RENAULT MEGANE SCENIC 1995 Service Repair Manual

UPPER REAR STRUCTURE
Rear end panel
PRE4422
44H
INTRODUCTION
The replacement of this part is a basic operation
for a rear impact.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with rear end panel lower reinfor-
cement.
PARTS CONCERNED (thickness in mm) :
1Rear end panel 1
2Body side lining 0.7
3Lights mounting 0.7
4Rear end pillar lower reinforcement 1
5Rear end cross member 0.8
6Rear end panel inner reinforcement 1
7Tailgate striker plate reinforcement 1.2
8Rear wing panel 1
254h01-15369
or
A
TOK14644-1R1
1
34
44-31

UPPER REAR STRUCTURE
Rear end panel
44H
B
CAA11536-2R8
1 3
C
CAB11539R7
D
CAE11546-2R8
1 4
1 4
5
E
CAB11539R7
1 5
F
CAE11546-2R8
1 4
6
44-32

UPPER REAR STRUCTURE
Rear end panel
254h02-15383
44H
G
J
CAE11546-8R4
51 7
H
CAT13326-1R6
1 45
I
CAQ11697R6
1
5
CAI11550R1
1
2
8
44-33

TOP OF BODY
Roof
INTRODUCTION
The replacement of this part is a basic operation
for a side impact or a roll-over.
COMPOSITION OF PART FROM PARTS
DEPARTMENT
PRE4501R
45A
PARTS CONCERNED (thickness in mm) :
1Roof 0.7
2Front roof cross member 0.7
3Windscreen pillar lining 1.5
4Body side 0.77
5Centre pillar reinforcement 1.5
6Rear corner reinforcement 1.2
7Rear roof cross member 0.7
8Rear upper side drip moulding 1
9Rear quarter panel lining 0.7
10Stretcher lining 1.2
11Centre pillar lining 1.2
12Rear end pillar lining 0.9
45-1

TOP OF BODY
Roof
255a01-15311
45A
A
CAQ11697R8
B
CAT13326-1R8
C
CAT13326-3R3
D
TOA14580-1R6
1
21
2
3
3 14
14
45-2

TOP OF BODY
Roof
255a02-15312
45A
E
CAP11696-2R2
F
TOP15254R2
G
CAP11696-2R2
H
CAA11536R5
14 3
1
4311
5318
1
45-3

TOP OF BODY
Roof
45A
I
J
CAN11689R1a
K
CAP11696-2R1
L
TOP15254R1
M
N
CAW13602R2
1612
1
7
1 461 96 4
CAP11696-2R1
1 49
CAP11696-2R1
1 45
45-4

TOP OF BODY
Roof
45A
O
P
CAJ11551-1R5 CAP11696-2R1
1
410
1 7 6
255a03-15312
15342R1
A = 70 mm
B = 500 mm
C = 500 mm
D = 300 mm
NOTE : apply a bead of adhesive mastic (C) in
zones (B) and (D) of the basic diagram, to rein-
force the roof where the roof bars are mounted.
E
Bead C
45-5

TOP OF BODY
Roof acoustic cross member
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the roof for a
roll-over.
For reasons of standardisation, the Parts
Department only supplies parts for the version wi-
thout sunroof.Where a sunroof is fitted originally,
the roof and the centre roof cross member must
be cut according to the diagram below.
These cuts must also be made to fit a sunroof as an
accessory.
IMPORTANT : the roof cross member has a struc-
tural reinforcement function. For the version with
sunroof, the sunroof frame fulfils this function.
When fitting a sunroof as an accessory it is re-
commended that only sunroofs approved by the
Renault accessories department are used.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Single part.
PRE4502
45B
PARTS CONCERNED (thickness in mm) :
1Acoustic cross member 0.7
2Centre pillar reinforcement 1.5For sunroof
45-6

TOP OF BODY
Roof acoustic cross member
LEFT HAND SIDE
255b01-15313
45B
RIGHT HAND SIDE
255b02-15316
A
CAA11536-3R6
B
CAA11536-5R6
1
2
1 2
45-7