RENAULT TWINGO 2009 2.G Chasiss Workshop Manual

35A-11
WHEELS AND TYRES
Wheel rim: Identification
35A
IDENTIFICATION
1 - Marking
There are two types of identification marking on the
wheel rims:
-engraved marking for steel wheel rims,
-cast marking for alloy wheel rims.
The marking gives the main dimensional specifications
of the wheel rim.
This marking may be:
-complete, for example 6 J 15 5 CH 36,
-simplified, for example 6 J 15.
There are 3 types of wheel rim edges (2) :
-those with two flat edges,
-those with two raised edges,
-those with one flat edge and one raised edge.2 - Installation diameter for the wheel bolts
The wheel bolts are positioned with a pitch circle dia-
meter of:
-5 holes: 108 mm,
-4 holes: 100 mm.
3 - Rim run-out
The maximum run-out is measured at the wheel rim
edge (7) .
Steel wheel rims: 0.8 mm
Alloy wheel rims: 0.3 mm
4 - Out-of-roundness
The maximum out-of-round value is measured on the
tyre bead bearing surface.
0.7 mm Wheel type 6 J 15
1Width (in inches) 6
2Rim edge profile J
3Nominal diameter (in inches) 15
4Number of holes 5
5Anchorage profile of the tyre CH
6Offset (in mm) 36
100988

36A-1
STEERING ASSEMBLY
Steering box: Removal - Refitting
36A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
aRemove:
-the front wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) ,
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the « subframe - front driveshaft lower arm - power-
assisted steering box - front anti-roll bar » assem-
bly (see 31A, Front axle components, Front axle
subframe: Removal - Refitting, page 31A-43) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the power-assisted steering box bolts (1) ,
-the power-assisted steering box.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the power-assisted steering box,
-the power-assisted steering box bolts.
aTorque tighten the power-assisted steering box
bolts (105 Nm).
II - FINAL OPERATION.
aRefit:
-the « subframe - front driveshaft lower arm - power-
assisted steering box - front anti-roll bar » assem-
bly (see 31A, Front axle components, Front axle
subframe: Removal - Refitting, page 31A-43) ,
-the wheel arch liners (see Front wheel arch liner:
Removal - Refitting) (55A, Exterior protection),
-the front wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
aCheck the axle geometry (see 30A, General infor-
mation, Axle assemblies: Check, page 30A-23) .
aIf necessary, adjust the axle assemblies' geometry
(see 30A, General information, Front axle sys-
tem: Adjustment, page 30A-36) . Tightening torquesm
power-assisted steering
box bolts105 Nm
119405

36A-2
STEERING ASSEMBLY
Track rod: Removal - Refitting
36A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove the front wheel (see 35A, Wheels and ty-
res, Wheel: Removal - Refitting, page 35A-1) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aLoosen the wheel alignment adjustment lock nut (1)
.
aRemove the track rod ball joint nut (2) .aExtract the ball joint using (3) (Tav. 476).
aUnscrew the track rod anti-clockwise and note the
number of turns for refitting.
aRemove the track rod.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aScrew the track rod back in place by the number of
turns noted during removal.
aFit the track rod end in the hub carrier.
aRefit the track rod ball joint nut.
aTighten to torque:
-the track rod ball joint nut (37 N.m),
-the wheel alignment adjusting lock nut (53
N.m).
II - FINAL OPERATION
aRefit the wheel (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
aCheck the axle geometry (see 30A, General infor-
mation, Axle assemblies: Check, page 30A-23) .
aIf necessary, adjust the geometry of the axle assem-
blies (see 30A, General information, Front axle
system: Adjustment, page 30A-36) . Special tooling required
Tav. 476Ball joint extractor.
Tightening torquesm
track rod ball joint nut37 N.m
wheel alignment adjust-
ing lock nut53 N.m
IMPORTANT
Consult the safety and cleanliness advice and oper-
ation recommendations before carrying out any
repair (see Steering: Precautions for the repair) .
122722
122713

36A-3
STEERING ASSEMBLY
Track rod: Removal - Refitting
36A

36A-4
STEERING ASSEMBLY
Axial ball joint linkage: Removal - Refitting
36A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
a
aApply the before repair procedure using the dia-
gnostic tool:
-connect the diagnostic tool,
-select the airbag computer,
-go to repair mode,
-apply the "before repair procedure".
aRemove:
-the front wheel on the side in question (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) ,
-the track rod (see 36A, Steering assembly, Track
rod: Removal - Refitting, page 36A-2) ,
-the steering box gaiter (see 36A, Steering assem-
bly, Steering box gaiter: Removal - Refitting,
page 36A-16) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aLock the wheels to disengage the rod teeth on the
valve side.aSet up the (Dir. 1306-03) (1) on the steering rack, at
the pinion end.
aUnlock the axial ball joint using tool (Dir. 1305-01)
(2) .
aRemove the axial ball joint.
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace the following after each removal
operation:
-the limiter (3) ,
-the steering box gaiter. Special tooling required
Dir. 1306-03Steering r ack locking tool.
Dir. 1305-01Tool for removal - refitting of
the axial ball joint (diameter
35 mm to 41 mm).
Tightening torquesm
axial ball joint50 Nm
Note:
It is necessary to lock the airbag computer in
order to unlock the steering column.
97469
116991
Note:
Before refitting the new track rods, inser t a 12 x
100 tap into the threading at the ends of the
steer ing rack in order to remove any trace of
FRENETANCHE from the original fitting and so
pre vent seizure of the threaded sections on refit-
ting.

36A-5
STEERING ASSEMBLY
Axial ball joint linkage: Removal - Refitting
36A
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit on the steering rack:
-the limiter,
-the axial ball joint whose threading has been coat-
ed with HIGH RESISTANCE THREAD LOCK.
aTorque tighten the axial ball joint (50 Nm) using the
(Dir. 1305-01) (2) .
aRemove the (Dir. 1306-03) (1) from the steering
rack on the pinion end.
III - FINAL OPERATION
aRefit:
-the steering box gaiter (see 36A, Steering assem-
bly, Steering box gaiter: Removal - Refitting,
page 36A-16) ,
-the track rod (see 36A, Steering assembly, Track
rod: Removal - Refitting, page 36A-2) ,
-the front wheel on the side in question (see 35A,
Wheels and tyres, Wheel: Removal - Refitting,
page 35A-1) .
a
aApply the before repair procedure using the dia-
gnostic tool:
-connect the diagnostic tool,
-select the airbag computer,
-go to repair mode,
-apply the "after repair procedure".
aCheck the settings of the axle assemblies (see 30A,
General information, Front axle system: Adjust-
ment, page 30A-36) .
aIf necessary, adjust the geometry of the axle assem-
blies (see 30A, General information, Front axle
system: Adjustment, page 30A-36) . Note:
It is necessary to unlock the airbag computer in
order to lock the steering column.

36A-6
STEERING ASSEMBLY
Steering column: List and location of components
36A
MANUAL STEERING
119647
(1) inter mediate shaft
(2) key-operated switch
(3) the steering column
POWER ASSISTED STEERING
121129
(1) inter mediate shaft
(2) location of key-operated switch
(3) the steering column
(4) Power-assisted steering electric
motor
(5) Power-assisted steering com-
puter

36A-7
STEERING ASSEMBLY
Steering column: Removal - Refitting
LEFT-HAND DRIVE
36A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aUnlock the steering column.
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags - Pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aSet the wheels straight ahead.
aRemove:
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (MR 411, 88C, Airbags
- Pretensioners),
-the steering wheel (see 36A, Steering assembly,
Steering wheel: Removal - Refitting, page 36A-
23) ,-the steering column switch assembly (see Steer-
ing column switch assembly: Removal - Refit-
ting) (MR 411, 84A, Steering column switch
assembly),
-the immobiliser antenna/transponder ring (see
Transponder ring: Removal - Refitting) (MR
411, 82A, Immobiliser),
-the ignition switch if the steering column is replaced
(see Ignition switch: Removal - Refitting) (MR
411, 82A, Immobiliser).
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the cover from the universal joint (1) (do not
keep).
aRemove:
-the universal joint bolt (2) (do not keep),
-the universal joint nut (do not keep). Equipment required
Diagnostic tool
Tightening torquesm
bolt connecting the
steering column to the
inter mediate shaft30 Nm
steer ing column bolts21 Nm
universal joint bolt24 Nm
IMPORTANT
To avoid any risk of triggering when working on
or near a pyrotechnic component (airbags or pre-
tensioners), lock the airbag computer using the
diagnostic tool.
When this function is activated, all the trigger
lines are inhibited and the airbag warning light on
the instrument panel lights up continuously (igni-
tion on).
IMPORTANT
Never handle the pyrotechnic systems (preten-
sioners or airbags) near to a source of heat or
naked flame - they may be triggered.
119544

36A-8
STEERING ASSEMBLY
Steering column: Removal - Refitting
LEFT-HAND DRIVE
36A
aDisconnect the power-assisted steering computer
connectors (3) .
aRemove:
-the steering column bolts (4) ,
-the steering column with the intermediate shaft,
-the bolt connecting the steering column to the inter-
mediate shaft,-the steering column intermediate shaft.
aRemove:
-the steering column bolts (5) ,
-the steering column with the intermediate shaft,
REFITTING
I - REFITTING PREPARATIONS OPERATION
aAlways replace:
-the steering wheel bolt after each removal,
-the universal joint bolt and cam nut after each re-
moval. POWER ASSISTED STEERING
119858
119883
MANUAL STEERING
119647

36A-9
STEERING ASSEMBLY
Steering column: Removal - Refitting
LEFT-HAND DRIVE
36A
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the intermediate shaft to the steering column,
-the bolt connecting the steering column to the inter-
mediate shaft.
aTorque tighten the bolt connecting the steering
column to the intermediate shaft (30 Nm).
aRefit:
-the steering column with the intermediate shaft on
the cross member using the retainer (6) ,
-the bolts on the steering column.
aTorque tighten the steering column bolts (21 Nm).
aConnect the power-assisted steering computer con-
nectors.aObserve the direction of fitting for the universal joint
cam nut and bolt.
afit the universal joint to the steering box.
aRefit the universal joint cam nut and bolt.
aPosition the universal joint cam nut and bolt.
aImmobilise the cam nut in its housing (on the univer-
sal joint).
aPretighten the universal joint cam nut and bolt. POWER ASSISTED STEERING
119859
POWER ASSISTED STEERING
116021