ECO mode PONTIAC G6 2007 Owners Manual

DRIVE (D):This position is for normal driving. It
provides the best fuel economy for your vehicle. If
you need more power for passing, and you are:
Going less than 35 mph (55 km/h), push
your accelerator pedal about halfway down.
Going about 35 mph (55 km/h) or more, push
the accelerator all the way down.
You will shift down to the next gear and have
more power.
Downshifting the transaxle in slippery road
conditions could result in skidding, see “Skidding”
underLoss of Control on page 271.
Notice:If your vehicle seems to accelerate
slowly or not shift gears when you go faster,
and you continue to drive your vehicle that way,
you could damage the transaxle. Have your
vehicle serviced right away. You can drive in
LOW (L) when you are driving less than 35 mph
(55 km/h) and DRIVE (D) for higher speeds
until then.THIRD (3):This position, available on the SE
model, is also used for normal driving. However,
it reduces vehicle speed more than DRIVE (D)
without using your brakes. Here are some times
you might choose THIRD (3) instead of DRIVE (D):When driving on hilly, winding roads.
When towing a trailer, so there is less shifting
between gears.
When going down a steep hill.
LOW (L):This position, available on the SE model,
reduces vehicle speed more than THIRD (3)
without using your brakes. You can use LOW (L) on
hills. It can help control your speed as you go down
steep mountain roads, but then you would also
want to use your brakes off and on.
131

The transaxle will only allow you to shift into gears
appropriate for the vehicle speed and engine
revolutions per minute (RPM):
The transaxle will not automatically shift to the
next higher gear if the engine RPM is too high.
The transaxle will not allow shifting to the next
lower gear if the engine RPM is too high.
If the vehicle does not respond to a gear change, or
detects a problem with the transaxle, the range of
gears may be reduced and the Malfunction
Indicator Lamp will come on. SeeMalfunction
Indicator Lamp on page 204for more information.
SECOND (2)/THIRD (3)
Gear Start Feature
Notice:If you attempt a third gear start while
trailering or towing a heavy load, you will notice
reduced engine power. This could overheat and
damage your transaxle. Do not attempt a third
gear start while trailering or towing your
vehicle.If your vehicle has the 6-speed transaxle, when
accelerating your vehicle from a stop in snowy
and icy conditions, you may want to shift into
SECOND (2), or THIRD (3) gear. A higher gear,
and light application of the gas pedal, may allow
you to gain more traction on slippery surfaces.
With the TAP-Shift feature, the vehicle can
accelerate from a stop in SECOND (2) or
THIRD (3).
1. Move the shift lever from DRIVE (D) into the
MANUAL MODE (M) position.
2. With the vehicle stopped, press the plus (+)
paddle forward to select SECOND (2) or
THIRD (3)gear. The vehicle will start
from a stop position in SECOND (2) or
THIRD (3)gear.
3. Once the vehicle is moving select the desired
drive gear.
133

Temperature Control:Turn the center knob
clockwise or counterclockwise to increase
or decrease the temperature inside your vehicle.
When it’s cold outside 0°F (−18°C) or lower,
use the engine coolant heater, if the vehicle has
one, to warm air faster in your vehicle. An
engine coolant heater warms the engine coolant
that is used to warm the inside of your vehicle. For
more information, seeEngine Coolant Heater on
page 128.
#(Air Conditioning):Press this button to turn
the air conditioning system on or off. When
the air conditioning button is pressed, an indicator
light comes on to indicate that the air conditioning
is activated.
The air conditioning system removes moisture from
the air, so sometimes a small amount of water drips
underneath the vehicle while it is idling or after the
engine is turned off. This is normal.
Maximum Air Conditioning
On hot days, open the windows to let hot inside
air escape; then close them. This helps to reduce
the time it takes for your vehicle to cool down.
It also helps the system to operate more efficiently.For quick cool down on hot days, do the following:
1. Select the
Cvent mode.
2. Select the highest fan speed.
3. Select
#air conditioning.
4. Select the
?recirculation mode.
5. Select the coolest temperature.
Using these settings together for long periods of
time can cause the air inside of your vehicle
to become too dry. To prevent this from
happening, after the air in your vehicle has cooled,
turn the recirculation mode off.
If your vehicle has the remote start feature, it will
turn on using the last settings selected on the
climate control before the vehicle was turned off.
The fan and air delivery knobs can be used during
remote start. The buttons will not work until the
ignition is turned on by the key.
The climate control system changes back to
manual operation when the vehicle key is
turned to ON.
184

Operation Tips
Clear away any ice, snow or leaves from the
air inlets at the base of the windshield that
may block the ow of air into your vehicle.
Use of non-GM approved hood deectors may
adversely affect the performance of the system.
Keep the path under the front seats clear of
objects to help circulate the air inside of your
vehicle more effectively.
When an objectionable odor outside the vehicle
is encountered, use the recirculation mode,
with the temperature knob at a comfortable
setting to prevent the odor from entering the
vehicle through the ventilation system. This can
be helpful when driving through a long tunnel
with poor ventilation. However, extended usage
of this mode in cold or cool weather can cause
window fogging.
Warning Lights, Gages, and
Indicators
This part describes the warning lights and gages
that may be on your vehicle. The pictures will
help you locate them.Warning lights and gages can signal that
something is wrong before it becomes serious
enough to cause an expensive repair or
replacement. Paying attention to your warning
lights and gages could also save you or others
from injury.
Warning lights come on when there could be or
there is a problem with one of your vehicle’s
functions. As you will see in the details on the next
few pages, some warning lights come on briey
when you start the engine just to let you know they
are working. If you are familiar with this section,
you should not be alarmed when this happens.
Gages can indicate when there could be or there is
a problem with one of your vehicle’s functions.
Often gages and warning lights work together to let
you know when there is a problem with your
vehicle.
When one of the warning lights comes on and
stays on when you are driving, or when one of the
gages shows there may be a problem, check
the section that tells you what to do about
it. Follow this manual’s advice. Waiting to do
repairs can be costly — and even dangerous. Get
to know your warning lights and gages. They
are a big help.
192

Driver Information Center (DIC)
The Driver Information Center (DIC) provides
the following:
A way to personalize your vehicle
Trip information
Warning messages
The buttons used to activate the DIC are located
on the left side of the vehicle’s audio system.
INFO/
4(Information):Press this button to scroll
through the vehicle information mode displays.
MENU:Press this button to enter and scroll
through the menu mode.ENTER/
r(Enter):Press this button to select a
menu option or to acknowledge a warning
message.
The DIC messages will be read through your
audio system display.
DIC Operation and Displays
The DIC comes on when the ignition is ON. If your
vehicle has the uplevel audio system, the time
and outside temperature is shown on the rst line
of the display and the DIC information is shown
on the second line of the display.
The DIC has different modes which can be
accessed by pressing the DIC buttons. The button
functions are detailed in the following section.
United StatesCanada
209

Information Mode
INFO/4(Information):Press this button to scroll
through the vehicle information mode displays
in the following order:
TRIP A
TRIP B
FUEL RANGE (Fuel Range Until Empty)
ECON (Average Fuel Economy)
AV SPEED (Average Vehicle Speed)
OIL LIFE (Engine Oil Life System)
TRIP A or TRIP B:Press the information button
until TRIP A or TRIP B is displayed. This
shows the current distance traveled since the last
reset for each trip odometer in either miles (mi)
or kilometers (km). Both odometers can be used at
the same time. Each trip odometer can be reset
to zero separately by pressing and holding
the enter button for a few seconds while the
desired trip odometer is displayed.FUEL RANGE:Press the information button until
FUEL RANGE is displayed. This shows the
remaining distance you can drive without refueling.
It is based on fuel economy and the fuel
remaining in the tank.
When the fuel level is low, FUEL RANGE LOW
displays.
The fuel economy data used to determine fuel
range is an average of recent driving conditions.
As your driving conditions change, this data is
gradually updated. Fuel range cannot be reset.
ECON (Economy):Press the information button
until ECON is displayed. Average fuel economy is
how many miles per gallon (mpg) or liters per
100 kilometers (L/100 km) your vehicle is getting
based on current and past driving conditions.
Press and hold the enter button while ECON is
displayed to reset the average fuel economy.
Average fuel economy will then be calculated
starting from that point. If the average fuel economy
is not reset, it will be continually updated each time
you drive.
210

Automatic Vehicle Unlocking: When Key is Off
or When Shift To Park
Exterior Perimeter Lighting During Remote
Keyless Entry Unlock
Select Language: (English, French, Spanish or
German)
When the desired option is reached, press the
enter button to toggle between the modes of that
option. To make a selection, press the MENU
button again.
If no selection is made within 10 seconds, the
display reverts back to the previous information
displayed.
The MENU mode is exited when the information
button is pressed, a 10 second time period
has elapsed, the ignition is turned to OFF, or the
end of the MENU list is reached.
SeeDIC Vehicle Personalization on page 216for
more information on the personalization options.
Enter
ENTER/r(Enter):Press this button to reset
certain functions and to turn off or acknowledge
messages on the DIC display. This button
also toggles through the options available in each
personalization menu.
DIC Warnings and Messages
These messages appear if there is a problem
detected in one of your vehicle’s systems.
A message will clear when that condition is no
longer present on the vehicle. To acknowledge a
message and clear it from the display, press
any of the three DIC buttons. If the condition is
still present, the warning message will come back
on the next time the vehicle is turned off and
back on. With most messages, a warning chime
sounds when the message displays. Your
vehicle may have other warning messages.
AUTO (Automatic) LIGHTS OFF:This message
displays if the automatic headlamp system is
disabled with the headlamp switch.
AUTO (Automatic) LIGHTS ON:This message
displays if the automatic headlamp system is
enabled with the headlamp switch.
212

Setting the Time for Radios with
Radio Data Systems (RDS)
To set the hour, press the clock button. The clock
symbol appears on the display and the hour
number ashes. Turn the ADJ (adjust) knob to
increase or to decrease the hours. To set
the minutes, press the clock button again. The
minute numbers ashes. Turn the ADJ knob
to increase or to decrease the minutes. The time
can be set with the ignition on or off.
To synchronize the time with an FM station
broadcasting Radio Data System (RDS)
information, press and hold the clock button to
enter the clock set mode, then press and hold the
clock button for three seconds until UPDATED
displays. If the time is not available from the
station, NO UPDATE displays.
RDS time is broadcast once a minute. After tuning
to an RDS broadcast station, it can take a few
minutes for the time to update.
Radio with CD
If your vehicle has the Monsoon audio system,
included are eight speakers and an eight channel
amplier. The radio displays MONSOON when
the radio or the ignition is turned on. See
your dealer for details.
United States shown, Canada similar
221

DISP (Display):Press this knob to switch the
display between the time and the temperature or
the radio station frequency and the temperature.
When the ignition is off, press this knob to display
the time.
For RDS, press this knob to change what appears
on the display while using RDS. The display
options are station name, RDS station frequency,
PTY, and the name of the program (if available).
For XM™ (if equipped), press this knob while
in XM mode to retrieve four different categories of
information related to the current song or
channel: Artist, Song Title, Category or PTY,
Channel Number/Channel Name.
To change the default on the display, press the
DISP knob until you see the desired display, then
hold the knob for two seconds. The radio
produces a beep and the selected display is now
the default.AUTOu(Automatic Volume):With automatic
volume, the audio system adjusts automatically
to make up for road and wind noise as you drive.
Set the volume at the desired level. Press this
button to select LOW, MEDIUM, or HIGH. AUTO
VOL LOW, AUTO VOL MEDIUM, or AUTO
VOL HIGH displays. Each higher setting allows for
more volume compensation at faster vehicle
speeds. As you drive, automatic volume increases
the volume, as necessary, to overcome noise at
any speed. The volume level should always sound
the same to you as you drive. AUTO VOL
NONE displays if the radio cannot determine the
vehicle speed or if the engine is not running.
To turn automatic volume off, press this button
until AUTO VOL OFF displays.
Finding a Station
BAND:Press this button to switch between FM1,
FM2, AM, or XM1 or XM2 (if equipped). The
display shows the selection.
ADJ (Adjust):Turn this knob to select radio
stations.
223

Setting the Tone
(Bass/Midrange/Treble)
TONE /P/Q(Bass/Treble):Press and release this
button until BASS, MID (midrange), or TREB
(treble) displays. Turn the ADJ (adjust) knob to
increase or to decrease the tone. The display
shows the bass, midrange, or treble level.
If a station is weak or has static, decrease the
treble.
To adjust bass, midrange, or treble to the middle
position, select BASS, MID, or TREB. Then
press and hold the tone button for more than
two seconds. One beep sounds and the
tone control adjusts to the middle position.
To adjust all tone controls to the middle position,
press and hold the tone button while no tone
control is displayed. ALL CENTERED displays and
a beep sounds. The bass, midrange, and treble
adjusts to the middle position.AUTO TONE/AUTO EQ (Automatic
Equalization):Press this button to select
customized equalization settings designed for
country, jazz, talk, pop, rock, and classical.
To return to the manual mode, press the AUTO
TONE or AUTO EQ button until CUSTOM
displays. You can also manually adjust the bass,
midrange, and treble using the tone button.
Adjusting the Speakers (Balance/Fade)
BAL/FADE /S(Balance/Fade):To adjust
the balance between the right and the left speakers,
push and release the balance and fade button until
BAL displays. Turn the ADJ (adjust) knob to move
the sound toward the right or the left speakers.
To adjust the fade between the front and the rear
speakers, push and release the balance and fade
button until FADE displays. Turn the ADJ knob to
move the sound toward the front or the rear
speakers.
To adjust balance or fade to the middle position,
select BAL or FADE. Then press and hold the
balance and fade button for more than
two seconds. One beep sounds and the speaker
control adjusts to the middle position.
225