sensor RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit User Guide

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-40
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-40V9 MR-372-J84-87B000$129.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
3.3 Special features of the rain sensor (if fitted to the vehicle)
The rain and light sensor is a single sensor, connected to the UCH by a single connection. This sensor is installed on
the windscreen.
The rain sensor enables the windscreen wipers to be operated automatically and controls the wiper speeds according
to the quantity of water on the windscreen.
The sensor is activated by setting the wiper stalk to AUTO position.
Depending on the vehicle's bodywork, two cases are possible for the operation of the rain sensor:
a) Phase 1 bodywork:
Automatic operation of the rain sensor is inhibited following ignition switch-off with the wiper stalk in the Auto position.
To reactivate operation when next switching on the ignition, set the wiper control stalk in the neutral position then
return it to the Auto position.
b) Phase 2 bodywork:
Automatic operation of the rain sensor remains active following ignition switch-off with the wiper stalk in the Auto
position.
For a vehicle which is fitted with a rain sensor, with automatic detection activated, the rear screen wiper starts to
operate if reverse gear is engaged and if the sensor has detected rain for more than 1 minute.
The wiper intermittent speed ring is used to modify the sensor's sensitivity to rain and therefore the time
between wipes.
When the vehicle is not fitted with a rain sensor, the intermittent speed position on the control stalk takes the place of
the Auto position.
The status ET118 Rain sensor sensitivity ring position can be interpreted if the vehicle is configured with rain
sensor and inhibits status ET096 Intermittent wipe ring position.
The operation of the rain sensor can be displayed using status ET114 Wiper request by rain sensor, and by
configuration reading LC044 Rain/light sensor.
Configuration CF035 Rain/light sensor is available during UCH configuration (SC008 UCH type) (see
Configurations and programming). Information displays Rain and light sensor Multiplex network
Steering
column
control UCH Protection and Switching Unit
Side lights Windscreen wiper
Dipped headlights
Main beam headlights

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-43
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-43V9 MR-372-J84-87B000$129.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
4FUNCTION: LIGHTING
4.1 Sub-function: LIGHTING CONTROL
The UCH receives the request from the driver, from the lighting stalk, from the hazard warning lights button and, if
fitted to the vehicle, from the light detector.
The UCH requests the Protection and Switching Unit, via the multiplex network, to provide power to the side lights,
dipped headlights, main beam headlights and fog lights (front).
If a request to activate the lighting is made, the UPC provides power to the xenon bulb computers.
The dipped headlights are still supplied when the main beam headlights are activated.
The following statuses can be displayed:
ET081 Lighting stalk position.
ET082 Rear fog lights request.
ET085 Hazard warning lights switch.
ET083 Left-hand direction indicator request.
ET084 Right-hand indicator request.
If the UCH cannot determine the position of the control stalk, or inform the Protection and Switching Unit of the
control stalk's position, the Protection and Switching Unit will activate the dipped headlights.
4.2 Sub-function: LIGHTING POWER
The UCH controls the power supply for the rear fog light (a single one), direction indicators and interior lighting (roof
lights and footwell/floor lights).
The interior lighting request can be displayed using the ET112 Interior lighting control status.
Operation of the lights powered by the UCH can be checked using the actuator commands AC009 Rear fog lights,
AC022 Left-hand direction indicator, AC023 Right-hand direction indicator, AC021 Interior lights and AC027
Footwell/floor lighting.
Information displays Rain and light sensor Multiplex network
Steering column
controlUCHProtection and Switching
Unit
Rear fog light
Direction indicators
Interior lighting
Side lightsMain beam
headlights
Dipped
headlightsFront fog lights

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-45
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-45V9 MR-372-J84-87B000$129.mif
4.4 Special features of the light sensor (if fitted to the vehicle).
Information displays Rain and light sensor Multiplex network
Steering column
controlUCHProtection and Switching
Unit
The rain and light sensor is a single sensor, connected to the UCH by a single connection. This sensor is installed on
the windscreen.
The light sensor enables the side lights and dipped headlights to be operated automatically as soon as the vehicle is
in a dark place (tunnel, night, gloomy weather conditions, etc.).
The status of the light sensor can be displayed using ET115 Lights on request by light sensor, and by configuration
reading LC044 Rain/light sensor.
Configuration CF035 Rain/light sensor is available during UCH configuration SC008 UCH type (see
Configurations and programming).
To activate the automatic lighting function, press the AUTO button on the lighting stalk for at least 4 seconds. This
action is confirmed by two beeps.
To deactivate the automatic lighting function, switch the engine off and press the AUTO button on the lighting stalk
for at least 4 seconds. A beep confirms this action and the message Automatic lighting OFF appears on the
instrument panel.
Any other operation on the lighting stalk overrides and cancels automatic operation.
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
Side lightsWindscreen
wiper
Dipped
headlights
Main beam
headlights

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-46
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-46V9 MR-372-J84-87B000$129.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
5. TYRE FUNCTION
SYSTEM COMPOSITION
The tyre pressure monitor system consists of the following components:
–four sensors (one on each wheel but not on the spare wheel),
–a computer (UCH),
–an instrument panel display for the driver.
WARNING:
It is forbidden to install PAX System tyres on a vehicle without PAX System tyres as standard.
In the MEGANE II family, PAX System tyres can only be installed on the 5-seat SCENIC II.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-47
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-47V9 MR-372-J84-87B000$129.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
SYSTEM OPERATION
–The valves are activated approximately 1 minute after the vehicle has been running at a speed above 12 mph
(20 km/h).
–During driving, the valves emit signals every minute.
–The valves remain active for 15 minutes after the vehicle stops, then switch to standby mode.
–In standby mode, the valves emit signals only if they detect a pressure difference between two successive
measurements exceeding 68 mbar or if the pressure difference since last emitting exceeds 68 mbar (due to tyre
cooling).
–The tyres are considered to be cold when the vehicle speed has been zero for 1h 45 min.
–The minimum time for detection of a leak is approximately 15 minutes.
–The message Inflate tyres for motorway is displayed only if the vehicle travels at more than 102 mph (170 km/
h) (as an indication) for 3 minutes and the pressure on at least one of the tyres is 400 mbar less than the
recommended pressure at low speed. This message is inactive if the tyres are inflated to motorway pressure,
irrespective of the vehicle speed.
–Alert thresholds:
–over-inflation when cold = recommended pressure + 700 mbar,
–over-inflation when hot = recommended pressure + 850 mbar,
–under-inflation = recommended pressure - 400 mbar,
–serious under-inflation = recommended pressure - 600 mbar,
–imbalance = difference in pressure between the left-hand and right-hand wheels on the same axle greater
than 500 mbar.
–Information messages for the driver:
–Stop! Tyre puncture + STOP warning light + wheel concerned is highlighted on instrument panel display +
buzzer.
–Adjust tyre pressure + the wheel concerned is highlighted on instrument panel display.
–Inflate tyres for motorway + four wheels highlighted on instrument panel display.
–Tyre sensor fault + the wheel concerned is erased.
–Electronic fault + "Service" warning light + the four wheels concerned disappear from the instrument panel
display.
–No display of the tyre inflation pressure on the instrument panel on MEGANE II.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-48
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-48V9 MR-372-J84-87B000$129.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
MATCHING THE VALVE TO THE TYRE
Whenever wheels are swapped over, reprogram the new valve positions in the UCH using the diagnostic tool.
The coloured rings will then have to be placed back in the location marked on the label on the driver's door.
Ring colours:
–Front left-hand: green.
–Front right-hand: yellow.
–Rear left-hand: red.
–Rear right-hand: black.
WINTER AND SUMMER TYRES
On leaving the factory, it is the summer wheel set that is configured in the UCH, but customers can fit their vehicle
with a winter set (winter wheels = wheel rims + sensors + special tyres).
The first time a set of winter wheels is fitted, program the codes of the four valves. Thereafter, whenever the set of
tyres is changed, recognition is automatic without having to touch the UCH.
Establishing communication between the UCH and the CLIP diagnostic tool:
–Connect the wire to the diagnostic socket and switch on the ignition.
–Switch on the diagnostic tool.
–Select the vehicle type and carry out the multiplex network test.
–Select the Tyre function.
–Follow the fault finding procedure described previously.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-57
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-57V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
5/ TYRE PRESSURE MONITORING SYSTEM FUNCTION
5.1 PROGRAMMING PROCEDURE FOR THE 4 VALVE CODES (SC002)
SC002:
Programming the four valve codes
IMPORTANT:
Any operation involving the replacement of a wheel sensor, requires perfect knowledge of the
recommendations defined in Repair Manual 364 (for Mégane II) or 370 (for Scénic II), section 35.
●Inflate the four tyres to 3.8 bar.
●Establish communication with the UCH using the diagnostic tool.
●Select the Repair mode menu.
●Select the Programming menu.
●Select line SC002 in the Tyre function.
●The stored codes and valve sets detected are displayed.
●Select the Valve set selection menu, then Summer or Winter.
●Confirm to display the Valve programming conditions table.
●Confirm by selecting next to obtain the Find valve codes menu.
●Excite each valve by holding the valve exciter against the tyre just below the valve in question.
●Start with the front left-hand wheel.
●Wait for the new code to appear on the screen before moving on to the next valve.
●The order for programming the codes is as follows:
Front left-hand Front right-hand Rear right-hand Rear left-hand
●Click on the "Confirm" button to transmit the codes to the UCH.
●Inflate the tyres to the recommended pressures.
●Carry out a road test: speed > 12 mph (20 km/h) for 10 minutes.
●Check that no message appears on the instrument panel.
IMPORTANT:
When swapping wheels over, reprogram the UCH with the new valve positions using the diagnostic tool and
program the valve codes.
The coloured rings will then have to be placed back in the location marked on the label on the driver's door.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-62
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-62V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
8/ UCH TYPE CONFIGURATION PROCEDURE (SC008)
8.1 Vdiag 44, 48
This procedure will enable the UCH to be configured in relation to the vehicle to provide optimum running.
–Click on the Repair mode and in the Programming menu,
–confirm line SC008 UCH type,
–follow the procedure and enter the following data:
–CF097 Vehicle type (3-door/4-door/5-door/cabriolet/extended MPV/MPV/Estate),
–confirm, follow the procedure and enter the following data:
–CF010 Hands-free function (WITH or WITHOUT),
–CF023 Tyre pressure monitoring system function (WITH or WITHOUT),
–CF057 Type of heating resistors (NONE, 1000 W, or 1800 W),
–CF019 Type of air conditioning (HEATING, AUTOMATIC, MANUAL),
–CF027 Type of windscreen (TINTED, HEAT INSULATING),
–CF035 Rain/light sensor (WITH or WITHOUT),
–CF014 Daytime running lights (WITH or WITHOUT),
–CF022 Factory fitted perimeter protection (WITH or WITHOUT): function only available on vehicles for the
Mexican market,
–CF173 One-touch window(s)/Sunroof (WITH or WITHOUT),
–confirm, follow the procedure and enter the following data:
–CF036 Selective opening of the opening elements (WITH or WITHOUT) Only if CF010 = WITHOUT
–confirm, follow the procedure and enter the following data:
–CF085 Valet card function (WITH or WITHOUT) Function only available in Mexico,
–(This status will only be available if the following conditions are met: CF036 Selective opening of opening
elements = WITH),
–check that the options configured are those desired and finish.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-63
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-63V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
8.2 Vdiag 4C and 4D:
This procedure will enable the UCH to be configured in relation to the vehicle to provide optimum running.
–Click on the Repair mode and in the Programming menu,
–confirm line SC008 UCH type,
–follow the procedure and enter the following data:
CF097 Vehicle type (3-door/4-door/5-door/cabriolet/extended MPV/MPV/Estate).
CF011 Gearbox type (BVA or BVM).
CF020 Type of driving style (Right-hand or Left-hand).
CF028 Engine type (F or K)
–confirm, follow the procedure and enter the following data:
CF010 Hands-free function (WITH or WITHOUT),
CF023 Tyre pressure monitoring system (WITH or WITHOUT),
CF057 Type of heating resistors (NONE, 1000 W, or 1800 W),
CF019 Type of air conditioning (HEATING, AUTOMATIC, MANUAL),
CF027 Type of windscreen (TINTED, HEAT INSULATING),
CF087 Front fog light (WITH or WITHOUT),
CF014 Daytime running lights (WITH or WITHOUT),
CF012 Rain sensor (WITH or WITHOUT),
CF029 External temperature sensor (WITH or WITHOUT).
–confirm, follow the procedure and enter the following data:
CF036 Selective opening of opening elements (WITH or WITHOUT): Only if CF010 = WITHOUT.
CF016 PAX system type tyre (WITH or WITHOUT): Only if CF097 = MPV or extended MPV or cabriolet and if
CF023 = WITH.
CF100 Deadlocking (WITH or WITHOUT).
CF013 Light sensor (WITH or WITHOUT): Only if CF014 = WITHOUT.
CF022 Factory fitted
perimeter protection (WITH or WITHOUT). Function only available on vehicles sold in
Mexico. CF083 One touch window(s) (WITH or WITHOUT): Absent if CF097 = Cabriolet.
–confirm, follow the procedure and enter the following data:
CF085 Valet card function (WITH or WITHOUT) Function only available in Mexico. Only if CF036 = WITH and
CF023 = WITHOUT.
–check that the options configured are those desired and finish.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-64
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-64V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
8.3 Vdiag 4F and 50:
This procedure will enable the UCH to be configured in relation to the vehicle to provide optimum running.
–Click on the Repair mode and in the Programming menu,
–confirm line SC008 UCH type,
–follow the procedure and enter the following data:
–CF097 Vehicle type (3-door/4-door/5-door/cabriolet/Estate) except for Scénic (extended MPV/MPV).
–confirm, follow the procedure and enter the following data:
CF010 Hands-free function (WITH or WITHOUT),
CF023 Tyre pressure monitoring system (WITH or WITHOUT),
CF057 Type of heating resistors (NONE, 1000 W, or 1800 W),
CF019 Type of air conditioning (HEATING, AUTOMATIC, MANUAL),
CF027 Type of windscreen (TINTED, HEAT INSULATING),
CF035 Rain/light sensor (WITH or WITHOUT),
CF014 Daytime running lights (WITH or WITHOUT),
CF189 Protection type (TYPE 1, TYPE 2 or WITHOUT): TYPE 1 = with factory
fitted perimeter protection, TYPE
2 = with Cobra type alarm and WITHOUT = without factory fitted perimeter protection and without Cobra alarm.
–confirm, follow the procedure and enter the following data:
CF173 One-touch window(s)/sunroof (1 OTW* phase 1/1 OTW* phase 2/2 or 4 OTW*/WITHOUT): Absent if
CF097 = Cabriolet.
1 OTW* phase 1 = 1 driver side one touch window with a phase 1 bodywork vehicle.
1 OTW* phase 2 = 1 driver side one touch window with a phase 2 bodywork vehicle.
2 or 4 OTW = 2 or 4 one touch windows.
WITHOUT = no one touch windows on the vehicle.
–confirm, follow the procedure and enter the following data:
CF188 Production number type (Jxxxxxx or OTHER): only if CF097 = 4-doors and CF173 = 1 OTW* Phase 1.
The production number is located on the oval plate on the vehicle's right-hand side B-pillar. The production number
consists of 7 characters: 1 letter indicating the production plant followed by 6 figures.
–If the production number starts with the letter J, select Jxxxxxx.
–If the production number does not start with the letter J, select Other.
–Confirm, follow the procedure and enter the following data:
CF036 Selective opening of opening elements (WITH or WITHOUT): Only if CF010 = WITHOUT CF016 PAX
System type tyre (WITH or WITHOUT): Only if CF097 = MPV or Extended MPV and if CF023 = WITH.
–confirm, follow the procedure and enter the following data:
CF085 Valet card function (WITH or WITHOUT): Only if CF036 = WITH and CF023 = WITHOUT.
–check that the options configured are those desired and finish.
OTW*: One-touch window(s)IMPORTANT
Only configure WITH valet card function when the vehicle is electrically pre-equipped with the valet option.
Incorrect configuration may cause certain pieces of equipment to malfunction.
Note:
After having finished the UCH configuration, run command AC037 "TRANSMITTING AERIALS FAULT FINDING"
and check that there are no faults.