RENAULT MEGANE SCENIC 1995 Service Repair Manual

TOP OF BODY
Roof bow
PRE4503
45C
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the roof for a
roll-over.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Single part.
Bows (A) and (B) are mounted by rivets.
Bow (C) is spot welded.
PARTS CONCERNED (thickness in mm) :
1Roof bow 0.7
2Rear pillar upper reinforcement 1
3Roof bow support 1.2
45-8

TOP OF BODY
Roof bow
BOWS A and B
255c01-15315
45C
A = rivet diameter 4.8 mm
(joint with bow support)
255c02-15314
B
CAA11536-3R6
1
2
45-9

TOP OF BODY
Roof rear cross member
PRE4504
45D
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the roof for a
roll-over.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included. These are
dealt with in their respective section (refer to the
contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Single part.
PARTS CONCERNED (thickness in mm) :
1Roof rear cross member 0.7
2Rear quarter panel lining 0.7
3Rear corner reinforcement 1.2
45-10

TOP OF BODY
Roof rear cross member
255d01-15318
45D
A
CAT13318R2
13
B
CAA11538-1R2
C
TOD14617R4
1 3
1
2
3
45-11

SIDE OPENING ELEMENTS
Rear door panel
INTRODUCTION
The replacement of this part is a basic operation
for a side impact.
This part may be partially replaced (see cut and
method below).
NOTE : the original panels have MIG welded an-
chorage points. In repair, these points are not
made (sections A on the diagram below).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with:
- soundproofing,
- stiffener.
PRE4701
47A
PARTS CONCERNED (thickness in mm) :
1Door panel 0.7
2Door box section 0.7
3Door frame 0.8or
47-1

SIDE OPENING ELEMENTS
Rear door panel
47A
257a04-15322
A
TOB14587R5
12
257a06-15324
A
TOB14587R1
12
47-2

SIDE OPENING ELEMENTS
Rear door panel
47A
257a01-15320
or
B
➜
➝

TOB14587R1
12
➜➝
C
➜
➝
D
CAB11539R4
1
3
➜
TOB14587R1
12➝
47-3

SIDE OPENING ELEMENTS
Rear door panel
47A
E
CAS13033R3
1
1
47-4

SIDE OPENING ELEMENTS
Rear door panel
257a03-15321
47A
or
F
CAQ11697R6a
G
CAS13033R3
1
31
1
H
TOB14587R2
12
➜
➝➝➜
47-5

NON-SIDE OPENING ELEMENTS
Tailgate
REMOVAL
Remove the trim and disconnect the various wi-
ring harnesses (see sections 52 and 71).
Remove:
- the third stop light,
- the rear screen washer jet pipe,
- the wiring harness,
99386R1
48A
PRE4803
- the headlining plugs using a screwdriver (torx
20).
99621R2
Unclip the tailgate balancers at (A).
Remove the mounting nuts and remove the
hinges (B) (two persons required for this opera-
tion).
NOTE : if the tailgate or the roof is being repla-
ced, retain the height adjustment shims located
under the hinges (B).
To do this, use a cutting tool to destroy the finis-
hing seal around the shims and retain them.
The hinges are welded on the tailgate, so these
shims of thickness 1 mm are used to adjust the
clearance between the roof and the tailgate.
48-1