sensor RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit Service Manual

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -132
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -132V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre approval (continued 2)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre approval ET035:Rear left-hand
wheel valve signalOK
ABSENT
OVER-INFLATED
FLAT
UNDER-INFLATEDCheck that the tyre pressure is
at the recommended pressure
(see MR 364 (Mégane II) or
MR 370 (Scénic II),
Mechanical, 35A, Tyre
pressure: Identification).
If status ET035 is not OK,
consult the fault finding
procedure for status ET035.
PR006:Rear left-hand
wheel pressure0 bar < X < 3.55 barIf X = 0 bar, consult the fault
finding procedure for parameter
PR006.
Check that the recommended
pressure (PR009 to PR012)
corresponds correctly to the
vehicle.
PR022:Rear left-hand tyre
temperature- 40ºC normal that the temperature is
50˚C and the pressure is 0 bar.
Perform a road test so that the
sensor emits the actual
temperature and pressure.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -135
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -135V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
LIGHTING FUNCTION
Sub-function: Lighting command
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
Lighting
controlET081:Lighting switch
positionOFF
SIDE
DIPPED
MAIN BEAM HEADLIGHTS
HAZARD LIGHTS In the event of a fault,
refer to the
interpretation of status
ET081.
ET115:Request to switch
on lights by light
sensor PRESENT
ABSENTIn the event of a fault,
consult the
interpretation of status
ET115.
ET169:EngineSTOPPEDIn the event of a fault,
refer to the
interpretation of
status ET169.
ET113:Automatic lighting
button DEPRESSED
RELEASED In the event of a fault,
consult the
interpretation of
status ET113.
ET111:Front fog lights
requestPRESENT
ABSENT In the event of a fault,
consult the
interpretation of
status ET111.
ET082:Rear fog lights
requestPRESENT
ABSENT In the event of a fault,
consult the
interpretation of
status ET082.
ET085:Hazard warning
lights buttonDEPRESSED
RELEASED In the event of a fault,
refer to the
interpretation of
status ET085.
ET083:Left-hand indicator
requestPRESENT
ABSENT In the event of a fault,
refer to the
interpretation of
status ET083.
ET084:Right-hand indicator
requestPRESENT
ABSENT In the event of a fault,
refer to the
interpretation of
status ET084.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -136
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -136V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
WIPING FUNCTION
Sub function: Wiper control
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
Wiper controlET077:Wiper stalk positionOFF
INTERMITTENT
LOW SPEED HIGH SPEEDIn the event of a fault,
refer to the
interpretation of status
ET077.
ET096:Wiper stalk
intermittent speed
ring position1
2
3
4In the event of a fault,
consult the
interpretation of
status ET096.
ET118:Rain sensor
sensitivity ring
position
ET114:Wiper request by rain
sensorPRESENT
ABSENTIn the event of a fault,
consult the
interpretation of
status ET114.
ET078:Windscreen washer
requestPRESENT
ABSENTIn the event of a fault,
refer to the
interpretation of status
ET078.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -140
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -140V9 MR-372-J84-87B000$430.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RAID: Renault Anti-Intruder Device
*CPE: Electric central door locking
*Lckg: Locking Tool status Diagnostic tool title Vdiag
ET041Opening rear screenV48, V4C, V4D,
V4F, V50
ET042Passenger door V44, V48, V4C,
V4D, V4F, V50
ET043RAID* function authorisation by CPE*
V44, V48, V4C,
V4D, V4F, V50 ET044CPE* button
ET045RF signal received
ET046Engine immobiliser
ET047Brake pedal position
ET048Clutch pedal position
ET050Tailgate/Boot
ET051Rear left-hand door
ET052Rear right-hand door
ET053Driver's door
ET054Optical sensors supplied
ET055Front driver side optical sensor
ET056Rear driver side optical sensor
ET057Passenger side front/rear optical sensor
ET058Lckg* button on driver's side handles
ET059Lckg* buttons on passenger's side handles
ET060Tailgate locking button
ET061Open tailgate request
ET062Open rear screen requestV48, V4C, V4D,
V4F, V50

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -141
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -141V9 MR-372-J84-87B000$430.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*Trip computer: Not authorised
*Sunroof: Tool status Diagnostic tool title Vdiag
ET066Card detected button
V44, V48, V4C,
V4D, V4F, V50 ET067Card button press recognised
ET068Most recently locked by
ET069Most recently unlocked by
ET070Start button
ET071 Unprogrammed steering lock
ET072Steering lock
ET073Steering lock sensor signal
ET075+ Accessories present
ET077Wiper stalk position
ET078Windscreen washer request
ET079Rear screen washer request
ET080Rear screen wiper request
ET081Lighting switch position
ET082Rear fog lights request
ET083Left-hand indicator request
ET084Right-hand indicator request
ET085Hazard warning lights button
ET086Electric child safety lock V44, V48, V4C
ET087Sunroof*/one touch electric window authorisation
V44, V48, V4C,
V4D, V4F, V50 ET088Deadlocking activation source
ET090Deadlocking deactivation source
ET096Wiper stalk intermittent speed ring position
ET097Rear screen wiper park position
ET098ADAC* button
ET108Automatic gearbox lever position
ET109Reverse gear engaged
ET110UCH request to injection or Protection and Switching Unit
ET111Front fog lights request
ET112Interior lighting control

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -142
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -142V9 MR-372-J84-87B000$430.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
Tool status Diagnostic tool title Vdiag
ET113Automatic lighting button
V44, V48, V4C,
V4D, V4F, V50 ET114Wiping request via rain sensor
ET115Request to switch on lights by light sensor
ET118Rain sensor sensitivity ring position
ET119UCH request to steering column lock
ET159Rear left-hand door child safety lock
V4D, V4F, V50
ET160Rear right-hand door child safety lock
ET169Engine V44, V48, V4C,
V4D, V4F, V50
ET194Passenger's door or bonnet V4C, V4D, V4F,
V50
ET195UCH frequency (in MHz)
V44, V48, V4C,
V4D, V4F, V50
ET205Type of UCH radio frequency aerial
ET229Injection immobiliser code V4F, V50
ET230Child safety lock V4D, V4F, V50
ET233Child safety lock switchV44, V48, V4C,
V4D, V4F, V50
ET248Steering column lock immobiliser code
V4F, V50
ET250Injection

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -158
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -158V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET032
ET033
ET034
ET035FRONT LEFT-HAND WHEEL VALVE SIGNAL
FRONT RIGHT-HAND WHEEL VALVE SIGNAL
REAR RIGHT-HAND WHEEL VALVE SIGNAL
REAR LEFT-HAND WHEEL VALVE SIGNAL
NOTESBefore carrying out any operation, apply the fault finding procedure (see Introduction).
Special note:
If a wheel is equipped with a tyre pressure sensor, precautions must be taken
when removing/refitting tyres.
Failure to take the precautions specified in Section 35 of Workshop Repair
Manual 364 (for Mégane II) or 370 (for Scénic II) could result in the sensor being
damaged, and potential operating faults in the tyre pressure monitoring system.
CORRECT:The sensor is operating correctly and the pressure is correct.
Absent:The UCH is not receiving the signal from the sensor.
Over-inflated:The sensor sends a "tyre over-inflated" signal.
Puncture:The sensor sends a "tyre severely under-inflated" signal (pressure - 0.6 bar) or a rapid pressure
loss signal.
Under-inflated:The sensor sends a "tyre under-inflated" signal.
STEP 1
Start by checking the tyre inflation and if necessary restore to the recommended pressure.
Next, to ensure that the wheel sensors are functioning properly, at each conformity check, make sure all sensors
really are transmitting. To do this, create a tyre leak and check that its status changes:
Initial status = over-inflated deflate Final status = Correct or puncture or under-inflated
Initial status = puncture or under-inflated inflate Final status = Correct or over-inflated
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
UCH_V44_ET032/UCH_V48_ET032/UCH_V4C_ET032/UCH_V4D_ET032/UCH_V4F_ET032/UCH_V50_ET032/UCH_V44_ET033/
UCH_V48_ET033/UCH_V4C_ET033/UCH_V4D_ET033/UCH_V4F_ET033/UCH_V50_ET033/UCH_V44_ET034/UCH_V48_ET034/
UCH_V4C_ET034/UCH_V4D_ET034/UCH_V4F_ET034/UCH_V50_ET034/UCH_V44_ET035/UCH_V48_ET035/UCH_V4C_ET035/
UCH_V4D_ET035/UCH_V4F_ET035/UCH_V50_ET035

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -159
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -159V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET032
ET033
ET034
ET035
CONTINUED
STEP 2
IMPORTANT:
Wait 1 minute and 30 seconds before checking the change of status.
–If the original status is: over-inflated or under-inflated
Consult ALP 52 "Adjust tyre pressure" message appears (the wheel concerned is highlighted on the
display) and ALP 56 "Adjust tyre pressure" message appears (2 wheels are highlighted on the display).
–If the original status is: puncture
Consult ALP 56 "Stop! Tyre puncture" message appears (the wheel is highlighted on the display).
–If the original status is: absent
Consult ALP 54 "Tyre sensor fault" message appears (wheel warning light disappears) and ALP 55 "Tyre
sensor fault" message appears (4 wheel warning lights disappear).
If the status does not change, replace the sensor on the wheel concerned by following the instructions and the
programming procedure for the four valve codes, SC002 Program 4 valve codes (see Configurations and
programming).
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 176V9 MR-372-J84-87B000$516.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
ET054
OPTICAL SENSORS SUPPLIED
NOTESAfter 72 hours without an attempt to open the vehicle, the UCH cuts out the
optical sensors' power supply.
To restore the power supply to the optical sensors, pull the handle to wake-up
the UCH.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
The vehicle has been immobilised for fewer than 72 hours:
Check that the UCH is in hands-free configuration by means of LC001 Hands-free function configuration reading.
If everything is correct, contact the Techline.
The vehicle is immobilised after more than 72 hours:
Check the insulation against 12 V feed of the following connection (door handle pulled):
●Connection code 26Q between components 645 and 1083.
Check the insulation against 12 V feed of the following connection (door handle pulled):
●Connection code 26Q between components 645 and 1085.
Check the earth on connection 26Q of the PE3 connector of the UCH by pulling a handle.
Is there an earth?
YES
NO
Contact the Techline.
Check the continuity on the following connection:
●Connection code 26Q.
Between components 645 and 1083.
Between components 645 and 1085.
If the connection or connections are faulty and there is a repair procedure
(see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Check the earth of component 1083 on connection MAN.
Check the earth of component 1085 on connection MAQ.
If the connector is faulty and if there is a repair procedure (see Technical Note
6015A, Repairing electrical wiring, Wiring: Precautions for repair), repair the
connector; otherwise, replace the wiring.
Check the continuity between connections 26Q and MAN (with the handle pulled)
of component 1083; if there is insulation, replace the handle.
Check the continuity between connections 26Q and MAQ (with the handle pulled)
of component 1085; if there is insulation, replace the handle.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET054/UCH_V48_ET054/ UCH_V4C_ET054/
UCH_V4D_ET054 /UCH_V4F_ET054/UCH_V50_ET054
MR-372-J84-87B000$516.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 177V9 MR-372-J84-87B000$516.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET055
ET056
ET057
DRIVER'S SIDE FRONT OPTICAL SENSOR
DRIVER'S SIDE REAR OPTICAL SENSOR
PASSENGER SIDE FRONT/REAR OPTICAL SENSORS
NOTESNo faults should be present or stored.
Switch the ignition on, then switch it off.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check that the status ET054 Optical sensor supplied is YES.
Place your hand behind the door handle; make sure the corresponding status is active.
If the status is inactive, lock the vehicle and pull the handle.
Is the status ACTIVE?
YES
NO
Check the condition of the reflective surface inside the handle (frost, dirt).
Check the condition of the optical sensor.
If necessary, replace the sensor.
Check the insulation and continuity of the following connections:
●Connection code 26P.
Between components 645 and 1083.
Between components 645 and 1084.
Between components 645 and 1085.
Between components 645 and 1086.
●Connection code 26T between components 645 and 1084.
●Connection code 26S between components 645 and 1086.
●Connection code 26Q.
Between components 645 and 1083.
Between components 645 and 1085.
●Connection code MAN between component 1083 and earth.
●Connection code MAM between component 1084 and earth.
●Connection code MAQ between component 1085 and earth.
●Connection code MZ between component 1086 and earth.
If the connection or connections are faulty and there is a repair procedure
(see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET055/UCH_V48_ET055/ UCH_V4C_ET055/UCH_V4D_ET055/ UCH_V4F_ET055/UCH_V50_ET055/
UCH_V44_ET056/UCH_V48_ET056/ UCH_V4C_ET056/UCH_V4D_ET056/ UCH_V4F_ET056/UCH_V50_ET056/
UCH_V44_ET057/UCH_V48_ET057/ UCH_V4C_ET057/UCH_V4D_ET057/ UCH_V4F_ET057/UCH_V50_ET057