RENAULT MEGANE SCENIC 1995 Service Repair Manual

UPPER REAR STRUCTURE
Rear wing panel
INTRODUCTION
This part may be replaced in two ways:
• by part section as a basic operation for a rear
side impact (see diagram),
• completely, as a complementary operation to
the roof.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with:
- striker plate reinforcement,
- pin to be welded 3 x2.9,
- soundproofing,
- bumper mounting reinforcement assembly.
PRE4415
44A
or
PARTS CONCERNED (thickness in mm) :
1Wing panel 0.8
2Rear quarter panel lining 0.7
3Sill panel closure panel 1.5
4Rear pillar reinforcement 1
5Rear outer wheel arch 0.7
6Rear upper side drip moulding 1
7Lights moulding 0.7
8Rear end pillar lining 1
9Rear end panel 1
10Rear end pillar lower reinforcement 1
44-1

UPPER REAR STRUCTURE
Rear wing panel
254a03-15385
44A
A
CAS13033R4
B
CAE11546-6R5
C
CAQ11697R6a
D
CAE11546-8R1
1
1
12
421
1 42
E
CAE11546-2R1
15 2
44-2

UPPER REAR STRUCTURE
Rear wing panel
44A
F
CAB11539R6
G
CAQ11697R3
H
CAS13033R3
or 14
121
1
44-3

UPPER REAR STRUCTURE
Rear wing panel
254a01-15368
44A
I
CAN11691R7
J
CAS13033R4
or1
1
5 1
➜
➝➜
➝
44-4

UPPER REAR STRUCTURE
Rear wing panel
254a02-15382
44A
K
TOA14581R6
15
L
CAB11539R8
1 5
M
CAI11550R2
1
5
10
N
CAI11550R2
1
5
9
O
CAI11550R7
19 5
44-5

UPPER REAR STRUCTURE
Rear wing panel
254a05-15381
44A
P
CAB11540-1R7
1 6
Q
CAB11540-1R1
17
44-6

UPPER REAR STRUCTURE
Rear wing panel
COMPLETE REPLACEMENT
(with removal of the roof)
254a07-15384
44A
R
CAE11546-2R7
1 4 11
S
CAS13033R1
1
1
or
44-7

UPPER REAR STRUCTURE
Rear wing panel
254a06-15387
44A
T
CAB11540-1R3
1
6
254a04-15386
U
CAB11539R6
5 1
44-8

UPPER REAR STRUCTURE
Rear wing panel
44A
V
CAE11546-2R3
1
5
3
W
CAS13033R1
1
1
or
44-9

UPPER REAR STRUCTURE
Rear lights mounting
PRE4416
44B
INTRODUCTION
The replacement of this part is a complementary
operation to the wing panel.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Single part.
PARTS CONCERNED (thickness in mm) :
1Lights mounting 0.7
2Rear upper side drip moulding 1
3Rear end pillar lining 1
4Rear end panel 1
254b01-15380
A
CAA11536-2R7
12
44-10