Peugeot 407 C Dag 2008 Service Manual

3
42
Front visibility
control (7)
In certain cases, the comfort pro-
gramme may not be suffi cient to dem-
ist or de-ice the windows (humidity,
several passengers, ice).

 In this case, select the front vis-
ibility programme in order to clear
the windows quickly. The indicator
light comes on.
It controls the air conditioning, air fl ow
and intake and distributes the ventila-
tion to the windscreen and front side
windows.
The front visibility control symbol is
displayed on the multifunction display.
Once the inconvenience has been
eliminated, pressing button 1 returns
the system to the comfort setting. Intake of exterior
air/Recirculation of
interior air (8)
This function enables you to isolate
the passenger compartment from ex-
terior fumes and odours.

 Press button 8 several times to
set the air intake mode, the indica-
tor light which corresponds to the
mode set comes on at your prefer-
ence:
- intake of exterior air. Forced ex- terior air intake mode.
- recirculation of the air inside the passenger compartment.
The indicator light which corre- sponds to the mode set comes
on. Prolonged operation in inte-
rior air recirculation mode may
result in the formation of con-
densation and deterioration of
the quality of the interior air.
Do not drive in air recirculation
mode for prolonged periods, ex-
cept in truly exceptional atmo-
spheric conditions.
The message associated with
the control is displayed on the
multifunction display.

 Press button 8 to return to auto-
matic control of the air intake. The
indicator lights are switched off.

For your comfort, when the ignition is
switched off, the settings are stored
until it is switched on again. Rear screen
demisting (9)
The heated rear screen operates inde-
pendently of the air conditioning system.

 Press button 9 , with the engine
running, to demist the rear screen
and the mirrors. The indicator light
comes on.
Demisting is switched off automatically
to avoid an excessive consumption of
current and in relation to the exterior
temperature.
It may be stopped by pressing button 9
again or when the engine is switched off.
However, the demisting resumes if the
engine is switched on again within one
minute.
Switch off the rear screen and exterior
mirrors demisting when you consider
this necessary as low current consump-
tion reduces fuel consumption.

3
43
Deactivation of the air conditioning
(A/C-OFF)
Deactivation or activation of the
simultaneous Left-Right control
Activation of this function permits the
transfer of the driver's confi guration to
the passenger.
Deactivation of this function permits a
return to the independent driver/pas-
senger settings.
Any manual action on button 4 or 6
cancels the simultaneous confi gura-
tion setting.
"AIR CON" menu
Press the "MENU" but-
ton to gain access to
the general menu, then
confi rm.
The "General menu" appears on the
multifunction display.
Select the Air Conditioning icon using
the navigator buttons.
The "Air Conditioning" menu ap-
pears on the multifunction display as
the main display.
Additional heating *
Vehicles which are fi tted with an HDI
engine may be equipped with auto-
matic additional heating to improve
your comfort.
When the engine is idling or when the
vehicle is stationary, a high-pitched
whistling noise and the emission of a
small amount of smoke and odour is
normal.
* According to country.
Deactivation may result in discomfort
(temperature, humidity, odour, con-
densation).
You can cancel the deactivation by
pressing the
"AUTO" button on the air
conditioning control panel.

3
44
PROGRAMMABLE HEATING Programming remote control
The heating system programming
remote control consists of the following
buttons and displays:

1. Scrolling functions menu buttons.

2. Function indicator lights: clock,
temperature, operating time, pro-
grammed time, heater operation,
heating management symbols.

3. Digital displays: time, temperature,
duration of operation, programmed
time or level of heating.

4. Off button.

5. On button.
Displaying the functions

If a malfunction of the programma-
ble heating system occurs, contact
a PEUGEOT dealer.
The programmable heating operates
independently of the engine.
When the engine is off, it pre-heats
the coolant circuit in order to benefi t
from an optimum engine operating
temperature from the time the engine
is switched on.
The programmable heating system is
switched on using the long range remote
control. Activation can be immediate or
deferred by means of a programming
function.
screen
Press the buttons
1 in succession to
display the functions.
The fi rst press of the left-hand or right-
hand button displays the time.
Next, the left-hand button permits
access to the programming time then
to the level of heating (C1 to C5).
The right-hand button permits access
to the passenger compartment tempe-
rature then to the duration of operation
of the heater if it is to be switched on
immediately.
The passenger compartment
temperature information is only
available when the engine is
off.

3
45
Once the time has been displayed, by
means of the buttons 1 , press buttons 4
and 5 simultaneously within 10 seconds.
This symbol fl ashes.
Setting the time
Set the time using the buttons 1 .
Press buttons 4 and 5 simultaneously
to save it.
This symbol is displayed (fi xed). Press button
5 (ON) until the message

"OK" appears.
When the signal has been received,
the message "OK" is displayed along
with the duration of operation.
The heater starts and this symbol
is displayed.
Immediate activation
To deactivate the function, press but-
ton 4 (OFF) until the message "OK"
appears.
When carrying out these oper-
ations, if the message "FAIL"
appears, the signal has not
been received. Repeat the
procedure after changing your
location.
This symbol is switched off.
Setting the duration of operation
Press the buttons
1 to display the du-
ration of operation.
This symbol is displayed.
Once the duration of operation has
been displayed, press buttons 4 and 5
simultaneously within 10 seconds.
This symbol fl ashes.
Set the duration by pressing the but-
tons 1 (adjustment in steps of 10 mins
and max value 30 mins).
Press buttons 4 and 5 simultaneously
to save the duration of operation.
This symbol is displayed (fi xed).
The factory setting value is
30 minutes.

3
46
You must programme your departure
time in order for the system to calculate
the optimum heater start time automati-
cally.
Programming the heating
Set the time by pressing the buttons 1
and press buttons 4 and 5 simultane-
ously to save it.
Programming the departure time
Press the buttons
1 to display the pro-
gramming time.
This symbol is displayed.
Once the programming time has been
displayed, press buttons 4 and 5 simul-
taneously within 10 seconds.
This symbol fl ashes.
This symbol is displayed (fi xed). Once the programming time has been
displayed by means of the buttons
1 ,
press button 5 (ON) until the message

"OK" appears.
Activation - deactivation
When the signal has been received,
the message
"OK" is displayed
along with the symbol "HTM" .

To deactivate the programming, press
button 5 (OFF) until the message

"OK" appears.
HTM: Heat Thermo Management.
The symbol "HTM" is switched off.
When carrying out these opera-
tions, if the message "FAIL" ap-
pears, the signal has not been
received. Repeat the procedure
after changing your location.
This symbol is displayed when
the heater starts.
Switching off the heating
Press button
5 (ON).
The symbol "HTM" remains on.
Changing the level of heating
The system offers 5 levels of heating
(from the lowest level C1 to the high-
est level C5 ).
Once the level of heating has been
displayed by means of the buttons 1 ,
press buttons 4 and 5 simultaneously.
The letter "C" fl ashes.
Set the level of heating by pressing
the buttons 1 .
Press buttons 4 and 5 simultaneously
to save the level selected. The letter

"C" is displayed (fi xed).
The factory pre-sets are re-
placed by the new settings en-
tered. The programmed times
are stored until the next time
they are changed.
When the departure time is acti-
vated, the level of heating cannot be
changed. The departure time must be
deactivated fi rst.

3
Always switch off the programmable
heating while fi lling with fuel to avoid
any risk of fi re or explosion.
To avoid any risk of poisoning and as-
phyxiation, the programmable heat-
ing must not be used, even for short
periods, in an enclosed space such
as a garage or workshop which is not
equipped with an exhaust gas extrac-
tion system.
Do not park the vehicle on an infl am-
mable surface (dry grass, dead leaves,
paper…), there is a risk of fi re.
The programmable heating system
is supplied by the vehicle's fuel tank.
Before use, ensure that the quantity of
fuel remaining is suffi cient. If the fuel
tank is at the reserve, we strongly ad-
vise that you do not programme the
heating.
Changing the battery
The remote control is supplied by a 6 V -
28 L battery, which is supplied.
Information on the display indicates
when it is time to replace this battery.
Unclip the casing then replace the battery.
The remote control must then be reini-
tialised, see below.
Do not discard the used batteries, take
them to an approved collection point. Reinitialising the remote
control
If the vehicle's battery is dis-
connected or the remote con-
trol's battery is replaced, the remote
control must be reinitialised.
After switching on the power, press
button 4 (OFF) for 1 second within the
next 5 seconds. If the operation has
taken place correctly the message

"OK" is displayed on the remote con-
trol screen.
If a problem occurs, the message

"FAIL" appears. Repeat the operation.
As an accessory, your programmable
heating can be adapted to pre-heat
your vehicle's passenger compart-
ment.

3
48
EXTERIOR MIRRORS
Automatic tilting of the mirrors in reverse gear *
This function allows you to see the
ground (kerb, wall...) when carrying
out parking manoeuvres in reverse
gear. Objects observed in the driver
and passenger mirrors are, in
reality, closer than they appear.
This must be taken into account in
order to judge the distance of vehicles
approaching from behind correctly.
Adjustment

 Move control A to the right or to
the left to select the corresponding
mirror.

 Direct control B in all four directions
to adjust .
Folding back the mirrors electrically
- from inside:
 With the ignition on, move the
control A to the central position
then pull it rearwards.
- from outside:


Lock the vehicle using the remote
control.
This function can be deactivated.
Consult a PEUGEOT dealer.
When the vehicle is parked, the exterior
mirrors can be folded back manually. Initial setting of the function
Engage reverse gear then select and ad-
just the left mirror then the right mirror.
These settings will be stored.
Tilting the mirror to the parking
position

 engage reverse gear,

 move control A to the right or the left
to select the corresponding mirror.
The exterior mirror corresponding to
the side on which you are parking tilts
downwards.
Intentional returning of the mirror to
the driving position:

 deselect the mirror.

 change out of reverse gear. After a
few seconds, the glass of the corre-
sponding mirror resumes its normal
position.
The mirror returns to the driving posi-
tion automatically if the vehicle speed
exceeds 6 mph (10 km/h) or if the en-
gine is switched off.
* According to version.

3
49
Operation
Switch on the ignition and press switch 1 :
- Indicator light 2 lit (switch pressed):
automatic operation.
- Indicator light 2 off: automatic sys-
tem off. The mirror remains at its
most clear. Manual interior mirror
The interior mirror has two positions:
- day (normal),
- night (anti-dazzle).
To change from one to the other, push
or pull the lever on the lower edge of
the mirror.
Special feature
To ensure maximum visibility
during manoeuvres, the mirror
clears automatically when re-
verse gear is engaged.
Automatic day/night interior mirror
This automatically and gradually
changes between the day and night
positions. To prevent dazzling, the
glass of the mirror darkens automati-
cally depending on the intensity of the
light from behind. It clears as the light
(headlamps of following vehicles, sun-
light) decreases, ensuring maximum
visibility.
INTERIOR MIRROR

3
50
ELECTRIC ADJUSTMENT OF THE HEIGHT AND DEPTH OF THE STEERING WHEEL
When stationary, adjust the height or
depth of the steering wheel by moving
the control:

 forwards or backwards to adjust
the depth.

 up or down to adjust the height.
You can activate or deac-
tivate this function via the
"personalisation-configu-
ration" menu on the multi-
function display.
WELCOME FUNCTION
When the driver's door is opened with
the ignition off, the steering wheel ris-
es to make access to or exit from the
vehicle easier. MANUAL STEERING WHEEL HEIGHT AND DEPTH ADJUSTMENT
When the vehicle is stationary, unlock
the steering wheel by pushing the con-
trol forwards.
Adjust the height and depth of the
steering wheel then lock by pulling the
control fully.
Reinitialisation
Following reconnection of the battery, the
welcome function must be reinitialised:
- move the control in the direction of the required adjustment,
- release the control,
- move the control again until it reaches its stop.
This procedure must be carried out for
all four directions.

3
51
MANUAL FRONT SEATS
Longitudinal adjustment
Lift the control bar and slide the seat
forwards or backwards. Driver and passenger seat cushion
height and angle adjustment
Pump up or down to the required position.
Seat back angle adjustment
Without resting your back against the
seat, turn the control to adjust the angle
of the seat back.