RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Repair Manual

13B-61
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF056
PRESENT
OR
STOREDAIR FLOW SENSOR CIRCUIT1.DEF: Permanent low level
2.DEF: Permanent high signal
3.DEF: Below minimum threshold
4.DEF: Above maximum threshold
5.DEF: At minimum limit
6.DEF: At maximum limit
NOTESPriority when dealing with a number of faults:
– DF054 Turbocharging solenoid valve control circuit.
– DF113 Sensor supply voltage.
Conditions for applying fault finding procedures to stored faults:
the fault reappears after the faults have been cleared followed by a road test.
Check the condition of the air filter, and replace it if necessary.
Check that the inlet manifold is not blocked (clogged).
Check that the turbocharger is working properly.
Run TEST 11 Air line at the turbocharger.
Run TEST 10 Turbocharger control solenoid valve check.
Run TEST 12 Turbocharger.
Carry out the necessary repairs.
Check the connection and condition of the 6-track connector of the air flow sensor.
Repair if necessary.
Check for +5 V after ignition feed on track 3 of the sensor connector.
Repair if necessary.
Check for +12 V on track 4 of the sensor connector.
Repair if necessary.
Check for earth on connector track 6.
Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
DDCR_V44_DF056/DDCR_V48_DF056

13B-62
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF056
CONTINUED
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 1 Track K2 computer connector B
Sensor connector track 2 Track A3 computer connector B
Sensor connector track 3 Track A1 computer connector B
Sensor connector track 4 Track A2 computer connector B
Sensor connector track 5 + after ignition feed
Sensor connector track 6Earth
Repair if necessary.
Also check the insulation between these connections.
If the fault is still present, replace the air flow sensor.

13B-63
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF057
STOREDWATER IN DIESEL FUEL DETECTOR CIRCUITCO.1: Open circuit or short circuit to +12 volts
CC.0: Short circuit to earth
1.DEF: Above maximum threshold (water present)
NOTESConditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
The level 1 warning light illuminates along with the message Check diesel filter.
CO.1
CC.0
NOTESNone.
Check for water in the diesel filter. Clean and replace the filter if necessary.
Check the condition and connection of the 3-track connector of the water detector.
Repair if necessary.
Check the connection and condition of the grey 32-track connector C of the computer.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 3 Earth
Sensor connector track 2 Track B3 computer connector C
Sensor connector track 1 Track A3 computer connector B
Repair if necessary.
1.DEF
NOTESNone.
Bleed the diesel filter.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
DDCR_V44_DF057M/DDCR_V48_DF057M

13B-64
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF059
STOREDCOMBUSTION MISFIRES ON CYLINDER 1
NOTESSpecial notes:
If DF059, the engine speed is maintained at 1000 rpm, the engine performance is
reduced to 75%, and the level 1 warning light illuminates along with the message
Faulty injection.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Priority when dealing with a number of faults:
– DF026 Cylinder 1 injector control circuit (CC or CO).
– DF053 Pressure regulation.
Run TEST 13 Diesel fuel conformity check.
Run TEST 3 Injector check.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
Check the inlet ducts and the EGR valve, and clean them if necessary.
Replace the injector.
DDCR_V44_DF059M/DDCR_V48_DF059M

13B-65
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF060
STOREDMISFIRING ON CYLINDER 2
NOTESSpecial notes:
If DF060, the engine speed is maintained at 1000 rpm, the engine performance is
reduced to 75%, and the level 1 warning light illuminates along with the message
Faulty injection.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Priority when dealing with a number of faults:
– DF027 Cylinder 2 injector control circuit (CC or CO).
– DF053 Pressure regulation.
Run TEST 13 Diesel fuel conformity check.
Run TEST 3 Injector check.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
Check the inlet ducts and the EGR valve, and clean them if necessary.
Replace the injector.
DDCR_V44_DF060M/DDCR_V48_DF060M

13B-66
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF061
STOREDMISFIRING ON CYLINDER 3
NOTESSpecial notes:
If DF061, the engine speed is maintained at 1000 rpm, the engine performance is
reduced to 75%, and the level 1 warning light illuminates along with the message
Faulty injection.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Priority when dealing with a number of faults:
– DF028 Cylinder 3 injector control circuit (CC or CO).
– DF053 Pressure regulation.
Run TEST 13 Diesel fuel conformity check.
Run TEST 3 Injector check.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
Check the inlet ducts and the EGR valve, and clean them if necessary.
Replace the injector.
DDCR_V44_DF061M/DDCR_V48_DF061M

13B-67
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF062
STOREDMISFIRING ON CYLINDER 4
NOTESSpecial notes:
If DF062, the engine speed is maintained at 1000 rpm, the engine performance is
reduced to 75%, and the level 1 warning light illuminates along with the message
Faulty injection.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Priority when dealing with a number of faults:
– DF029 Cylinder 4 injector control circuit (CC or CO).
– DF053 Pressure regulation.
Run TEST 13 Diesel fuel conformity check.
Run TEST 3 Injector check.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
Check the inlet ducts and the EGR valve, and clean them if necessary.
Replace the injector.
DDCR_V44_DF062M/DDCR_V48_DF062M

13B-68
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF089
PRESENTINLET MANIFOLD PRESSURE SENSOR CIRCUIT
1.DEF: Permanent low level
2.DEF: Permanent high level
3.DEF: Below minimum threshold
4.DEF: Above maximum threshold
5.DEF: Inconsistency
6.DEF: At maximum limit
7.DEF: At minimum limit
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Special notes:
The level 1 warning light illuminates along with the message Faulty injection.
K9K 722 ENGINE
1.DEF-2.DEF
3.DEF-4.DEF
NOTESNone.
Check the connection and condition of the 4-track connector of the inlet pressure sensor.
Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 1 track C3 computer connector B
Sensor connector track 2 track J2 computer connector B
Sensor connector track 3 track C1 computer connector B
Sensor connector track 4 track C2 computer connector B
Repair if necessary.
DDCR_V44_DF089P/DDCR_V48_DF089P

13B-69
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF089
CONTINUED 1
5.DEF-6.DEF
7.DEFNOTESNone.
Visually check the turbocharging circuit sealing.
Run TEST 11 Air line at the turbocharger.
Repair if necessary.
Remove the air supply ducts and check that they are not blocked.
Repair if necessary.
Check for consistency between the atmospheric pressure and the manifold pressure (PR035 = PR032).
With the engine stopped, the pressure should be approximately the same between the 2 sensors.
Replace the manifold pressure sensor if necessary.
Check the turbocharger,
Run TEST 10 Turbocharger control solenoid valve check.
Run TEST 12 Turbocharger.
Repair if necessary.

13B-70
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF089
CONTINUED 2
K9K 728 ENGINE
1.DEF-2.DEF
3.DEF-4.DEF
NOTESNone.
Check the connection and condition of the 4-track connector of the inlet pressure sensor.
Repair if necessary.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 1 track C3 computer connector B
Sensor connector track 2 track J2 computer connector B
Sensor connector track 3 track C1 computer connector B
Sensor connector track 4 track C2 computer connector B
Repair if necessary.
5.DEF
6.DEF - 7.DEF
NOTESNone.
Visually check the turbocharging circuit sealing,
Run TEST 11 Air line at the turbocharger.
Repair if necessary.
Remove the air supply ducts and check that they are not blocked.
Repair if necessary.
Check for consistency between the atmospheric pressure and the manifold pressure (PR035 = PR032).
With the engine stopped, the pressure should be approximately the same between the 2 sensors.
Replace the manifold pressure sensor if necessary.
In case of 6.DEF and 7.DEF, check the turbocharger.
Run TEST 10 Turbocharger control solenoid valve check.
Run TEST 12 Turbocharger.
Repair if necessary