Peugeot 308 SW BL 2010.5 - RHD (UK. Australia) Manual Online

Page 81 of 336

!
79
ACCESS
Deadlocking renders the exterior
and interior door controls inopera-
tive.
It also deactivates the manual cen-
tral control button.
Therefore, never leave anyone
inside the vehicle when it is dead-
locked.






Deadlocking using the remote
control

Deadlocking using the key

)
Short press on the closed
padlock to lock the vehicle
or
Deadlocking is confi rmed by fi xed light-
ing of the direction indicators for ap-
proximately two seconds.
According to version, the door mirrors
fold at the same time.

)
Turn the key to the right in the driver's
door lock to lock the vehicle.

)
Turn the key to the right again
within fi ve seconds to deadlock the
vehicle.


Folding the key


)
First press this button to fold the key.









Locating your vehicle

This function allows you to identify your
vehicle from a distance, particularly in
poor light. Your vehicle must be locked.

Electronic engine immobiliser
The key contains an electronic chip
which has a special code. When the
ignition is switched on, this code must
be recognised in order for starting to be
possible.
This electronic engine immobiliser locks
the engine management system a few
minutes after the ignition is switched off
and prevents starting of the engine by
anyone who does not have the key.












Anti-theft protection

In the event of a malfunction,
you are informed by lighting of
this warning lamp, an audible
signal and a message on the
multifunction screen.
In this case, your vehicle does not start;
contact a PEUGEOT dealer as soon as
possible.

)
Long press on the closed padlock to
lock the vehicle and also close the
windows (depending on version).

)
Short press on the closed padlock
again within fi ve seconds to deadlock
the vehicle.



)
Press the closed padlock
on the remote control.
This will switch on the courtesy lamps
and the direction indicators will fl ash for
a few seconds.

Page 82 of 336

i
!
80
ACCESS









Starting the vehicle



)
Insert the key in the ignition switch.
The system recognises the starting
code.

)
Turn the key fully towards the
dashboard to position 3 (Starting)
.

)
When the engine starts, release the
key.



Switching the vehicle off



)
Immobilise the vehicle.

)
Turn the key fully towards you to
position 1 (Stop)
.

)
Remove the key from the ignition
switch.

















Remote control problem

Following disconnection of the vehicle
battery, replacement of the remote con-
trol battery or in the event of a remote
control malfunction, you can no longer
unlock, lock or locate your vehicle.


)
First of all, use the key in the lock to
unlock or lock your vehicle.

)
Then, reinitialise the remote control.
If the problem persists, contact a
PEUGEOT dealer as soon as possible.
Changing the battery
Battery ref.: CR1620/3 volts.

Reinitialisation


)
Switch off the ignition.

)
Turn the key to position 2 (Ignition)
.

)
Press the closed padlock immedi-
ately for a few seconds.

)
Switch off the ignition and remove
the key from the ignition switch.
The remote control is fully operational
again. If the battery is fl at, you are in-
formed by lighting of this warn-
ing lamp, an audible signal and
a message on the multifunction
screen. This replacement battery is available
from PEUGEOT dealers.






Key left in the "Ignition on"
position
If the key has been left in the ig-
nition switch, the ignition will be
switched off automatically after
one hour.
To switch the ignition back on, turn
the key to position 1 (Stop)
, then
back to position 2 (Ignition

on

)
.


)
Unclip the casing using a coin at the
notch.

)
Slide the fl at battery out of its
location.

)
Slide the new battery into its location
observing the original direction.

)
Clip the casing.

)
Reinitialise the remote control.


A heavy object (key fob...), attached
to the key and weighing down on
its shaft in the ignition switch, could
cause a malfunction.

Page 83 of 336

!
81
ACCESS














Lost keys

Visit a PEUGEOT dealer with the vehicle's V5 registration document and your
personal identifi cation documents.
The PEUGEOT dealer will be able to retrieve the key code and the transponder
code required to order a replacement key.







Do not throw the remote control bat-
teries away, they contain metals which
are harmful to the environment.
Take them to an approved collection
point.

Remote control

The high frequency remote control is a sensitive system; do not operate it
while it is in your pocket as there is a possibility that it may unlock the vehicle,
without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range and
out of sight of your vehicle. You run the risk of stopping it from working and the
remote control would have to be reinitialised.
The remote control does not operate when the key is in the ignition, even
when the ignition is switched off, except for reinitialisation.


Locking the vehicle

Driving with the doors locked may make access to the passenger compartment
by the emergency services more diffi cult in an emergency.
As a safety precaution (with children on board), remove the key from the
ignition when you leave the vehicle, even for a short time.


Anti-theft protection

Do not make any modifi cations to the electronic engine immobiliser system;
this could cause malfunctions.


When purchasing a second-hand vehicle

Have the key codes memorised by a PEUGEOT dealer, to ensure that the
keys in your possession are the only ones which can start the vehicle.

Page 84 of 336

!
i
82
ACCESS
ALARM
System which protects and provides a
deterrent against theft and break-ins.
It provides the following types of moni-
toring.


Locking the vehicle with full
alarm system
For all work on the alarm system,
contact a PEUGEOT dealer.
Activation


)
Switch off the ignition and get out of
the vehicle.

)
Press the locking button on the
remote control.
The monitoring system is active: the in-
dicator lamp on the button fl ashes once
per second.
After the locking button on the remote
control is pressed, the exterior perime-
ter monitoring is activated after a delay
of 5 seconds and the interior volumetric
monitoring after a delay of 45 seconds.
- Exterior perimeter
The system checks for opening of the
vehicle.
The alarm is triggered if anyone tries to
open a door, the boot, the bonnet...



- Interior volumetric
The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks
a window, enters the passenger com-
partment or moves inside the vehicle.



Self-protection function
The system checks for the putting out of
service of its components.
The alarm is triggered if the battery, the
central control or the wires of the siren
are put out of service or damaged.
Deactivation


)
Press the unlocking button on the
remote control.
The alarm system is deactivated: the
indicator lamp on the button switches off.
If an opening (door, boot...) is
not closed fully, the vehicle is not
locked but the exterior perimeter
monitoring will be activated after a
delay of 45 seconds at the same
time as the interior volumetric
monitoring.

Page 85 of 336

!
i
83
ACCESS

Triggering of the alarm

The monitoring functions remain
active until the alarm has been trig-
gered eleven times in succession.
When the vehicle is unlocked using
the remote control, rapid fl ashing
of the indicator lamp on the button
informs you that the alarm was trig-
gered during your absence. When
the ignition is switched on, this
fl ashing stops immediately.



Failure of the remote control

To deactivate the monitoring functions:



)
Lock or deadlock the vehicle using
the key in the driver's door lock.




Locking the vehicle without
activating the alarm

When the ignition is switched on, fi xed
lighting of the indicator lamp on the button
indicates a malfunction of the system.
Have it checked by a PEUGEOT dealer.

This is indicated by sounding of the siren
and fl ashing of the direction indicators
for thirty seconds.


)
Unlock the vehicle using the key in
the driver's door lock.

)
Open the door; the alarm is
triggered.

)
Switch on the ignition; the alarm
stops. The indicator lamp on the
button switches off.




Malfunction

Automatic activation *

To be effective, this deactivation
must be carried out each time the
ignition is switched off.
Deactivation of the interior
volumetric monitoring


)
Switch off the ignition.

)
Within ten seconds, press the but-
ton until the indicator lamp is lit con-
tinuously.

)
Get out of the vehicle.

)
Press the locking button on the
remote control immediately.
The exterior perimeter monitoring alone
is activated: the indicator lamp on the
button fl ashes once per second.


Locking the vehicle with
exterior perimeter monitoring
only
Deactivate the interior volumetric moni-
toring to avoid unwanted triggering of
the alarm in certain cases such as:


- leaving a pet in the vehicle,

- leaving a window partially open,

- washing your vehicle.
Reactivation of the interior
volumetric monitoring


)
Press the unlocking button on the
remote control to deactivate the
exterior perimeter monitoring.

)
Press the locking button on the
remote control to activate all the
monitoring functions.
The indicator lamp on the button again
fl ashes once per second.


*
According to country.
2 minutes after the last door or the boot
is closed, the system is activated auto-
matically.


)
To avoid triggering the alarm on
entering the vehicle, fi rst press the
unlocking button on the remote
control.

Page 86 of 336

i
i
!
84
ACCESS
The electric window controls re-
main operational for approximately
45 seconds after the ignition is
switched off or until the vehicle is
locked after a door is opened.
If one of the passenger windows
cannot be operated from the driver's
door control panel, carry out the
operation from the control panel
of the passenger door concerned,
and vice versa.
ELECTRIC WINDOWS
Fitted with a safety anti-pinch system
and a deactivation system to prevent
misuse of the rear controls.


1.
Driver's electric window control.


2.
Passenger's electric window
control.


3.
Rear right electric window
control.


4.
Rear left electric window control.


5.
Deactivation of the rear electric
window and door controls.

If the window cannot be closed (for
example, in the presence of ice),
immediately after the movement is
reversed:


)
press and hold the control until
the window opens fully,

)
then pull the control immediately
and hold it until the window
closes,

)
continue to hold the control for
approximately one second after
the window has closed.

The safety anti-pinch function
is not operational during these
operations.


Safety anti-pinch
When the window rises and meets an
obstacle, it stops and partially lowers
again.
- automatic mode



)
Press or pull the control fi rmly.
The window opens or closes fully
when the control is released.

)
Pressing the control again stops
the movement of the window.



One-touch electric windows

There are two options:


- manual mode



)
Press or pull the control gently.
The window stops when the con-
trol is released. After approximately ten consecutive
complete opening/closing move-
ments of the window, a protection
function is activated which only
authorises closing of the window to
prevent damage to the electric win-
dow motor.
Once the window is closed, the con-
trols will become available again
after approximately 40 minutes.

Page 87 of 336

!
i
!
85
ACCESS
This control also deactivates the
interior controls for the rear doors
(refer to the section "Child safety -
§ Electric child lock").
Any other status of the indicator
light indicates a malfunction of the
electric child lock. Have it checked
by a PEUGEOT dealer.
Reinitialisation
If a window does not rise automatically,
its operation must be reinitialised:


)
pull the control until the window
stops,

)
release the control and pull it again
until the window closes fully,

)
continue to hold the control for
approximately one second after the
window has closed,

)
press the control to lower the window
automatically to the low position,

)
when the window has reached the
low position, press the control again
for approximately one second. Always remove the key from the
ignition when leaving the vehicle,
even for a short time.
If an obstacle is encountered during
operation of the electric windows,
you must reverse the movement of
the window. To do this, press the
control concerned.
When the driver operates the con-
trols for the passengers' electric
windows, they must ensure that no
one is preventing correct closing of
the windows.
The driver must ensure that the
passengers use the electric win-
dows correctly.
Be aware of children when operating
the windows.


Deactivation of the rear electric
window and door controls


)
For the safety of your children, press
control 5
to deactivate the rear
electric window controls regardless
of their position.
Indicator lamp on, the rear controls are
deactivated.
Indicator lamp off, the rear controls are
activated.
The safety anti-pinch function is not
operational during these operations.


Page 88 of 336

!
86
ACCESS
DOORS


)
After unlocking the vehicle com-
pletely using the remote control or
the key, pull the door handle.



From inside


)
Pull on the front door control to open
the door; this unlocks the vehicle
completely.

)
Pull on the rear door control to
open the door; this unlocks the door
concerned only.




Closing

When a door is not closed correctly:


-
when the engine is running
,
this warning lamp comes on,
accompanied by a message
on the multifunction screen
for a few seconds,

- when the vehicle is moving
(speed
higher than 6 mph (10 km/h)), this
warning lamp comes on, accompanied
by an audible signal and a message
on the multifunction screen for a
few seconds.


Opening


From outside


Version with deadlocking
The interior door controls do not
operate when the vehicle is dead-
locked.

Page 89 of 336

i
!
i
87
ACCESS
If the vehicle is locked or dead-
locked from the outside, the red in-
dicator lamp fl ashes and button A

is inactive.


)
In this case, use the remote
control or the key to unlock the
vehicle.


If one of the doors is open, the auto-
matic central locking does not take
place.
If the boot or the rear screen is
open, the automatic central locking
of the doors is active.













Manual centralised control

System which provides full manual
locking or unlocking of the doors from
the inside.

Locking


)
Press button A
to lock the vehicle.
The red indicator lamp on the button
comes on.

Automatic centralised control

System which provides full automatic
locking or unlocking of the doors, the
boot and the rear screen while driving.
You can activate or deactivate this
function.
Activation


)
Press button A
for more than
two seconds.
A confi rmation message appears on the
multifunction screen, accompanied by
an audible signal.

Unlocking


)
Above 6 mph (10 km/h), press but-
ton A
to unlock the doors, the boot
and the rear screen temporarily.
If one of the doors is open, the cen-
tral locking from the inside does not
take place.

Unlocking


)
Press button A
again to unlock the
vehicle.
The red indicator lamp on the button
switches off.
Locking
When the speed exceeds 6 mph
(10 km/h), the doors, the boot and the
rear screen lock automatically.

Deactivation


)
Press button A
again for more than
two seconds.
A confi rmation message appears on the
multifunction screen, accompanied by
an audible signal.

Page 90 of 336

88
ACCESS






Emergency control

To lock or unlock the doors manually in
the event of a malfunction of the central
locking system or battery failure.


)
On the rear doors, check that the
child lock is not activated.

)
Remove the black cap, located on
the edge of the door, using the key.

)
Insert the key in the socket without
forcing it, then without turning it,
move the latch sideways towards
the inside of the door

)
Remove the key and refi t the cap.



Opening



)
After unlocking the vehicle using the
remote control or the key, pull the
handle and raise the tailgate.

BOOT



- when the engine is running
,
this warning lamp comes on,
accompanied by a message
on the multifunction screen
for a few seconds,

- when the vehicle is moving
(speed
above 6 mph (10 km/h)), this warning
lamp comes on, accompanied by
an audible signal and a message
on the multifunction screen for a
few seconds.








Tailgate release

System for mechanical unlocking of the
boot in the event of a battery or central
locking malfunction.

Unlocking


)
Fold back the rear seats to gain
access to the lock from inside the
boot.

)

Insert a small screwdriver into hole A

of the lock to unlock the tailgate.


Locking the driver's door


)
Insert the key in the lock, then turn it
to the rear.


Unlocking the driver's door


)
Insert the key in the lock, then turn it
to the front.


Locking the front and rear
passenger doors
Unlocking the front and rear
passenger doors


)
Pull the interior door opening control.




Closing



)
Lower the tailgate using the interior
grab handle. If the tailgate is not closed correctly:

Page:   < prev 1-10 ... 41-50 51-60 61-70 71-80 81-90 91-100 101-110 111-120 121-130 ... 340 next >