speed RENAULT KANGOO 2013 X61 / 2.G Petrol V42 Injection Service Manual

17B-144
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF1072
PRESENT OR
STOREDAIR CONDITIONING COMPRESSOR RELAY CONTROLCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and the condition of the connector of the air conditioning compressor control relay,
component code 474 (for Logan, Sandero, Duster, Kangoo VLL) or the low speed fan assembly relay,
component code 784 (for Thalia 2/Symbol 2, Clio II F 6) and the connector of the injection computer, component
code 120.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
For Logan, Sandero, Duster:
–38K between components 474 and 120,
–3FB between components 1047 and 474,
For Clio II F 6:
–38K between components 784 and 120,
–3FB between components 983 and 784,
For Thalia 2/Symbol 2:
–38K between components 784 and 120,
–3FB between components 238 and 784,
For Kangoo VLL:
–38K between components 474 and 120,
–3FB between components 238 and
474.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Run command AC180 Air conditioning compressor relay control in order to check the correct operation of the
relay.
If the fault is still present, contact the Techline.
V42_V04_DF1072/V42_V05_DF1072/V42_V06_DF1072/V42_V14_DF1072/V42_V16_DF1072/V42_V18_DF1072

17B-145
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF1074
PRESENT OR
STOREDMOTORISED THROTTLE POSITION INCONSISTENT1.DEF: Inconsistency between throttle valve position and control.
2.DEF: Inconsistent signal.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is considered present under the following conditions:
–For 1.DEF engine running at idle speed.
Special note:
For 1.DEF, the OBD warning light illuminates,
For 2.DEF, the OBD warning light and level 2 fault warning light illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the motorised throttle valve connector, component code 1076 and the
injection computer connector, component code 120.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3AJB between components 1076 and 120,
–3AJC between components 1076 and 120,
–3MP between components 1076 and 120,
–3MQ between components 1076 and 120,
–3MO between components 1076 and 120.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
V42_V04_DF1074/V42_V05_DF1074/V42_V06_DF1074/V42_V14_DF1074/V42_V16_DF1074/V42_V18_DF1074

17B-162V2 MR-376-X76-17B050$100.mif
PETROL INJECTION
Fault finding – Status summary table17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TDC*: Top Dead Centre
GMV**: Fan assembly
s.v.***: solenoid valveTool status Diagnostic tool title
ET803Clutch switch start of travel
ET813Low speed fan assembly request by injection
ET814High speed fan assembly request by injection
ET819Low speed fan assembly final request
ET820High speed fan assembly final request
ET836TDC sensor signal
ET837Crankshaft synchronisation
ET842LPG switch
ET845Camshaft dephaser s.v.*** programming
ET846Injection protection
ET847LPG mode

17B-163
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$110.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ET001COMPUTER + AFTER IGNITION FEED
STATUS DEFINITIONPRESENT: This status indicates that the + after ignition feed is active.
"ABSENT": This status indicates that the + after ignition is not active.
"PRESENT"
NOTESNone.
With the ignition on and engine running warm at idle speed, + after ignition feed is activated.
In the event of a fault, apply the interpretation of DF047 Computer supply voltage.
V42_V04_ET001/V42_V05_ET001/V42_V06_ET001/V42_V14_ET001/V42_V16_ET001/V42_V18_ET001
PETROL INJECTION
Fault finding – Interpretation of statuses

17B-177V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET836TDC SENSOR SIGNAL
STATUS DEFINITIONDETECTED: This status indicates that the TDC sensor signal is detected.
NOT DETECTED: This status indicates that the TDC sensor signal is not detected.
Conformity check: Engine stopped, ignition on or engine running.
NOT DETECTEDIn the event of a fault, refer to the interpretation of fault DF120 Engine speed sensor
signal.
V42_V04_ET836/V42_V05_ET836/V42_V06_ET836/V42_V14_ET836/V42_V16_ET836/V42_V18_ET836

17B-180V2 MR-376-X76-17B050$120.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
OCR*: Opening cyclic ratioTool
ParameterDiagnostic tool title
PR002 Alternator charge
PR015Engine torque
PR030Accelerator pedal position
PR037Refrigerant pressure
PR041 Turbocharging pressure
PR055Engine speed
PR059 Inlet air temperature
PR064Coolant temperature
PR071 Computer feed voltage
PR084 Coolant temperature sensor voltage
PR089Vehicle speed
PR097Motorised throttle lower stop programmed value
PR098Upstream oxygen sensor voltage
PR099Downstream oxygen sensor voltage
PR102Canister bleed solenoid valve OCR*
PR118Measured throttle position gang 1
PR119Measured throttle position gang 2
PR138Richness correction
PR139 Operating adaptive richness
PR147Pedal potentiometer voltage gang 1
PR148Pedal potentiometer voltage gang 2
PR215 Sensor supply voltage no. 1
PR216 Sensor supply voltage no. 2
PR312Inlet manifold vacuum
PR313 Linearised manifold pressure
PETROL INJECTION
Fault finding – Parameter summary table

17B-181V2 MR-376-X76-17B050$120.mif
PETROL INJECTION
Fault finding – Parameter summary table17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
Tool
ParameterDiagnostic tool title
PR344 Pressure sensor voltage
PR427Average pinking signal
PR429Measured throttle position
PR444Integral idling speed regulation correction
PR446Upstream O2 sensor heating resistance
PR447Downstream O2 sensor heating resistor
PR448Ignition advance
PR469Cylinder 1 pinking value
PR471Cylinder 2 pinking value
PR473Cylinder 3 pinking value
PR475Cylinder 4 pinking value
PR492Motorised throttle position setpoint
PR538Measured throttle voltage, gang 2
PR539Measured throttle voltage gang 1
PR606Adaptive idling speed correction
PR624Richness regulation programming offset
PR625Richness regulation programming gain
PR743Alcohol level estimated in the tank
PR770Camshaft offset
PR814Number of active heating resistors
PR831Combustion misfiring counter

17B-186V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR055ENGINE SPEED
PA R A M E T E R
DEFINITIONThis parameter indicates the engine's rotational speed in rpm.
Conformity check with engine stopped and ignition on.
With the ignition on the value must be 0 rpm.
In the event of a fault, apply interpretation of DF120 Engine speed sensor signal.
Conformity check with the engine running and engine coolant temperature > 80°C
With the engine running at idle speed, the value must be  750 rpm.
In the event of a fault, apply the interpretation of DF120.
V42_V04_PR055/V42_V05_PR055/V42_V06_PR055/V42_V14_PR055/V42_V16_PR055/V42_V18_PR055

17B-187V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR059INLET AIR TEMPERATURE
PA R A M E T E R
DEFINITIONThis parameter indicates the air temperature in °C.
Conformity check with engine stopped and ignition on.
With the ignition on the inlet air temperature varies according to the exterior temperature.
In the event of a fault, consult the interpretation of fault DF002 Air temperature sensor circuit.
Parameter PR059  PR064 Coolant temperature engine cold.
Conformity check with the engine running and engine coolant temperature > 80°C
With the engine running at idle speed the inlet air temperature varies according to the engine coolant temperature.
In the event of a fault, refer to the interpretation of fault DF002.
V42_V04_PR059/V42_V05_PR059/V42_V06_PR059/V42_V14_PR059/V42_V16_PR059/V42_V18_PR059

17B-188V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR064COOLANT TEMPERATURE
PA R A M E T E R
DEFINITIONThis parameter indicates the engine coolant temperature in °C.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Conformity check with engine stopped and ignition on.
With the ignition on the coolant temperature varies according to the exterior temperature.
In the event of a fault, consult the interpretation of fault DF001 Coolant temperature sensor circuit.
Conformity check with the engine running and engine coolant temperature > 80°C
With the engine running at idle speed the coolant temperature varies according to the engine temperature.
If there is a fault, refer to the interpretation of fault DF001.
V42_V04_PR064/V42_V05_PR064/V42_V06_PR064/V42_V14_PR064/V42_V16_PR064/V42_V18_PR064