is se-
lected.
It is switched off on switching to the
sequential operation mode.
It fl ashes if a malfunction occurs. Gear lever positions:

"Neutral"

"Reverse"
Sequential operating mode
1st gear

2nd gear

3rd gear

4th gear

5th gear
"AUTO" indicator light

1
27
TRIP COMPUTER

 Press the button, located at the
end of the wipers stalk , to dis-
play the various items of trip
computer data in succession. The trip computer data is the following:
System which provides current infor-
mation concerning the route travelled
(range, consumption, ...).

 Press the control for more than
two seconds to reset the dis-
tance travelled, the average con-
sumption and the average speed
to zero.
Monochrome display A
Zero reset
Data displays - the range,
- the current consumption,
- the distance travelled,
- the average consumption,
- the average speed.

 The next press then returns you
to the normal display.

1
28
- the current information tab with:

1
29
Distance remaining to be
travelled
(km or miles)
This is the distance remaining to be
travelled to the fi nal destination. It
is either calculated instantly by the
navigation system if guidance is acti-
vated, or entered by the user.
If the distance is not entered, dashes
are displayed in place of the digits.
Average speed
(km/h or mph)
This is the average speed
calculated since the last
trip computer zero reset
(ignition on).
Range
(km or miles)
This indicates the number of miles
(or kilometres) which can still be
travelled with the fuel remaining in
the tank in relation to the average
consumption over the last few miles
(kilometres) travelled. Current consumption
(l/100 km or km/l or mpg)
This is the average quantity of fuel
consumed over the last few sec-
onds.
Average consumption
(l/100 km or km/l or mpg)
This is the average quantity of fuel
consumed since the last trip computer
zero reset.
Distance travelled
(km or miles)
This indicates the distance travelled
since the last trip computer zero reset.
A few definitions…
When the range falls below 20 miles
(30 km), dashes are displayed. After
fi lling with at least 5 litres of fuel, the
range is recalculated and is displayed
when it exceeds 60 miles (100 km).
If dashes are displayed con-
tinuously while driving in
place of the digits, contact a
PEUGEOT dealer. This function is only displayed
from 20 mph (30 km/h).
This fi gure may increase fol-
lowing a change of driving
style or relief, resulting in a
signifi cant change in the cur-
rent consumption.

1
30
Display C

 Press the "MENU" button to gain
access to the general menu.


Press the arrows, then the "OK"
button to select the "Trip computer"
menu.

 On the "Trip computer" menu,
select one of the following appli-
cations:
Warnings log
This summarises the active warning
messages, displaying them in suc-
cession on the multifunction display.
Status of the functions
This summarises the active or inac-
tive status of the functions present on
the vehicle.
Enter the distance to the
destination
This enables you to enter an approxi-
mate value for the distance to the fi nal
destination.
"TRIP COMPUTER" MENU
System which provides general infor-
mation concerning the status of certain
equipment with which your vehicle is
equipped, such as the warnings log,
the status of the functions...
"DIAGNOSTICS" MENU

 On the "Diagnostics" menu,
select one of the following appli-
cations:
Colour display

 Press the "MENU" button to gain
access to the general menu.

 Turn the dial and press it to
select the "Diagnostics" menu.

2
31
MONOCHROME DISPLAY A (without RD4 audio equipment)
Presentation
This displays the following information:
- the time,
- the date,
- the outside temperature (this fl ashes if there is a risk of ice),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "Anti- pollution system faulty") or infor-
mation messages (e.g.: "Auto
lights on"), displayed temporarily,
can be cleared by pressing the

"ESC" button,
- the trip computer (see corre- sponding section). Parameter configuration
There are three display control buttons:
-
"ESC" to abandon the operation
in progress,
- "MENU" to scroll through the
menus or sub-menus,
- "OK" to select the menu or sub-
menu required. General menu
Press the
"MENU" button to scroll
through the various menus of the
general menu:
- vehicle confi guration,
- options,
- display settings,
- languages,
- units.
Press the "OK" button to select the
menu required.

2
32
Vehicle confi guration
Once the "Vehicle confi guration"
menu has been selected, you can
activate or deactivate the following
equipment:
- wiper linked with reverse gear,
- "follow-me-home" lighting. Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu has
been selected, you can gain access
to the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty). Once you have selected a setting,
press the
"OK" button to change its
value.
Wait for approximately ten sec-
onds without any action to allow the
changed data to be recorded or press
the "ESC" button to cancel.
The display then returns to the nor-
mal display. Units
Once the "Units" menu has been
selected, you can change the units
of the following parameters:
- temperature (°C or °F),
- fuel consumption (l/100, mpg or
km/l).
For safety reasons, it is im-
perative that confi guration of
the multifunction displays by
the driver takes place when
stationary.

2
33
General menu
Press the "MENU" button to gain
access to the general menu, then
press the "  " or "  " buttons to scroll
through the following items:
- radio-CD,
- vehicle confi guration,
- options,
- display settings,
- languages,
- units.
Press the "OK" button to select the
menu required. Vehicle confi guration
Once the "Vehicle confi guration"
menu has been selected, you can
activate or deactivate the following
equipment:
- rear wiper linked with reverse
gear,
- "follow-me-home" lighting.
Presentation
This displays the following informa-
tion, via the RD4 audio equipment
control keypad:
- the time,
- the date,
- the outside temperature (this fl ashes if there is a risk of ice),
- the audio source displays (radio, CD, ...),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "Anti- pollution system faulty") or infor-
mation messages (e.g.: "Auto
lights on"), displayed temporarily,
can be cleared by pressing the

"ESC" button,
- the trip computer (see corre- sponding section).
MONOCHROME DISPLAY A
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty).
Radio-CD
With the RD4 audio equipment
switched on, once the "Radio-CD"
menu has been selected, you can
activate or deactivate the functions
linked with the use of the radio (RDS
following, REG mode), the CD or the
CD changer (introscan, random play,
CD repeat).