RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Owner's Manual

13B-21V9 MR-372-J84-13B450$050.mif
DIESEL INJECTION
Fault finding – Features13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Catalysed particle filter management (for F9Q816 engine only):
The particle filter prevents the escape of carbon particles emitted by the engine but not yet removed from the
exhaust gases.
The particle filter is a microporous structure containing channels arranged so as to force-filter the exhaust gases.
The exhaust pipe consists of several components:
– an oxidation catalytic converter mounted after the turbocharger. This catalytic converter ensures that HC/CO levels
meet current standards by generating the heat (rise in exhaust temperature caused by catalysis) required for
particle filter regeneration.
– a particle filter located under the body,
– a differential pressure sensor to inform the computer of the pressure difference upstream and downstream of the
particle filter
– a particle filter upstream temperature sensor,
– a particle filter downstream temperature sensor (only on certain F9Q816 engines in VDiag 48),
– a temperature sensor upstream of the turbine (TAVT).
During driving, the particle filter becomes loaded with particles of soot. When a given weight of soot determined by
computer mapping is reached, regeneration mode can be triggered if the maximum weight of soot in the particle filter
has not been reached and the engine operating conditions are met (coolant temperature, etc.)
Particle filter regeneration consists of burning the particles of soot that have accumulated in the filter.
The differential pressure sensor measures the particle filter inlet/outlet pressure differential; this measurement is
used to estimate the weight of soot present in the particle filter by mapping in the computer:
(soot weight = pressure differential as a function of exhaust volume flow rate).

13B-22V9 MR-372-J84-13B450$050.mif
DIESEL INJECTION
Fault finding – Features13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
If all the criteria are met, the computer enters regeneration mode. The injection programming is adjusted in order to
raise the target exhaust gas temperature between 550 and 650°C.
This temperature allows the particles accumulated in the filter to be partially or completely burnt (regenerated).
Regeneration efficiency depends on the particle filter inlet temperature and the time spent in regeneration mode.
Regeneration can be carried out automatically when driving if the weight of soot is less than 70 g and if the number
of regeneration attempts when driving is less than 11 (only for Vdiag 48).
If the weight of soot is greater than 70 g, the user will have to request an After-sales regeneration.
This regeneration is carried out in the workshop. Always follow the instructions written in the interpretation of
commands (SC017 Particle filter regeneration) to perform regeneration in complete safety.
After an After-sales regeneration, always reconfigure certain parameters in the computer using command SC036
Reinitialise programming (see "interpretation of commands").
Warning light management:
Instrument panel display
The computer displays certain information on the instrument panel relating to engine operation. This involves six
functions:
– the pre-postheating warning light,
– the coolant temperature warning message,
– the level 1 fault warning light (non-critical fault),
– the level 2 fault warning light (emergency stop),
– the OBD warning light (European On Board Diagnostic),
– the particle filter specific warning light (F9Q816 engine only).
These six functions are represented by 6 warning lights and/or messages displayed by the on-board computer.
In addition, certain warning lights are, when lit, accompanied by a spoken message on vehicles fitted with a voice
synthesiser (refer to the driver's handbook).
A 3 second visual inspection (automatic test procedure managed by the instrument panel) is carried out by the
injection computer when the ignition is switched on.IMPORTANT
The particle filter must be replaced after a period of time which largely depends on the grade of engine oil used -
this information is in the driver's handbook.
After replacing it, always reconfigure certain parameters in the computer using command SC036 Reinitialise
programming (see "interpretation of commands").

13B-23V9 MR-372-J84-13B450$050.mif
DIESEL INJECTION
Fault finding – Features13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Orange pre-postheating warning light
This warning light is used as an in-operation indicator lamp:
– Continuously lit under + after ignition feed: indicates preheating of the heater plugs.
It goes out when preheating is complete and the engine is able to start.
Orange "SERVICE" non-critical fault warning light (level 1)
This warning light is used to indicate a fault in the system:
– Continuously lit with the CHECK INJECTION message:
Indicates a level 1 fault (involving operation of the injection system in defect mode).
The driver should have the repairs carried out as soon as possible.
Temperature/red emergency STOP (level 2) warning light
This indicator light is used both as an in-operation indicator light and as a system fault warning light.
– Intermittently lit with the ENGINE OVERHEATING message:
Indicates that the coolant temperature is too high (the driver is free to stop the vehicle or not).
– Continuously lit with the INJECTION FAULT: STOP THE ENGINE message and an audible beep indicates a level
2 fault.
In that case, the vehicle must be stopped immediately (when traffic conditions allow).
The driver should carry out repairs as soon as possible.
European On Board Diagnostic excess pollution ORANGE warning light
Engine symbol with the CHECK EMISSION CONTROL message.
This warning light comes on if the system has one or more OBD faults.
This warning light is used to alert the driver to injection faults that could lead to excessive pollution, or if the EOBD
system (European On Board Diagnostic) has been deactivated.
The injection computer requests illumination of the OBD warning light for a present fault only after three successive
driving cycles.
The driver should have the repairs carried out as soon as possible.

13B-24V9 MR-372-J84-13B450$050.mif
DIESEL INJECTION
Fault finding – Features13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
ORANGE particle filter specific warning light (F9Q816 engine only):
F9Q816 Vdiag 48 engines:
This warning light is used to warn the driver that the particle filter is loaded with particles (weight of soot greater than
36 g or more than 6 regeneration failures while driving due to driving conditions not being favourable for
regeneration). As soon as possible the driver must then drive at an average speed of 48 mph (80 km/h) subject to
the road conditions and authorised speed limits.
F9Q816 Vdiag 50 engines:
This warning light is used to warn the driver that the particle filter is loaded with particles.
European On Board Diagnostic management:
The OBD (On Board Diagnostic) system permits detection of any faults relating to the vehicle emission control
system (OBD EURO IV emission control standards being exceeded).
This system should be active for the entire life of the vehicle.
1. Conditions of an OBD fault appearing
An OBD fault will be detected after 3 trip cycles.
It allows the driver to know whether the vehicle has a fault directly linked to the emission control system.
2. System faults displayed by the OBD
List of the faults recorded by the OBD system:
– DF002 Air temperature sensor circuit.
– DF004 Turbocharging pressure sensor circuit.
– DF011 Sensor supply voltage no. 1.
– DF012 Sensor supply voltage no. 2.
– DF013 Sensor supply voltage no. 3.
– DF026 Cylinder 1 injector control circuit.
– DF027 Cylinder 2 injector control circuit.
– DF028 Cylinder 3 injector control circuit.
– DF029 Cylinder 4 injector control circuit.
– DF054 Turbocharging solenoid valve control circuit.
– DF055 Turbocharging pressure regulation circuit.

13B-25V9 MR-372-J84-13B450$050.mif
DIESEL INJECTION
Fault finding – Features13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
– DF056 Air flowmeter circuit.
– DF107 Computer memory.
– DF200 Atmospheric pressure sensor.
– DF209 EGR valve position sensor circuit.
– DF272 EGR valve control circuit.
– DF310 Particle filter upstream temp.* sensor
– DF315 Particle filter diff.* pressure sensor
– DF316 Particle filter diff* pressure
– DF647 EGR valve position regulation.
Some repair operations require programming to ensure that certain engine components function correctly.
Follow the programming procedures (see Replacement of components), if replacing the exhaust gas
recirculation valve or an injector.
*temp: temperature
* diff: differential
3. Conditions for deleting an OBD fault
An OBD fault is deleted in several phases.
The fault present on the diagnostic tool will only become stored (after a repair operation) after the vehicle has
been driven 3 times.
The OBD warning light will only go out after these 3 trips.
The instrument panel warning light coming on does not automatically mean that the system has a fault.
In order for the OBD fault and display parameters to be cleared from the computer, the system requires
40 engine heating cycles.
An engine heating cycle is a driving cycle during which:
– the engine coolant temperature reaches at least 71.1°C,
– the engine coolant temperature varies by 22.2°C in relation to the engine starting temperature.
If one of these conditions is not fulfilled, the OBD fault will still be present or stored on the injection
computer.

13B-26V9 MR-372-J84-13B450$060.mif
13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
No.
Defect
modesCause of fault Customer perception
Engine stop– Flow regulator short circuit to earth (flow regulator closed).
– High pressure circuit leak (min. rail pressure).
– Injector jammed open.
– Loss of engine speed signal.
– Sensor feed No.No. 3 fault.
– Engine management computer internal fault.
– Injector row 1 and 2 fault.
– Solenoid control stage cut-off fault caused by computer
initialisation (to check that cut-off is operational).Engine stop
Level 2 on
Limited torque– Rail pressure sensor fault.
– Pedal sensor gangs 1 and 2 double fault (including sensor feeds
1 and 2).
– Open circuit, short circuit to earth and turbocharger solenoid valve
short circuit to + 12 V.
– Turbocharger pressure sensor fault (sensor signal short circuit
with sensor feed, sensor signal short circuit to +12volts, sensor
open circuit to earth, sensor signal short circuit to earth, sensor
feed open circuit, sensor signal open circuit, significant line
resistance on sensor feed, significant line resistance on sensor
signal, significant line resistance on sensor earth, significant
pressure difference measured between the atmospheric pressure
sensor and the turbocharger pressure sensor at idle speed).
– Injector codes fault.
– Computer internal fault.
– Solenoid control stage cut-off fault caused by computer
initialisation (to check that cut-off is operational).
– Sensor feed 1, 2 and 3 fault.
– Vehicle speed fault.Speed limited
to≈1750 rpm
Loss of engine torque
Flow/injected
quantity
limited– Flow regulator open circuit or short circuit to + 12 volts
(Flow regulator open).
– Positive rail pressure loop difference (measurement < setpoint).
– Negative rail pressure loop difference (measurement > setpoint).
– Max. rail pressure (flow regulator jammed in open position).Limited performance
Pedal limp
home– Pedal sensor gangs 1 and 2 double fault (including sensor feeds
1 and 2).
– Activation of pedal safety programming.
– Accelerator pedal mechanism jammed.Speed limited to
45-48 mph (75-80 km/h)
DIESEL INJECTION
Fault finding – Defect modes

13B-27V9 MR-372-J84-13B450$060.mif
DIESEL INJECTION
Fault finding – Defect modes13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
* normally aspirated: naturally aspiratedDefect
modesCause of fault Customer perception
Turbocharger
cut-off– Turbocharging pressure loop difference (vanes jammed,
compressor/turbine fault, turbocharging pressure sensor fault,
sensor connection fault, functional solenoid valve fault
(disconnected, hose kinked, solenoid valve mechanism jammed),
high pressure circuit leak (high pressure hose, major distributor
leak).
– Flowmeter failure (plausibility of the reading):
– significant line resistance on earth sensor,
– significant line resistance on sensor feed, significant line resistance
on sensor signal,
– flowmeter sensing element damaged,
– wiring/connection fault,
– flowmeter voltage or 5 V reference voltage deviation.
– Flowmeter failure (plausibility of sensitivity variation):
– flowmeter clogged/flow underestimated,
– flow overestimated,
– air circuit leak between flowmeter and compressor,
– air circuit leak after compressor.
– Electrical faults:
– signal short circuit to + 12 V,
– signal short circuit to earth,
– signal open circuit,
– sensor feed open circuit,
– open circuit, short circuit to earth and turbocharger solenoid valve
short circuit to + 12 V.
– Turbocharger pressure sensor fault (sensor signal short circuit with
sensor feed, sensor signal short circuit to + 12 V, sensor open
circuit to earth, sensor signal short circuit to earth, sensor feed open
circuit, sensor signal open circuit, significant line resistance on
sensor feed, significant line resistance on sensor signal, significant
line resistance on sensor earth, significant pressure difference
measured between the atmospheric pressure sensor and the
turbocharger pressure sensor at idle speed).
– EGR valve fault (valve clogged, valve jammed open).
– Camshaft sensor fault.
– Engine speed sensor fault.
– Sensor feed No. 1 fault.25-50% loss of engine
performance (normally
aspirated engine)
Rail pressure
limited– Rail pressure sensor fault.
– Sensor feed No. 3 fault.Poor performance
Rail pressure
reduction
– Positive rail pressure loop difference (measurement < setpoint).
Poor performance

13B-28V9 MR-372-J84-13B450$070.mif
13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Summary of available configuration readings
NOTESConfiguration readings are used to check the state of configurations performed.
The configuration readings cannot be changed.
The computer is configured as soon as the one of the vehicle's optional system
components is operated.
In the event of a fault, consult the interpretation of command RZ005 Programming.
LC009Air conditioning
WITH OR WITHOUT
LC056Heating elements
WITH OR WITHOUT
LC065Water in diesel fuel sensor
WITH OR WITHOUT
LC120Cruise control
WITH OR WITHOUT
LC121Speed limiter
WITH OR WITHOUT
DIESEL INJECTION
Fault finding – Configuration and programming

13B-29V9 MR-372-J84-13B450$080.mif
13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
COMPUTER REPLACEMENT OR REPROGRAMMING
Two operations must be performed when replacing or reprogramming the computer:
SC003 Save computer data and SC001 Enter saved data.
–Run SC003 Save computer data before replacing or reprogramming the computer. This enables certain data
to be saved in the diagnostic tool so that the new computer* can be reconfigured like the old one. The saved data
are: injector codes, EGR programming, vehicle options.
–Run SC001 Enter saved data after replacing or reprogramming the computer. This enables the data (saved by
the command SC003 Save computer data) to be rewritten in the new computer*.
If you cannot establish dialogue with the computer being replaced: you will not be able to save anything.
After replacing the computer, write the IMA codes of each injector manually using command SC002 Enter injector
codes by reading the code on each injector (see Replacing the injectors).
Only on F9Q816 engines:
– Enter the data specific to particle filter operation by running SC036 Reinitialise programming and selecting after
replacing injection computer with no save option.
Exhaust gas recirculation valve data is programmed automatically the 1st time the new computer is turned on*.
* New computer or reprogrammed computer.
Specific to the cruise control/speed limiter operation to be carried out before reprogramming of the computer:
Before reprogramming the injection computer, move the main Cruise control/Speed limiter switch to the rest
position. The information about the cruise control or the speed limiter displayed on the instrument panel
disappears.
Otherwise, if the main switch remains in the cruise control or speed limiter position during and after reprogramming,
the Cruise control/Speed limiter function will not be operational.
The procedure for resetting the function is as follows:
– Vehicle ignition on.
– Position the main switch in rest position (the computer then detects the rest position).
– Position the switch in Cruise control position to activate the Cruise control function.
– Position the switch in Speed limiter position to activate the Speed limiter function. IMPORTANT
– Switch on the diagnostic tool (mains or cigarette lighter supply).
– Connect a battery charger.
– Cut off all the electrical consumers (lights, interior lighting, air conditioning, radio CD, etc.).
– Wait for the engine to cool (engine coolant temperature < 60° and air temperature < 50°).
– During (re)programming, the instrument panel screen displays "Oil pressure fault".
Ignore this message and do not take any action in connection with it.
DIESEL INJECTION
Fault finding – Replacement of components

13B-30V9 MR-372-J84-13B450$080.mif
DIESEL INJECTION
Fault finding – Replacement of components13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
PROCEDURE:
Before replacing or reprogramming the computer:
–Select SC003 Save computer data,
– if the following message appears: a saved file exists; do you want to overwrite this data?: (this file corresponds
to the last save carried out on the tool)
–select "YES".
When the save has been performed, replace the computer or carry out the programming then proceed to the next
step.
After replacing or reprogramming the computer:
–Select SC001 Enter saved data, then follow the instructions given by the diagnostic tool,
– if the VIN is not entered (see Computer identification on the main screen),
–select VP010 Enter VIN,
When both these commands have finished:
– Switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes) Communication lost
with computer: EDC16 C36, check the tool connection and computer power supply before switching the
ignition back on.
(The powerlatch duration depends on the coolant temperature and activation time of the turbocharger
coolant pump. This operation finishes when the pump is deactivated.)
– then check the system faults, and clear any stored faults,
– if there are faults, deal with the present faults,
– clear the faults from the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
End of the procedure.IMPORTANT
– The injection computer retains the immobiliser code for life.
– The system has no security code.
– It is forbidden to perform tests with computers borrowed from the Parts Department or from another vehicle
which must then be returned.
– These computers are hard-coded.
– If the injection computer appears to be faulty, contact the Techline and refer to the fault finding log.