Peugeot 307 2007.5 Owner's Manual

10PRACTICAL INFORMATION
118
Removing the wheel

 If necessary, place a chock under
the wheel diagonally opposite to
the one to be changed.

 Remove the trim, using the
wheelbrace 1 , pulling at the valve
passage hole.

 Loosen the wheel bolts (for
vehicles i tted with alloy wheels,
remove the chrome trim i rst. See
paragraph on ‘Special features of
alloy wheels’).

 Place the jack 2 in contact with
one of the four locating points A
on the sub-frame (the one which
is closest to the wheel to be
changed).

 Extend the jack 2 until its base
is in contact with the ground.
Ensure that the centre line of the
base of the jack is straight above
the locating point A used.
 Raise the vehicle.

 Unscrew the bolts and remove
the wheel.
Fitting a wheel

 Position the wheel using the
centralising tool 3 to assist you.

 Tighten the bolts by hand and
remove the centralising tool.

 Partly tighten the bolts using the
wheelbrace 1 .

 Fold the jack 2 and remove it.

 Fully tighten the bolts using the
wheelbrace 1 .

 Replace the wheel trim, starting
by placing the wheel trim notch
opposite the valve, and press it
on using the palm of the hand.
Extracting the wheel

 Unscrew the yellow central bolt a
quarter turn.

 Raise the spare wheel towards
you from the rear.

 Remove the wheel from the
boot.

10PRACTICAL INFORMATION
119
Putting the wheel back in place

 Put the wheel back in place.

 Unscrew the yellow central bolt a
few turns, then put it in place in
the centre of the wheel.

 Tighten the central bolt fully until it
clicks to secure the wheel i rmly.
 Put the tool holder back in the
centre of the wheel and clip it.

 Put the boot l oor back in place.
Wheels i tted with the Tyre Under-
Inl ation Detection system
For further information refer to "Tyre
under-inl ation detection" in the
safety section.
The wheel must be positioned
l at, in the centre of its
housing.
For your safety, always
change the wheel:
- on level, stable, non-slippery ground,
- with the handbrake on and the ignition switched off,
- with i rst or reverse gear engaged (position P for the automatic
gearbox),
- with the vehicle chocked.

Never go underneath a vehicle that is
supported only by a jack (use a ramp).
* According to model and country. After changing the wheel:
- have the tightening of the bolts
and the tyre pressure checked by
a PEUGEOT dealer as soon as
possible,
- have the punctured tyre repaired and rei t it to the vehicle as soon
as possible.
Recommendations when using
the temporary spare wheel *
Your vehicle may be equipped with a
spare wheel which has a different rim
to the standard wheel.
After use, it must be replaced as
quickly as possible.
Observe the following instructions to
avoid altering the behaviour of the
vehicle:
-
do not exceed 50 mph (80 km/h) ,
- do not i t a wheel trim,
- drive with care,
- check the tyre pressure indicated
on the label.

10PRACTICAL INFORMATION
123
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool 6 to remove the
trims before slackening the bolts. Wheel with centre trim
Fitting snow tyres
If you i t snow tyres mounted on
steel wheels onto your vehicle, it
is essential to use special bolts
available from your PEUGEOT
dealer.
 slide the trim remover 7 into the
notch of the centre trim,

 use the trim remover as a lever
pressing on the trim to unclip it,

 unscrew the bolt using the anti-
theft socket and the wheelbrace.
If your vehicle is i tted with a steel
spare wheel, when i tting it, it is

normal when tightening the bolts to
notice that the washers do not come
into contact with the rim. The spare
wheel is secured by the cone shape
of each bolt.
This anti-theft socket was
given to you on delivery
of your vehicle along with
the duplicate keys and the
coni dential card.
Make a careful note of the code
number engraved on the head of the
anti-theft socket. This will enable you
to obtain a duplicate socket from a
PEUGEOT dealer.
Special features of alloy wheels
Fitting the spare wheel
Anti-theft bolts
Your wheels are i tted with an anti-
theft bolt, one per wheel.
Bolt covers
Wheel with chrome trim

 remove the chrome trim,

 unscrew the bolt using the anti-
theft socket and the wheelbrace.

10PRACTICAL INFORMATION
120
Parking the vehicle

 As far as possible, park the
vehicle on level, stable and non-
slippery ground.

 Apply the handbrake, switch off
the ignition and engage i rst or
reverse gear (position P for the
automatic gearbox). Access to the spare wheel

 Open the boot.

 Open the l ap using the lug
to release the winch and gain
access to its control nut.

 Unscrew the nut fully, using the
wheelbrace 1 , to unroll the winch
cable.
Tools
The following tools are located:
- in the right-hand trim of the boot,

1. Wheelbrace.
2. Removable towing eye.
3. Socket for anti-theft bolts.
- in the holder in the centre of the spare wheel,
4. Jack with handle.
5. Centralising tool.
6. Bolt cover tool.
CHANGING A WHEEL (ESTATE)

10PRACTICAL INFORMATION
121

 Detach the wheel/holder assembly
from the rear of the vehicle.

 Take out the notched hook to
release the wheel, as shown in
the illustration. Removing the wheel

 Slide the holder cover to gain
access to the tools.

 If necessary, place a chock under
the wheel diagonally opposite to
the one to be changed.

 Remove the trim, using the
wheelbrace 1 , pulling at the valve
passage hole (for vehicles i tted
with steel wheels).

 Loosen the wheel bolts (see
§ "Special features of alloy
wheels" for vehicles i tted with
alloy wheels).
Note
: you can use the other end
of the tool 6 to unscrew the wheel
bolts.
 Place the jack 4 in contact with
one of the four locating points

A on the sub-frame; the closest
possible to the wheel to be
changed.

 Extend the jack 4 until its base
is in contact with the ground.
Ensure that the centre line of the
base of the jack is straight above
the locating point A used.

 Raise the vehicle.

 Remove one bolt and position the
centralising tool 5 in its place.

 Unscrew the other bolts and
remove the wheel.

10PRACTICAL INFORMATION
122
Fitting a wheel

 Position the wheel using the
centralising tool 5 to assist you.

 Tighten the bolts by hand and
remove the centralising tool 5 .

 Partly tighten the bolts using the
wheelbrace 1 .

 Fold the jack 4 and remove it.

 Fully tighten the bolts using the
wheelbrace 1 .

 Replace the wheel trim, starting
by placing the wheel trim notch
opposite the valve, and press it
on using the palm of the hand.

 Put the corresponding tools in the
holder and secure its cover.

 Place the holder on the ground
and align the spare wheel on it.

 Pass the notched hook into the
holder cover.

 Rei t the wheel under the vehicle
tightening the winch control nut
using the wheelbrace 1 .

 Fully tighten and check that
the wheel is horizontally l ush
against the rear l oor .

 Close the l ap using the lug to
lock the winch.

 Store the rest of the tools in the
right-hand trim of the boot.
For your safety, always
change the wheel:
- on level, stable, non-slippery ground,
- with the handbrake on and the ignition switched off,
- with i rst or reverse gear engaged (position P for the automatic
gearbox),
- with the vehicle chocked.

Never go underneath a vehicle that
is supported only by a jack (use a
ramp).

Never rei t the holder under the
vehicle without the spare wheel.

Do not use a screwdriver in place
of the wheelbrace to unwind or
wind the winch. Recommendations when using
the temporary spare wheel *
Your vehicle may be equipped with a
spare wheel which has a different rim
to the standard wheel.
After use, it must be replaced as
quickly as possible.
Observe the following instructions to
avoid altering the behaviour of the
vehicle:
-
do not exceed
50 mph (80 km/h) ,
- do not i t a wheel trim,
- drive with care,
- check the tyre pressure indicated
on the label.
After changing the wheel:
- have the correct positioning of the
punctured wheel, the tightening
of the bolts and the tyre pressure
checked by a PEUGEOT dealer
as soon as possible,
- have the punctured tyre repaired and rei t it to the vehicle as soon
as possible,
- have the correct positioning of the spare wheel checked by a
PEUGEOT dealer.
Wheels i tted with the Tyre Under-
Inl ation Detection system
For further information refer to "Tyre
under-inl ation detection" in the
safety section.
* According to model and country.

10PRACTICAL INFORMATION
123
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool 6 to remove the
trims before slackening the bolts. Wheel with centre trim
Fitting snow tyres
If you i t snow tyres mounted on
steel wheels onto your vehicle, it
is essential to use special bolts
available from your PEUGEOT
dealer.
 slide the trim remover 7 into the
notch of the centre trim,

 use the trim remover as a lever
pressing on the trim to unclip it,

 unscrew the bolt using the anti-
theft socket and the wheelbrace.
If your vehicle is i tted with a steel
spare wheel, when i tting it, it is

normal when tightening the bolts to
notice that the washers do not come
into contact with the rim. The spare
wheel is secured by the cone shape
of each bolt.
This anti-theft socket was
given to you on delivery
of your vehicle along with
the duplicate keys and the
coni dential card.
Make a careful note of the code
number engraved on the head of the
anti-theft socket. This will enable you
to obtain a duplicate socket from a
PEUGEOT dealer.
Special features of alloy wheels
Fitting the spare wheel
Anti-theft bolts
Your wheels are i tted with an anti-
theft bolt, one per wheel.
Bolt covers
Wheel with chrome trim

 remove the chrome trim,

 unscrew the bolt using the anti-
theft socket and the wheelbrace.

10PRACTICAL INFORMATION
124
Front lights
In the engine compartment, on the
right-hand side, remove the style
trim * :
- press the centre of each plastic stud A ,
- remove each plastic stud,
- remove the style trim.
When you have i nished, do not
forget to put everything back in place
correctly:
- position the style trim * ,
- rei t each plastic stud A by
pressing on it. Handle the bulbs with a dry
cloth.
The headlamps are i tted
with polycarbonate glass with
a protective coating. Do not clean
them with a dry or abrasive cloth,
nor with a detergent or solvent
product.
Use a sponge and soapy water.
1. Dipped beam headlamps
(H1-55 W or xenon bulb).

WARNING: RISK OF ELECTRO-
CUTION
Xenon bulbs must be changed by a
PEUGEOT dealer.
2. Main beam headlamps (H7-55 W).

 Remove the protective cover
corresponding to the faulty bulb.

 Disconnect the connector.

 Press the end of each securing
clip. Change the bulb.
When i tting the new bulb, ensure that the direction notches are
positioned correctly and the
securing clips are i xed properly.
 Reconnect the connector.

 Rei t the protective cover.
CHANGING A BULB
* According to engine.

10PRACTICAL INFORMATION
125
Integrated direction indicator side
repeaters.

 Push the repeater forwards and
release it.

 Remove the repeater and change
it.
These can be obtained from a
PEUGEOT dealer.
Amber coloured bulbs, such
as the direction indicators,
must be replaced with bulbs
of identical specii cation and
colour.

3. Side lights (W 5 W).

 Remove the protective cover
corresponding to the faulty bulb.

 Disconnect the connector.

 Remove the bulb and change it.
4. Direction indicators (PY 21 W amber).

 Turn the bulb holder a quarter of
a turn and remove it.

 Change the bulb.

Note
: in certain climatic conditions
(low temperature, humidity), conden-
sation inside the headlamp glass is
normal ; it disappears a few minutes
after the lights are switched on.
5. Fog lamps (H11-55 W).
Contact a PEUGEOT dealer to have
these bulbs changed.

10PRACTICAL INFORMATION
126

1. Direction indicators (P 21 W).

2. Reversing lights (P 21 W),
left-hand side.
Fog lamp (P 21 W), right-hand
side.

3. Brake lights (P 21 W).

4. Side lights (x 2) (R 5 W).
 Using a 10 mm box spanner,
unscrew the 2 i xing nuts 1 .

 Release the lamp unit by pushing
it outwards.

 Squeeze the two tabs 2 to release
the bulb holder.

 Change the faulty bulb.

 When rei tting, ensure that the
lamp unit seal has been put back
in place correctly.
These 6 bulbs are changed from
inside the boot:

 Move aside the boot trim to
access the bulb holder,

 Press the two tabs and remove
the bulb holder,

 Change the faulty bulb.
When rei tting, take care to pass the
trim under the seal.
Rear lights (saloon) Third brake light (saloon)
(4 W 5 W bulbs)