RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Repair Manual

13B-51
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF039
PRESENTINLET AIR TEMPERATURE SENSOR CIRCUITCO.1: Open circuit or short circuit to + 12 volts.
CC.0: Short circuit to earth.
NOTESPriority when dealing with a number of faults:
– Deal with fault DF113 Sensor supply voltage first.
Check the connection and condition of the 4-track connector of the air temperature sensor.
Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Measure the resistance between tracks 1 and 2 on the air temperature sensor.
Replace the air temperature sensor if the resistance is not 2051 Ω +
120 Ω at 25°C.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 1 Track C3 computer connector B
Sensor connector track 2 Track J2 computer connector B
Sensor connector track 3 Track C1 computer connector B
Sensor connector track 4 Track C2 computer connector B
Repair if necessary.
DDCR_V44_DF039P/DDCR_V48_DF039P

13B-52
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF047
STOREDCOMPUTER SUPPLY VOLTAGE1.DEF: Above maximum threshold.
2.DEF: Below minimum threshold.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine running above 1000 rpm.
Measure the battery voltage when the ignition is switched on.
If the battery voltage < 10 V recharge the battery.
Check the condition and connection of the battery terminals.
Repair if necessary.
Check the vehicle's charging circuit.
Repair if necessary.
Check the connection and condition of the black 32-track computer connector A.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
+ after ignition feed. Track D1 computer connector A
Chassis earth Tracks G4 and H4 computer connector A
Repair if necessary.
DDCR_V44_DF047M/DDCR_V48_DF039P

13B-53
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF049
STOREDREFRIGERANT SENSOR CIRCUITCO.1: Open circuit or short circuit to + 12 volts.
CC.0: Short circuit to earth.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present when the engine is running and the air conditioning is on.
Priority when dealing with several faults: - Deal first with fault DF113 Sensor supply
voltage.
Check the connection and condition of the refrigerant pressure sensor connector.
Repair if necessary.
Check the connection and condition of the computer's 32-track grey connector C.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track BTrack C4 computer connector C
Sensor connector track CTrack C3 computer connector C
Sensor connector track ATrack C3 computer connector C
Repair if necessary.
DDCR_V44_DF049M/DDCR_V48_DF049M

13B-54
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF050
PRESENT
OR
STOREDBRAKE SWITCH CIRCUIT
1.DEF: No signal.
2.DEF: Inconsistency.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present when the ignition is switched on, when decelerating or when
the brake pedal is depressed.
Deal with the fault even if it is stored.
Check the connection and condition of the switch connector.
Repair if necessary.
Check for the +12 V feed on the switch supply.
Repair if necessary.
Check the connection and condition of the black 32-track connector A and grey 32-track connector C of the
computer.
Repair if necessary.
Check that the switch is working.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Brake light switch track 1 and 3 + after ignition feed.
Brake light switch track 4Track E4 computer connector A
Repair if necessary.
DDCR_V44_DF050/DDCR_V48_DF050

13B-55
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF051
PRESENTCRUISE CONTROL/SPEED LIMITER FUNCTION1.DEF: inconsistency.
2.DEF: On/off switch.
NOTESNone.
Check the connection and condition of the black 32-track computer connector A.
Repair if necessary.
Check the connection and condition of the connections of the on - off control switch of the cruise control - speed
limiter function.
Repair if necessary.
Check for the 12 V after ignition feed on track A2 of the on - off switch of the cruise control - speed limiter
function.
Repair if necessary.
Carry out an operating check on the cruise control/speed limiter function on/off switch (consult the
interpretation of ET042 Cruise control/speed limiter).
If the fault is still present, contact the Techline.
DDCR_V44_DF051P/DDCR_V48_DF051P

13B-56
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF052
PRESENTINJECTORS CONTROL CIRCUITCC.1: Short circuit to +12 volts.
CC.0: Short circuit to earth.
NOTESPriority when dealing with a number of faults:
In the event of a combination of faults DF052 and DF026, DF027, DF028, and DF029,
the fault finding procedure remains the same in order to determine the faulty injector.
Special notes:
The engine stalls when the fault appears. The level 1 warning light illuminates along
with the message Faulty injection.
Switch off the ignition, check the condition and connection of the injector connectors.
Repair if necessary.
Switch off the ignition, disconnect the injectors (or the injector identified by DF026, DF027, DF028, DF029)
and switch the ignition back on.
Using the diagnostic tool, check for changes to DF052.
Is DF052 present or stored?
DF052
presentThe injectors are not defective.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on
the following connections:
Injector 1 track 1 (+)Track A4, computer connector B
Injector 1 track 2 (earth)Track B4 computer connector B
Injector 2 track 1 (+)Track G4 computer connector B
Injector 2 track 2 (earth)Track H4 computer connector B
Injector 3 track 1 (+)Track C4 computer connector B
Injector 3 track 2 (earth)Track D4 computer connector B
Injector 4 track 1 (+)Track E4 computer connector B
Injector 4 track 2 (earth)Track F4 computer connector B
Repair if necessary.
If the fault is still present, contact the Techline.
DDCR_V44_DF052/DDCR_V48_DF052

13B-57
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF052
CONTINUEDINJECTORS CONTROL CIRCUITCC.1: Short circuit to +12 volts.
CC.0: Short circuit to earth.
DF052
storedInjector(s) defective.
Replace the injector identified by DF026 to DF029 if present.
If none of the faults identifying the defective injector circuit are present:
– Switch off the ignition.
– Reconnect one of the four injectors.
– Switch the ignition back on and, if the fault reappears as present, replace the
reconnected injector.
Carry out the same procedure for the remaining injectors.

13B-58
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
13B
DDCR INJECTION
Vdiag No.: 44, 48
DF053
STOREDRAIL PRESSURE REGULATION FUNCTION
1.DEF: At minimum limit
2.DEF: At maximum limit
3.DEF: Below minimum threshold
4.DEF: Above maximum threshold
5.DEF: High flow current < minimum
6.DEF: High flow current > maximum
7.DEF: Low flow current < minimum
8.DEF: Low flow current > minimum
NOTESSpecial notes:
If DF053, the engine may stop, with the level 1 and 2 warning lights illuminated along
with the message Faulty injection.
Priority when dealing with a number of faults:
– DF007 Rail pressure sensor circuit,
– DF098. Fuel temperature sensor circuit.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
4.DEF
6.DEF
8.DEF
NOTESNone.
Check the connection and condition of the fuel flow actuator connector (brown IMV connector on the pump).
Repair if necessary.
Measure the resistance between tracks 1 and 2 of the flow actuator.
Replace the flow actuator if the resistance is not 5.3 Ω +
0.5 Ω at 20°C.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check the insulation, continuity, and the absence of interference resistance on the following connection:
Computer connector B track M4 Track 1 fuel flow actuator
Repair if necessary.
Check that there is fuel present in the tank and that it is correct. Run Test 13 Diesel fuel conformity check.
Run Test 1 Low pressure circuit check.
DDCR_V44_DF053M/DDCR_V48_DF053M
DIESEL INJECTION
Fault finding – Interpretation of faults

13B-59
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF053
CONTINUED
1.DEF - 2.DEF
3.DEF - 5.DEF
7.DEF
NOTESNone.
Check that there is fuel present in the tank and that it is correct. Run Test 13 Diesel fuel conformity check.
Run Test 1 Low pressure circuit check.
Run Test 6 High pressure system check.

13B-60
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF054
STOREDTURBOCHARGING SOLENOID VALVE CONTROL CIRCUITCO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 volts
1.DEF: At minimum limit
2.DEF: At maximum limit
NOTESSpecial notes:
If DF054, the performance of the vehicle is adversely affected and the level 1 warning
light illuminates along with the message Faulty injection.
Check the condition of the air filter, and replace it if necessary.
Check that the inlet manifold is not blocked (clogged).
Check that the turbocharger is working properly, and carry out any necessary repairs.
Check the connection and condition of the 2-track connector of the turbocharging solenoid valve.
Repair if necessary.
Check for +12 V on track 2 of the solenoid valve.
Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check the continuity, insulation, and the absence of interference resistance on the following connections:
Solenoid valve connector track 2 + after ignition feed
Solenoid valve connector track 1 Track M2 computer connector B
Repair if necessary.
Run TEST 11 Air line at the turbocharger.
Run TEST 10 Turbocharger control solenoid valve check.
Run TEST 12 Turbocharger.
If the fault persists, replace the turbocharging solenoid valve.
DDCR_V44_DF054M/DDCR_V48_DF054M