air condition RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit Owners Manual

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 239
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 239V9 MR-372-J84-87B000$602.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET233
CHILDPROOF LOCK SWITCH
NOTESNo faults should be present or stored.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the condition and connection of the PE1 connector of the UCH (tabs broken, bent, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the child safety lock switch connector (bent, oxidised, broken tabs).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for an earth on connection MAM of component 135.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connection:
●Connection code 20AL between components 645 and 135.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation between connections 20AL and MAM of component 135 (Released position).
Check the continuity between connections 20AL and MAM of component 135 (Pressed position).
Replace the switch if necessary.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET233/UCH_V48_ET233/ UCH_V4C_ET233/
UCH_V4D_ET233 /UCH_V4F_ET233/UCH_V50_ET233

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table87B
87B - 246
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table87B
87B - 246V9 MR-372-J84-87B000$731.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table
*RCH: Passenger Compartment Heating Resistor
*CPE: Electric central door locking
*SR.: SunroofTool command Diagnostic tool title Vdiag
AC003Immobiliser warning light
V44, V48,
V4C, V4D,
V4F, V50 AC004Central door locking
AC005Central door unlocking
AC006Driver's door unlocking
AC007Rear screen wiper
AC008Front fog lights
AC009Rear fog lights
AC015Air conditioning button indicator light
AC016RCH* 1 relay
AC017RCH* 2 relay
AC018RCH* 3 relay
AC019Heated rear screen indicator light
AC020CPE* button indicator light
AC021Interior lights
AC022Left-hand direction indicator
AC023Right-hand direction indicator
AC024Card reader lighting
AC025One-touch window control/SR.* authorisation
AC026Start button lighting
AC027Footwell lights
AC030Headlight washer relay 1 (only if Vdiag 44 UPC)
AC031Headlight washer relay 2 (only if Vdiag 44 UPC)
AC032Driver's side external aerial testing
AC033Passenger's side external aerial testing
AC034Boot external aerial test
AC036Internal aerial test
AC037Transmitter aerial fault finding
AC076Child safety lock indicator light
MR-372-J84-87B000$731.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 248
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 248V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
AC003
IMMOBILISER INDICATOR LIGHT
NOTESNo faults should be present or stored.
The instrument panel must be detected as present on the multiplex network.
This command is for testing whether the immobiliser warning light is working.
The command lasts 10 seconds.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
The immobiliser indicator light does not come on when the command is performed.
Check the condition and connection of the instrument panel connector.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
With the command running, check for earth on connection 88T of component 427.
If okay, replace the instrument panel.
Check the condition and connection of connector PE2 on the UCH
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 20W between components 645 and 427.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
MR-372-J84-87B000$774.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 249
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 249V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC004
LOCK DOORS AND BOOT
NOTESNo faults should be present or stored.
This command is for testing locking relay operation.
Note:
The driver's door circuit is shared with the fuel tank flap circuit.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
One or more doors do not lock when the command is activated.
Check the condition and connection of the PP2 connector on the UCH.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the connector on the faulty lock(s).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on the following connections:
●Connection code MAM.
●Connection code 87H of component 140.
●Connection code MZ.
●Connection code 87A of component 139.
●Connection code MAN.
●Connection code 87G of component 141.
●Connection code MAQ.
●Connection code 87B of component 138.
●Connection code 20BC.
●Connection code 20BH of component 844.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If faulty: If OK:
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 251
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 251V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC005
AC006
UNLOCK DOORS AND BOOT
DRIVER'S DOOR UNLOCKING
NOTESNo faults should be present or stored.
This command is for testing unlocking relay operation.
The driver's door circuit is shared with the fuel tank flap circuit.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
One or more doors do not unlock when the commands are activated.
Check the condition and connection of the PP2 connector on the UCH.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the connector on the faulty lock(s).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on:
●Connection code MAM.
●Connection code 87H.
Of component 140.
●Connection code MZ.
●Connection code 87A.
Of component 139.
●Connection code MAN.
●Connection code 87G.
Of component 141.
●Connection code MAQ.
●Connection code 87B.
Of component 138.
●Connection code 20BC.
●Connection code 20BH.
Of component 140.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If faulty: If OK:
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 253
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 253V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC007
REAR SCREEN WIPER
NOTESNo faults should be present or stored.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
The rear screen wiper does not operate when the command is activated.
Check the condition and connection of the rear screen wiper motor connector.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on connection MZ of component 211.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
With the command running, check for + 12 V feed on connection 36A of component 211.
If everything is correct, replace the rear screen wiper motor.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of connector PE3 on the UCH.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connections:
●Connection code 36A.
●Connection code 36C between components 645 and 211.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 254
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 254V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC008
FRONT FOG LIGHTS
NOTESCheck:
–the condition and connection of the front fog lights fuse,
–the condition of the bulbs.
Replace the bulbs if necessary.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
The rear screen wiper does not operate when the command is activated.
Check the condition and connection of connector PPA on the UPC (Vdiag 44) or connector AN on the UPC
(Vdiag 48 or above).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the bulb connectors.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on R9 connection then check the connections of the bulb connectors.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for + 12 V on the fog light connectors they are being controlled by command AC004.
If the + 12 V on the connectors is correct, replace the bulb(s).
Check the insulation and continuity of the following connections:
●Connection code 8F between components 176 and 1337.
●Connection code 8E between components 177 and 1337.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 255
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 255V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC009
REAR FOG LIGHTS
NOTESNo faults should be present or stored.
This command is for testing operation of the rear fog lights.
Check the bulbs.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Left-hand drive
Check the condition and connection of the connector for each rear light.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on connection MZ on component 173.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
With the command running, check for + 12 V feed on connection 9P of component 173.
If the + 12 V feed is correct, check the bulbs again and if the bulbs still do not work, replace the rear light.
Check the condition and connection of UCH connector PP3.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 9P between components 645 and 173.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 256
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 256V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC009
CONTINUED
Right-hand drive
Check the condition and connection of the connector for each rear light.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on connection MAQ on component 172.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
With the command running, check for + 12 V feed on connection 9P of component 172.
If the + 12 V feed is correct, check the bulbs again and if the bulbs still do not work, replace the rear light.
Check the condition and connection of UCH connector PP3.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 9P between components 645 and 172.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 257
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 257V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC015
AIR-CONDITIONING BUTTON INDICATOR LIGHT
Manual air conditioning only
NOTESNo faults should be present or stored.
This command is for testing operation of the air-conditioning indicator light.
Apply the after ignition feed, and the air conditioning control panel should light up.
The command lasts 7 seconds.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
The indicator light does not light up when the command is activated.
Check the condition and connection of the heater control panel connector.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on connection NAM of component 316.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
With the command running, check for + 12 V feed on connection 38ES of component 316.
If OK, replace the control panel.
Check the condition and connection of connector PE2 on the UCH
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 38ES between components 645 and 319.
●Connection code NAM between component 319 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.