display PEUGEOT 1007 2008 Owner's Manual

Page 36 of 189

2
39
COLOUR SCREEN
Displays on the screen
When the ignition is switched on, this
displays the following information
automatically and directly:
- the time,
- the date,
- the outside temperature (if there is a risk of ice, you are warned
by a message).
Warning messages (e.g.: "Fuel level
low") and vehicle function status
messages (e.g.: "Automatic switching
on of the headlamps activated")
may appear temporarily. These can
be cleared by pressing the "ESC"
button. General menu
When the RT4 GPS audio/telephone
is switched on, select the menu
which corresponds to the following
applications:
- the satellite navigation system,
- the guidance on the map,
- the traffi c information,
- the audio sources (radio, CD,
Jukebox, ...),
- the telephone directories and functions,
- the confi guration of the screen and the setting of the parameters
of the vehicle’s equipment,
- the displaying of a video.
- the vehicle diagnostics (warnings log and status of the functions). Controls
From the RT4 GPS audio/telephone
control panel, to select one of the
applications:

 press the "MENU" button to gain
access to the general menu ,

 turn the dial to move the selection,

 press the dial to confi rm the
selection,
or

 press the "ESC" button to aban-
don the operation in progress and
return to the previous display.
For further details concerning these
applications, refer to the RT4 part of
the "Audio and Telematics" section.

Page 37 of 189


2
40
Selection of the language
Once the "Selection of the language"
menu has been selected, you gain
access to the following parameters:
- selection of the display, infor-mation and voice commands
language (Français, English,
Italiano, Portugues, Espanol,
Deutsch, Nederlands).
Display confi guration
Once the "Display confi guration"
menu has been selected, you gain
access to the following parameters:
- selection of the palette of colours available for the display,
- setting of the brightness and bril- liance of the display,
- setting of the date and time (12 or 24 hour mode, adjustment
of the minutes on GPS),
- selection of the units (tempera- ture in °Celsius or °Fahrenheit;
consumption in l/100 km or mpg
or km/l).
Sounds
Once the "Sounds" menu has been
selected, you gain access to the
following parameters:
- setting of the voice commands,
- setting of the voice synthesiser (volume of the instructions
and other messages, male or
female),
- activation of the auxiliary input AUX. Defi ne the vehicle parameters
Once the "Defi ne the vehicle param-
eters" menu has been selected, you
can activate or deactivate certain
driving and comfort equipment:
- wiper linked with reverse gear
(refer to the "Visibility" section),
- "follow-me-home" lighting and duration (refer to the "Visibility"
section).
"Configuration" menu

 Press the "MENU" button on
the RT4 GPS audio/telephone
to gain access to the general
menu .

 Turn the dial to select the

"Confi guration" menu, then
press it to confi rm.
Once this menu has been selected,
you can gain access to the following
functions:

Page 45 of 189

3
48
AUTOMATIC AIR CONDITIONING
The air conditioning can only operate when the engine is running.
1. Automatic "comfort" programme
We recommend that you use this
mode, it provides optimised auto-
matic control of all of the following
functions: passenger compartment
temperature, air fl ow, air distribution
and air intake, in accordance with the
comfort value that you have chosen.
This system is designed to operate
effectively in all seasons, with the
windows closed. Press the
"AUTO" button.
The "AUTO" symbol is
displayed. The automatic comfort
programme may not be
suffi cient for rapid de-icing or
demisting of the windscreen
and side windows (humidity,
several passengers, ice, etc.).
In this case, select the automatic
visibility programme. The button 3
indicator light comes on.
The system automatically controls
the air conditioning and the fl ow of air
and provides optimum distribution of
the ventilation to the windscreen and
side windows. It deactivates the air
recirculation.
To exit this programme, press
button 3 again or press the "AUTO"
button, the indicator light on the
button is switched off and "AUTO" is
displayed.

Note: for your comfort, when the
engine is switched off, the settings are
retained until the engine is switched
on again, if the temperature in the
passenger compartment has not
altered signifi cantly; otherwise, opera-
tion resumes in automatic mode.
When the engine is cold, to prevent
too great a distribution of cold air, the
air fl ow will only reach its optimum
level gradually. 3. Automatic "visibility" programme
Automatic operation
The value indicated on
the display corresponds
to a level of comfort and
not to a temperature
in degrees Celsius or
Fahrenheit.
2. Temperature adjustment On entering the vehicle, if
the interior temperature is
much colder or warmer than
is comfortable, there is no
need to change the value displayed
in order to reach the required level of
comfort. The system eliminates the
temperature difference automatically
and as quickly as possible.
Press the
"+" and "-" buttons to
change this value. A setting around
the value 22 enables optimum
comfort to be obtained. However,
depending on your requirements, a
setting between 18 and 24 is usual.

Page 46 of 189

3
49
Press this button to switch
off the air conditioning.
Automatic operation of the
air conditioning is resumed
when the button is pressed
again. The symbol "A/C" is displayed.
4. Air conditioning on/off
Pressing this button several
times in succession enables
the air fl ow to be directed in
turn towards:
- the windscreen and the side windows (de-icing or demisting),
- the windscreen, the side windows, the vents and the footwells,
- the windscreen, the side windows and the footwells,
5. Air distribution adjustment Press buttons
"+" or "-"
respectively to increase
or reduce the air fl ow.
The air fl ow symbol, the fan, fi lls
progressively in relation to the value
requested.
6. Air fl ow adjustment
Press the air fl ow
"-" button 6 until
the fan symbol is empty.
This action switches off all of the
functions of the air conditioning
system, with the exception of the rear
screen demisting 9 .
Avoid driving with the air conditioning
switched off for long periods.
Pressing the air fl ow "+" button 6 again
or the "AUTO" button reactivates the
system with the values set before it
was switched off.
7. Switching the system off
Control using the manual
buttons
It is possible to adjust one or more
functions manually while leaving the
other functions in automatic mode.
The
"AUTO" button indicator light
switches off.
Switching to manual mode may result
in discomfort (temperature, humidity,
odour, condensation) and does not
provide optimum comfort.
To return to automatic mode, press
the "AUTO" button. Press this button for
recirculation of the interior
air. The air recirculation
symbol
8 is displayed.
Air recirculation enables the passenger
compartment to be isolated from
exterior odours and smoke.
Avoid prolonged recirculation of
interior air (risk of condensation or
deterioration of the air quality).
Press this button again or press the

"AUTO" button to resume automatic
management of the intake of air.
8. Air intake/Air recirculation
With the engine running,
press this button to demist
the rear screen and the
exterior mirrors. The
indicator light on button 9
comes on.
Demisting switches off automatically
in relation to the exterior temperature
and to prevent an excessive
consumption of current.
It is possible to stop operation of the
demisting before it is switched off
automatically by pressing the button
again.
If the engine is switched off before the
demisting is switched off automatically,
the demisting will resume the next
time the engine is switched on.
9. Demisting the rear screen and
the mirrors
- the footwells,
- the centre vents, the side vents
and the footwells,
- the centre and side vents.

Page 71 of 189

4
74
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by any-
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code is
recognised and starting is possible.

If the system does not function
correctly, the service warning light
comes on, accompanied by an
audible signal and a message on the
multifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.

Lost keys
Visit a PEUGEOT dealer with the
vehicle’s V5 registration certifi cate
and your personal identifi cation docu-
ments.
A PEUGEOT dealer will be able to
retrieve the key code and the trans-
ponder code required to order a
replacement key.
Programming the remote
control
Following changing of the remote
control battery or disconnection of
the vehicle battery, the remote control
must be reprogrammed.

 Wait at least one minute before
using the remote control.

 Switch on the ignition.

 Press button B or C for at least
fi ve seconds within the next ten
seconds.

 Switch off the ignition.

 Wait at least one minute before
using the remote control.
The remote control is now working
again.
Changing the remote control
battery
Battery ref.: CR1620/3 volts.
The information "battery fl at" is given
by displaying of the service warning
light, accompanied by an audible
signal and a message on the multi-
function display.
To replace the battery, unclip the
casing using a coin at the notch.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.

Page 73 of 189

4
74
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by any-
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code is
recognised and starting is possible.

If the system does not function
correctly, the service warning light
comes on, accompanied by an
audible signal and a message on the
multifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.

Lost keys
Visit a PEUGEOT dealer with the
vehicle’s V5 registration certifi cate
and your personal identifi cation docu-
ments.
A PEUGEOT dealer will be able to
retrieve the key code and the trans-
ponder code required to order a
replacement key.
Programming the remote
control
Following changing of the remote
control battery or disconnection of
the vehicle battery, the remote control
must be reprogrammed.

 Wait at least one minute before
using the remote control.

 Switch on the ignition.

 Press button B or C for at least
fi ve seconds within the next ten
seconds.

 Switch off the ignition.

 Wait at least one minute before
using the remote control.
The remote control is now working
again.
Changing the remote control
battery
Battery ref.: CR1620/3 volts.
The information "battery fl at" is given
by displaying of the service warning
light, accompanied by an audible
signal and a message on the multi-
function display.
To replace the battery, unclip the
casing using a coin at the notch.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.

Page 79 of 189

4
80
Automatic central locking
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h).
You can activate or deactivate this
function. Driving with the doors locked
may make access to the
passenger compartment by
the emergency services more
diffi cult in an emergency.
Activation
With the ignition on, press and hold
button A .
Activation of the function is accom-
panied by an audible signal and a
message on the multifunction display.
Deactivation
With the ignition on, press and hold
button A .
Deactivation of the function is
accompanied by an audible signal
and a message on the multifunction
display.
"Door open" alert -
when the vehicle is moving,
by lighting of the "door open"
warning light, accompanied by
an audible signal and a message
on the multifunction display for a
few seconds.
Opening/Closing using the
remote control
Press button C or D to open or close
the left or right door.
The opening and closing of the
door is accompanied by an audible
signal.
2nd press on button C or D during
opening/closing  interruption of the
movement.
3rd press on button C or D  move-
ment of the door in the opposite
direction.
You are advised to use the
remote control or the con-
trols as much as possible.
Opening/Closing from the front
Press switch
B to open or close the
corresponding door.
Choosing the movement of the door
using the controls:
- pull  opens the door,
- push  closes,
- second press  stops the
movement,
- the controls do not function above 3 mph (5 km/h).
If a door or the boot is not
closed properly, you are
warned:
- when the engine is running,
by lighting of the "door open"
warning light, accompanied by
a message on the multifunction
display for a few seconds.

Page 80 of 189

4
81
General
recommendations
Always check that it is safe to operate
the door and be sure, in particular, not
to leave children or animals near the
door controls without supervision.
When opening the door, with the win-
dow open, ensure that no person,
animal or object is hanging through
the window.
Before any opening or closing and
during any movement of the doors,
ensure that no person, animal or
object is preventing the required
manoeuvre, either inside or outside
the vehicle.
It is imperative that the doors are
ope-rated only when the vehicle is
stationary.
For your safety and for that of your
passengers, as well as for correct ope-
ration of the doors, you are strongly
advised not to drive with a door open.
The audible warning, the lighting of
the "door open" warning light and the
message on the multifunction display
are there to remind you.
Lock your vehicle when using an
automatic carwash. The doors and the overall
dimensions of the vehicle
Safety/Obstacle detection
The obstacle detection system is
triggered when an obstacle of a
certain physical resistance hinders
the movement of the door.


Page 82 of 189

4
83
TAILGATE
Tailgate release
This enables the tailgate to be
unlocked in the event of a central
locking fault.
- Fold back the rear seats to gain access to the lock from inside
the boot,
- Insert a small screwdriver into hole A of the lock to unlock the
tailgate.
"Tailgate open" warning
In this case, or following reconnection
of the battery, with the doors open, it
may be necessary to close the doors
manually, in order to reinitialise them,
and start the engine. If the tailgate is not closed
properly, you are warned:
- with the engine running , by
lighting of the "door open" war-
ning light, accompanied by a
message displayed briefl y on the
multifunction display.
- when the vehicle is moving , by
lighting of the "door open" war-
ning light, accompanied by an
audible signal and a message
displayed briefl y on the multi-
function display.
The tailgate locks automati-
cally when the vehicle speed
reaches 6 mph (10 km/h).
It unlocks when one of the
doors is opened if the speed is below
3 mph (5 km/h) or when the central
locking button on the centre console
is pressed.

When the door has stopped in an
intermediate position (neither fully
open nor fully closed), only the
remote control or the controls per-
mit electric operation of the door.
When closing requests are made
when the door is in a partially open
position, the door may open slightly
before closing.
When closing a door electrically when
the battery is low, you are advised to
guide the door manually. Recharge
the battery as soon as possible.
If the electric controls (remote control
or controls) no longer operate, reini-
tialise the door(s) as follows:

1. Start the engine.

2. Manually open the door(s) fully.

3. Close the door(s) fully.
On completion of this procedure,
electric operation of the doors is
restored.
However, if a problem persists
following this procedure, contact a
PEUGEOT dealer. Simultaneous locking or
unlocking of the tailgate and the
doors
The tailgate is locked or unlocked by
the remote control or from the driver’s
door lock.
To open, press the control
1 and lift
the tailgate.

Page 83 of 189

4
83
TAILGATE
Tailgate release
This enables the tailgate to be
unlocked in the event of a central
locking fault.
- Fold back the rear seats to gain access to the lock from inside
the boot,
- Insert a small screwdriver into hole A of the lock to unlock the
tailgate.
"Tailgate open" warning
In this case, or following reconnection
of the battery, with the doors open, it
may be necessary to close the doors
manually, in order to reinitialise them,
and start the engine. If the tailgate is not closed
properly, you are warned:
- with the engine running , by
lighting of the "door open" war-
ning light, accompanied by a
message displayed briefl y on the
multifunction display.
- when the vehicle is moving , by
lighting of the "door open" war-
ning light, accompanied by an
audible signal and a message
displayed briefl y on the multi-
function display.
The tailgate locks automati-
cally when the vehicle speed
reaches 6 mph (10 km/h).
It unlocks when one of the
doors is opened if the speed is below
3 mph (5 km/h) or when the central
locking button on the centre console
is pressed.

When the door has stopped in an
intermediate position (neither fully
open nor fully closed), only the
remote control or the controls per-
mit electric operation of the door.
When closing requests are made
when the door is in a partially open
position, the door may open slightly
before closing.
When closing a door electrically when
the battery is low, you are advised to
guide the door manually. Recharge
the battery as soon as possible.
If the electric controls (remote control
or controls) no longer operate, reini-
tialise the door(s) as follows:

1. Start the engine.

2. Manually open the door(s) fully.

3. Close the door(s) fully.
On completion of this procedure,
electric operation of the doors is
restored.
However, if a problem persists
following this procedure, contact a
PEUGEOT dealer. Simultaneous locking or
unlocking of the tailgate and the
doors
The tailgate is locked or unlocked by
the remote control or from the driver’s
door lock.
To open, press the control
1 and lift
the tailgate.

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 61-70 ... 90 next >