RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Repair Manual

13B-51V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF007
CONTINUED 3
1.DEF
2.DEFNOTESThe fault is declared present or stored after an attempt to
start or after starting, with the engine cold, several hours
after the last trip (the difference in the coolant temperature
from the last engine stop and the present attempt to start
must be at least 60°C).
The level 1 warning light is on.
Check the condition of the rail pressure sensor connector (see Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2, component code 1032).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check that there are no external diesel leaks from the high pressure fuel circuit.
Check the continuity and for the absence of interference resistance on the following connections:
– connection code 3LZ between components 120 and 1032,
– connection code 3LX between components 120 and 1032,
– connection code 3LY between components 120 and 1032.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
With the ignition on and the engine stopped for over 1 minute:
View parameter PR038 Rail pressure.
– If the pressure is below 90 bar, the sensor is in order.
– If the pressure is above 90 bar, contact the Techline.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-52V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF011
PRESENT
OR
STOREDSENSOR FEED VOLTAGE NO. 1
1.DEF: Above max threshold
2.DEF: Below minimum threshold
NOTESConditions for applying the fault finding procedure to stored faults:
– The fault is declared present after:
– the ignition is switched on,
– starting the engine,
– a road test.
Special notes:
If the fault is present,
– thermoplunger cut-off,
– engine torque limited,
– the cruise control/speed limiter function is switched off,
– the EGR function is inhibited by the engine management computer,
– safe mode on the pedal sensor: use the value of gang 2 instead of gang 1.
The level 1 and European On Board Diagnostic warning lights are illuminated.
Use bornier Elé. 1681 for all operations on the connectors of the engine management
computer.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF011/EDC16C36_V4C_DF011/EDC16C36_V48_DF011/EDC16C36_V50_DF011/EDC16C36_V54_DF011/
EDC16C36_V58_DF011
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-53V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF011
CONTINUED 1
1.DEFNOTESNone.
Note:
Supply no.1 is for the following component:
– pedal sensor (gang 1),
– turbocharger pressure sensor.
Measure the feed voltage on the following sensors:
– Connection code 3LR of component 921.
– Connection code 3LQ of component 1071.
If the voltage is more than + 5.1 V, disconnect the sensor connectors one by one.
If, after disconnecting the pedal sensor, the voltage returns to normal,
Check the insulation against + 12 V of the following connection:
– Connection code 3LR between components 120 and 921.
If, after disconnecting the turbocharging pressure sensor, the voltage returns to normal,
Check the insulation against + 12 V of the following connection:
– connection code 3LQ, between components 120 and 1071.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Clear the faults created by the multiple disconnections.
Carefully examine the engine management computer connections (for conductive particles, bent pins).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-54V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF011
CONTINUED 2
2.DEFNOTESNone.
Note:
Supply no.1 is for the following component:
– pedal sensor (gang 1),
– turbocharger pressure sensor.
Measure the feed voltage on the following sensors:
– Connection code 3LR of component 921.
– Connection code 3LQ of component 1071.
If the voltage is less than + 4.9 V, disconnect the sensor connectors one by one.
If, after disconnecting the pedal sensor, the voltage returns to normal.
check the insulation to earth of the following connection:
– Connection code 3LR between components 120 and 921.
If, after disconnecting the turbocharging pressure sensor, the voltage returns to normal.
check the insulation to earth of the following connection:
– connection code 3LQ, between components 120 and 1071.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Clear the faults created by the multiple disconnections.
Carefully examine the engine management computer connections (for conductive particles, bent pins).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-55V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF012
PRESENT
OR
STOREDSENSOR SUPPLY VOLTAGE NO. 2
1.DEF: Above maximum threshold
2.DEF: Below minimum threshold
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after:
– the ignition is switched on,
– starting the engine,
– a road test.
Special notes:
If the fault is present:
– engine torque limited,
– the cruise control/speed limiter function is switched off,
– thermoplungers cut-off,
– air conditioning is switched off,
– the EGR function is inhibited by the engine management computer,
–The level 1 and European On Board Diagnostic warning lights are illuminated.
Use bornier Elé. 1681 for all operations on the engine management computer.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF012/EDC16C36_V4C_DF012/EDC16C36_V48_DF012/EDC16C36_V50_DF012/EDC16C36_V54_DF012/
EDC16C36_V58_DF012
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-56V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF012
CONTINUED 1
1.DEFNOTESNone.
Note:
Supply no.2 is for the following components:
– pedal sensor (gang 2),
– EGR valve position sensor,
– cruise control/speed limiter button (on steering wheel),
– refrigerant pressure sensor.
Measure the feed voltage on the following sensors:
– Connection code 3LU of component 921.
– Connection code 3AAQ of component 1290.
– Connection code 3GC of component 1460.
– Connection code 38Y of component 1202.
If the voltage is more than + 5.1 V, disconnect the sensor connectors one by one.
If, after disconnecting the pedal sensor, the voltage returns to normal,
Check the insulation against + 12 V of the following connection:
– connection code 3LU, between components120 and 921.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If, after disconnecting the EGR valve, the voltage returns to normal,
Check the insulation against + 12 V of the following connection:
– connection code 3GC between components 120 and 1460.
If, after disconnecting the differential pressure sensor, the voltage returns to normal,
Check the insulation against + 12 V of the following connection:
– connection code 3AAQ between components 120 and 1290.
If the voltage returns to normal after the coolant pressure sensor is disconnected,
Check the insulation against + 12 V of the following connection:
– Connection code 38Y between components 120 and 1202.
If the fault is still present, check the conformity of ET413 Cruise control/speed limiter function
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Clear the faults created by the multiple disconnections.
Carefully examine the engine management computer connections (for conductive particles, bent pins).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-57V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF012
CONTINUED 2
2.DEFNOTESNone.
Note:
Supply no.2 is for the following components:
– pedal sensor (gang 2),
– EGR valve position sensor,
– cruise control/speed limiter button (on steering wheel),
– refrigerant pressure sensor.
Measure the feed voltage on the following sensors:
– Connection code 3LU of component 921.
– Connection code 3AAQ of component 1290.
– Connection code 3GC of component 1460.
– Connection code 38Y of component 1202.
If the voltage is less than 4.9 V, disconnect the sensor connectors one by one.
If, after disconnecting the pedal sensor, the voltage is still too low,
Check the insulation to earth of the following connection:
– Connection code 3LU between components 120 and 921.
If, after disconnecting the EGR valve, the voltage returns to normal,
Check the insulation to earth of the following connection:
– Connection code 3GC between components 120 and 1460.
If, after disconnecting the differential pressure sensor, the voltage returns to normal,
Check the insulation to earth of the following connection:
– Connection code 3AAQ between components 120 and 1290.
If the voltage returns to normal after the coolant pressure sensor is disconnected,
Check the insulation against + 12 V of the following connection:
– Connection code 38Y between components 120 and 1202.
If the fault is still present, check the conformity of ET413 Cruise control/speed limiter function
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Clear the faults created by the multiple disconnections.
Carefully examine the engine management computer connections (for conductive particles, bent pins).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-58V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF013
PRESENT
OR
STOREDSENSOR SUPPLY VOLTAGE NO. 3
1.DEF: Above max threshold
2.DEF: Below minimum threshold
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after:
– the ignition is switched on,
– starting the engine,
– a road test.
Special notes:
If the fault is present,
– engine torque limited,
– the EGR function is inhibited by the engine management computer,
– turbocharger cut-off,
– increase in polluting emissions,
– the engine stops,
the level 2 and European On Board Diagnostic warning lights are lit.
Use bornier Elé. 1681 for all operations on the connectors of the engine management
computer.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
EDC16C36_V44_DF013/EDC16C36_V4C_DF013/EDC16C36_V48_DF013/EDC16C36_V50_DF013/EDC16C36_V54_DF013/
EDC16C36_V58_DF013
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-59V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF013
CONTINUED 1
1.DEFNOTESNone.
Note:
Supply no. 3 is for the following components:
– air flow sensor,
– rail pressure sensor.
Measure the feed voltage on the following sensors:
– Connection code 3KJ of component 799.
– Connection code 3LX of component 1032.
If the voltage is more than + 5.1 V, disconnect the sensor connectors one by one.
If, after disconnecting the air flow sensor, the voltage returns to normal,
Check the insulation against + 12 V of the following connection:
– Connection code 3KJ between components 120 and 799.
If, after disconnecting the rail pressure sensor, the voltage returns to normal,
Check the insulation against + 12 V of the following connection:
– connection code 3LX between components 120 and 1032.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Clear the faults created by the multiple disconnections.
Carefully examine the engine management computer connections (for conductive particles, bent pins).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-60V9 MR-372-J84-13B450$101.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF013
CONTINUED 2
2.DEFNOTESNone.
Note:
Supply no. 3 is for the following components:
– flow sensor,
– rail pressure sensor.
Measure the feed voltage on the following sensors:
– Connection code 3KJ of component 799.
– Connection code 3LX of component 1032.
If the voltage is below 4.9 V, disconnect the sensor connectors one by one.
If, after disconnecting the air flow sensor, the voltage returns to normal,
check the insulation to earth of the following connection:
– Connection code 3KJ between components 120 and 799.
If, after disconnecting the rail pressure sensor, the voltage returns to normal,
check the insulation to earth of the following connection:
– connection code 3LX between components 120 and 1032.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Clear the faults created by the multiple disconnections.
Carefully examine the engine management computer connections (for conductive particles, bent pins).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58