light SATURN OUTLOOK 2009 Owners Manual

Page 343 of 432

Uniform Tire Quality
Grading
Quality grades can be found
where applicable on the tire
sidewall between tread shoulder
and maximum section width.
For example:
Treadwear 200 Traction AA
Temperature A
The following information relates
to the system developed by the
United States National Highway
Traffic Safety Administration
(NHTSA), which grades tires
by treadwear, traction, and
temperature performance.
This applies only to vehicles
sold in the United States.The grades are molded on the
sidewalls of most passenger car
tires. The Uniform Tire Quality
Grading (UTQG) system does
not apply to deep tread,
winter-type snow tires,
space-saver, or temporary use
spare tires, tires with nominal rim
diameters of 10 to 12 inches
(25 to 30 cm), or to some
limited-production tires.
While the tires available on
General Motors passenger cars
and light trucks may vary with
respect to these grades, they
must also conform to federal
safety requirements and
additional General Motors Tire
Performance Criteria (TPC)
standards.Treadwear
The treadwear grade is a
comparative rating based on the
wear rate of the tire when tested
under controlled conditions on
a specied government test
course. For example, a tire
graded 150 would wear one
and a half (1.5) times as well
on the government course as a
tire graded 100. The relative
performance of tires depends
upon the actual conditions of
their use, however, and may
depart signicantly from the norm
due to variations in driving habits,
service practices, and differences
in road characteristics and
climate.
Service and Appearance Care 5-57
ProCarManuals.com

Page 351 of 432

2. Unwrap the sealant/air hose (F)
and the power plug (H).
3. Place the kit on the ground.
Make sure the tire valve
stem is positioned close to the
ground so the hose will reach it.
4. Remove the valve stem cap from
the at tire by turning it
counterclockwise.
5. Attach the sealant/air hose (F)
onto the tire valve stem. Turn
it clockwise until it is tight.
6. Plug the power plug (H) into the
accessory power outlet in the
vehicle. Unplug all items
from other accessory power
outlets. SeeAccessory Power
Outlet(s) on page 3-17.
If the vehicle has an accessory
power outlet, do not use the
cigarette lighter.
If the vehicle only has a cigarette
lighter, use the cigarette lighter.
Do not pinch the power plug
cord in the door or window.7. Start the vehicle. The vehicle
must be running while using
the air compressor.
8. Turn the selector switch (A)
counterclockwise to the
Sealant + Air position.
9. Press the on/off (B) button to
turn the tire sealant and
compressor kit on.
The compressor will inject
sealant and air into the tire.
The pressure gage (C) will initially
show a high pressure while the
compressor pushes the sealant
into the tire. Once the sealant is
completely dispersed into the tire,
the pressure will quickly drop and
start to rise again as the tire
inates with air only.10. Inate the tire to the
recommended ination pressure
using the pressure gage (C).
The recommended ination
pressure can be found on the
Tire and Loading Information
label. SeeInflation - Tire
Pressure on page 5-45.
The pressure gage (C) may
read higher than the actual tire
pressure while the compressor
is on. Turn the compressor
off to get an accurate pressure
reading. The compressor
may be turned on/off until the
correct pressure is reached.
Service and Appearance Care 5-65
ProCarManuals.com

Page 354 of 432

Always do a safety check rst. See
If a Tire Goes Flat on page 5-61.
1. Remove the tire sealant and
compressor kit from its storage
location. SeeTire Sealant
and Compressor Kit Storage on
page 5-70.
2. Unwrap the air only hose (G)
and the power plug (H).
3. Place the kit on the ground.
Make sure the tire valve
stem is positioned close to the
ground so the hose will reach it.4. Remove the tire valve stem cap
from the at tire by turning it
counterclockwise.
5. Attach the air only hose (G) onto
the tire valve stem by turning it
clockwise until it is tight.
6. Plug the power plug (H) into the
accessory power outlet in the
vehicle. Unplug all items
from other accessory power
outlets. SeeAccessory Power
Outlet(s) on page 3-17.
If the vehicle has an accessory
power outlet, do not use the
cigarette lighter.
If the vehicle only has a cigarette
lighter, use the cigarette lighter.
Do not pinch the power plug
cord in the door or window.
7. Start the vehicle. The vehicle
must be running while using
the air compressor.8. Turn the selector switch (A)
clockwise to the Air Only position.
9. Press the on/off (B) button to turn
the compressor on.
The compressor will inate the
tire with air only.
10. Inate the tire to the
recommended ination pressure
using the pressure gage (C).
The recommended ination
pressure can be found on the
Tire and Loading Information
label. SeeInflation - Tire
Pressure on page 5-45.
The pressure gage (C) may
read higher than the actual tire
pressure while the compressor
is on. Turn the compressor
off to get an accurate reading.
The compressor may be
turned on/off until the correct
pressure is reached.
5-68 Service and Appearance Care
ProCarManuals.com

Page 370 of 432

Appearance Care
Interior Cleaning
The vehicle’s interior will continue
to look its best if it is cleaned often.
Although not always visible, dust
and dirt can accumulate on the
upholstery. Dirt can damage carpet,
fabric, leather, and plastic surfaces.
Regular vacuuming is recommended
to remove particles from the
upholstery. It is important to keep
the upholstery from becoming and
remaining heavily soiled. Soils
should be removed as quickly as
possible. The vehicle’s interior may
experience extremes of heat that
could cause stains to set rapidly.
Lighter colored interiors may
require more frequent cleaning.
Use care because newspapers and
garments that transfer color to home
furnishings may also transfer color to
the vehicle’s interior.When cleaning the vehicle’s
interior, only use cleaners specically
designed for the surfaces being
cleaned. Permanent damage may
result from using cleaners on
surfaces for which they were not
intended. Use glass cleaner only on
glass. Remove any accidental
over-spray from other surfaces
immediately. To prevent over-spray,
apply cleaner directly to the cleaning
cloth.
Notice:Using abrasive cleaners
when cleaning glass surfaces on
the vehicle, could scratch the
glass and/or cause damage to the
rear window defogger. When
cleaning the glass on the vehicle,
use only a soft cloth and glass
cleaner.Many cleaners contain solvents that
may become concentrated in the
vehicle’s breathing space. Before
using cleaners, read and adhere to
all safety instructions on the label.
While cleaning the vehicle’s interior,
maintain adequate ventilation by
opening the vehicle’s doors and
windows.
Dust may be removed from small
buttons and knobs using a small
brush with soft bristles.
Products that remove odors from the
vehicle’s upholstery and clean the
vehicle’s glass can be obtained from
your dealer/retailer.
5-84 Service and Appearance Care
ProCarManuals.com

Page 373 of 432

Weatherstrips
Silicone grease on weatherstrips will
make them last longer, seal better,
and not stick or squeak. Apply
silicone grease with a clean cloth.
During very cold, damp weather
frequent application may be required.
SeeRecommended Fluids and
Lubricants on page 6-12.
Washing Your Vehicle
The best way to preserve the
vehicle’s nish is to keep it clean by
washing it often.
Notice:Certain cleaners contain
chemicals that can damage the
emblems or nameplates on the
vehicle. Check the cleaning
product label. If it states that it
should not be used on plastic
parts, do not use it on the vehicle
or damage may occur and it would
not be covered by the warranty.Do not wash the vehicle in direct
sunlight. Use a car washing soap.
Do not use cleaning agents that are
petroleum based or that contain acid
or abrasives, as they can damage
the paint, metal or plastic on the
vehicle. Approved cleaning products
can be obtained from your dealer/
retailer. Follow all manufacturers’
directions regarding correct product
usage, necessary safety precautions
and appropriate disposal of any
vehicle care product.
Rinse the vehicle well, before
washing and after to remove all
cleaning agents completely. If they
are allowed to dry on the surface,
they could stain.
Dry the nish with a soft, clean
chamois or an all-cotton towel to
avoid surface scratches and
water spotting.High pressure car washes may
cause water to enter the vehicle.
Avoid using high pressure washes
closer than 12 inches (30 cm)
to the surface of the vehicle.
Use of power washers exceeding
1,200 psi (8 274 kPa) can result
in damage or removal of paint and
decals.
Cleaning Exterior
Lamps/Lenses
Use only lukewarm or cold water, a
soft cloth and a car washing soap to
clean exterior lamps and lenses.
Follow instructions underWashing
Your Vehicle on page 5-87.
Finish Care
Occasional waxing or mild polishing
of the vehicle by hand may be
necessary to remove residue from
the paint nish. Approved cleaning
products can be obtained from
your dealer/retailer.
Service and Appearance Care 5-87
ProCarManuals.com

Page 381 of 432

FusesUsage
A/C
CLUTCH Air Conditioning
Clutch
ABS MTR Antilock Braking
System (ABS) Motor
AFS Adaptive Forward
Lighting SystemFuses
Usage
AIRBAG Airbag System AUX
POWER Auxiliary Power
AUX VAC PUMP Auxiliary Vacuum
Pump
Fuses
Usage
AWD All-Wheel-Drive
System
BATT 1 Battery 1
BATT 2 Battery 2
BATT 3 Battery 3
ECM Engine Control
Module
ECM 1 Engine Control
Module 1
EMISSION 1 Emission 1
EMISSION 2 Emission 2 EVEN
COILS Even Injector Coils
FAN 1 Cooling Fan 1
FAN 2 Cooling Fan 2
FOG LAMP Fog Lamps
FSCM Fuel System Control
Module
HORN Horn
HTD WASH Heated Windshield
Washer Fluid
Service and Appearance Care 5-95
ProCarManuals.com

Page 392 of 432

(d)Inspect wiper blades for wear,
cracking, or contamination. Clean
the windshield and wiper blades,
if contaminated. Replace wiper
blades that are worn or damaged.
See Windshield Wiper Blade
Replacement on page 5-38 and
Windshield, Backglass, and Wiper
Blades on page 5-88 for more
information.
(e)Make sure the safety belt
reminder light and safety belt
assemblies are working properly.
Look for any other loose or damaged
safety belt system parts. If you see
anything that might keep a safety belt
system from doing its job, have it
repaired. Have any torn or frayed
safety belts replaced. Also see
Checking the Restraint Systems
on page 1-61.(f)Lubricate all key lock cylinders,
hood latch assemblies, secondary
latches, pivots, spring anchor
and release pawl, hood and door
hinges, rear folding seats, and
liftgate hinges. More frequent
lubrication may be required when
exposed to a corrosive environment.
Applying silicone grease on
weatherstrips with a clean cloth will
make them last longer, seal
better, and not stick or squeak.
(g)A fluid loss in any vehicle
system could indicate a problem.
Have the system inspected
and repaired and the fluid level
checked. Add fluid if needed.(h)Change automatic transmission
fluid if the vehicle is mainly driven
under one or more of these
conditions:
In heavy city traffic where the
outside temperature regularly
reaches 90°F (32°C) or higher.
In hilly or mountainous terrain.
When doing frequent trailer
towing.
Uses such as found in taxi, police,
or delivery service.
(i)Drain, flush, and refill cooling
system. This service can be
complex; you should have your
dealer/retailer perform this service.
See Engine Coolant on page 5-19 for
what to use. Inspect hoses. Clean
radiator, condenser, pressure cap,
and filler neck. Pressure test the
cooling system and pressure cap.
6-8 Maintenance Schedule
ProCarManuals.com

Page 418 of 432

Owner Publications
Information on how to obtain product
bulletins and as described below is
applicable only in the fty U.S. states
and the District of Columbia, and
only for cars and light trucks with
a Gross Vehicle Weight Rating
(GVWR) less than 10,000 pounds
(4 536 kg). Copies of individual
bulletins are also at your participating
Saturn retailer. You can ask to
see them.
In Canada, information relating to
product service bulletins can
be obtained by contacting your
Saturn retailer.
Service Bulletins
Saturn regularly sends its retailers
useful service bulletins about Saturn
products. Saturn monitors product
performance in the eld. We then
prepare bulletins for servicing
our products better. You can get
these bulletins, too.Bulletins cover various subjects.
Some pertain to the proper use and
care of your vehicle. Some describe
costly repairs. Others describe
inexpensive repairs which, if done on
time with the latest parts, may avoid
future costly repairs.
Some bulletins tell a technician how
to repair a new or unexpected
condition. Others describe a quicker
way to x your vehicle. They can
help a technician service your
vehicle better.
Most bulletins apply to conditions
affecting a small number of vehicles.
Your Saturn retailer or a qualied
technician may have to determine
if a specic bulletin applies to your
vehicle. To order Saturn bulletins,
call Saturn Publications at
1-800-2-SATURN or visit
saturn-publications.com to order
online.
Vehicle Data
Recording and
Privacy
Your Saturn vehicle has a number of
sophisticated computers that record
information about the vehicle’s
performance and how it is driven.
For example, your vehicle uses
computer modules to monitor and
control engine and transmission
performance, to monitor the
conditions for airbag deployment and
deploy airbags in a crash and, if so
equipped, to provide antilock braking
to help the driver control the vehicle.
These modules may store data to
help your dealer/retailer technician
service your vehicle. Some modules
may also store data about how you
operate the vehicle, such as rate of
fuel consumption or average speed.
These modules may also retain the
owner’s personal preferences, such
as radio pre-sets, seat positions, and
temperature settings.
7-16 Customer Assistance Information
ProCarManuals.com

Page 421 of 432

A
Accessories and
Modications...................... 5-3
Accessory Power.................2-21
Accessory Power Outlets......3-17
Adding Equipment to Your
Airbag-Equipped Vehicle....1-60
Additional Required Services,
Scheduled Maintenance....... 6-6
Additives, Fuel...................... 5-6
Add-On Electrical
Equipment.......................5-92
Air Cleaner/Filter, Engine.......5-17
Air Conditioning...................3-19
Airbag
Readiness Light................3-33
Airbag System.....................1-47
Adding Equipment to
Your Airbag-Equipped
Vehicle........................1-60
How Does an Airbag
Restrain?.....................1-53
Passenger Sensing
System........................1-55
Servicing Your
Airbag-Equipped
Vehicle........................1-60Airbag System (cont.)
What Makes an Airbag
Inate?........................1-52
What Will You See After
an Airbag Inates?........1-53
When Should an Airbag
Inate?........................1-51
Where Are the Airbags?.....1-49
Airbags
Passenger Status
Indicator.......................3-34
All-Wheel Drive....................5-35
All-Wheel-Drive (AWD)
System............................. 4-8
Antilock Brake System (ABS).... 4-4
Warning Light...................3-37
Appearance Care
Aluminum or
Chrome-Plated Wheels . . . 5-89
Care of Safety Belts..........5-86
Chemical Paint Spotting.....5-90
Cleaning Exterior
Lamps/Lenses...............5-87
Fabric/Carpet...................5-85
Finish Care......................
5-87
Finish Damage.................5-90
Instrument Panel, Vinyl, and
Other Plastic Surfaces....5-86Appearance Care (cont.)
Interior Cleaning...............5-84
Leather...........................5-86
Sheet Metal Damage........5-90
Tires...............................5-90
Underbody Maintenance....5-90
Washing Your Vehicle........5-87
Weatherstrips...................5-87
Windshield, Backglass,
and Wiper Blades..........5-88
Assistance Program,
Roadside.......................... 7-6
Audio System......................3-74
Audio Steering Wheel
Controls.....................3-125
Navigation/Radio System,
see Navigation
Manual.......................3-103
Setting the Clock..............3-74
Audio System(s)..................3-75
Audio Systems
Radio Reception.............3-126
Rear Seat (RSA).............3-123
Theft-Deterrent Feature....3-125
Automatic Transmission
Fluid...............................5-18
Operation........................2-24
INDEX i-1
ProCarManuals.com

Page 422 of 432

B
Battery...............................5-29
Electric Power
Management.................3-15
Run-Down Protection.........3-16
Belt Routing, Engine.............6-15
Bluetooth
®.........................3-103
Brake
Emergencies...................... 4-5
Brake Fluid.........................5-27
Brakes...............................5-27
Antilock............................. 4-4
Parking...........................2-27
System Warning Light.......3-36
Braking................................ 4-3
Braking in Emergencies.......... 4-5
Break-In, New Vehicle..........2-20
Bulb Replacement................5-37
Fog Lamp ........................3-13
Halogen Bulbs..................5-36
Headlamp Aiming..............5-35
Headlamps......................5-35
High Intensity Discharge
(HID) Lighting...............5-36Bulb Replacement (cont.)
License Plate Lamps.........5-37
Taillamps, Turn Signal,
Stoplamps and
Sidemarker Lamps.........5-36
Buying New Tires.................5-54
C
Calibration..........................3-54
California
Perchlorate Materials
Requirements................. 5-4
California Fuel....................... 5-6
California Proposition 65
Warning............................ 5-3
Camera, Rear Vision............2-37
Canadian Owners..................... ii
Capacities and
Specications...................5-98
Carbon Monoxide.................2-11
Engine Exhaust................2-30
Liftgate............................2-10
Winter Driving..................4-15
Care of
Safety Belts.....................5-86Cargo
Tie Downs .......................2-53
Cargo Cover........................2-53
Cargo Management System....2-53
CD, MP3 ....................3-92, 3-97
Center Console Storage........2-50
Chains, Tire........................5-60
Charging System Light..........3-35
Check
Engine Lamp...................3-39
Checking Things Under
the Hood .........................5-10
Chemical Paint Spotting........5-90
Child Restraints
Infants and Young
Children.......................1-30
Lower Anchors and
Tethers for Children.......1-37
Older Children..................1-28
Securing a Child Restraint
in a Rear Seat Position....1-43
Securing a Child Restraint
in the Right Front Seat
Position.......................1-45
Systems..........................1-33
Where to Put the
Restraint......................1-35
i-2 INDEX
ProCarManuals.com

Page:   < prev 1-10 ... 61-70 71-80 81-90 91-100 101-110 111-120 next >