light SATURN VUE HYBRID 2009 Owner's Guide

Instrument Panel
Brightness
This feature controls the brightness
of the instrument panel lights.
The thumbwheel for this feature is
located on the left side of the
steering wheel next to the exterior
lamps control.
Turn the thumbwheel to the right or
left to brighten or dim the lights.
Dome Lamp
*
(Dome Lamp Override):Press
this button to keep the dome
lamps and other interior lamps
turned off while any door is open.
Press this button again to return it to
the out position and the lamps
automatically come on when any
door is opened.
+(On/Off):Press this button to
turn the dome lamps on and off
while the doors are closed.
Entry Lighting
If the dome lamp override button is
in the out position, the lamps
inside the vehicle automatically
come on when any door is opened
or when the Remote Keyless
Entry (RKE) unlock button is
pressed. After the door is opened
the lights remain on and stay on for
20 seconds after the doors are
closed, or until the key is put into
the ignition and turned to theACC/ACCESSORY position. The
lights will then gradually dim until it
is no longer lit.
Reading Lamps
The reading lamps are located on
the overhead console.
To turn the reading lamps on or off,
press the button located next to
each lamp.
Electric Power
Management
The vehicle has Electric Power
Management (EPM) that estimates
the battery’s temperature and
state of charge. It then adjusts the
voltage for best performance
and extended life of the battery.
When the battery’s state of charge is
low, the voltage is raised slightly to
quickly bring the charge back up.
When the state of charge is high, the
voltage is lowered slightly to prevent
overcharging. If the vehicle has a
voltmeter gage or a voltage display
3-14 Instrument Panel
ProCarManuals.com

Automatic Operation
This climate control system
automatically maintains the desired
temperature inside the vehicle.
Do not cover the sensor located on
the top of the instrument panel
near the windshield or the sensor
grille below the climate control
faceplate. These two sensors help
regulate the inside air temperature.
AUTO (Automatic Fan):Turn
the fan knob to AUTO for the system
to automatically adjust the fan
speed to reach the desired inside
temperature.
Temperature Control:Select the
desired air temperature between
60-90°F (16-32°C). Typically,
the best setting is near 75°F (23°C).
Choosing the coldest or warmest
temperature setting does not cause
the system to heat or cool any
faster.AUTO (Automatic Air Delivery
Mode):Turn the air delivery mode
knob to AUTO for the system to
automatically control the direction of
the airow to help reach the
desired inside temperature.
The system automatically controls
the air inlet to supply the outside air
or recirculated inside air needed
to cool the vehicle faster. The
indicator light on the recirculation
button will be lit whenever the
system changes to recirculation.
Press the recirculation button
to change to outside air. However,
the recirculation mode may turn
back on automatically.
In cold weather, if the fan and air
delivery modes are in automatic, the
system starts at lower fan speeds
to avoid directing cold air into
the vehicle until warmer air is
available. The climate control
system directs air to the oor, but
may automatically change modes as
the vehicle warms up to maintain
the chosen temperature setting.The length of time needed to warm
the interior depends on the
outside temperature and inside
temperature of the vehicle.
Manual Operation
It is best to use the automatic
settings to maximize fuel economy.
A(Fan Control):Turn clockwise
or counterclockwise to increase
or decrease the fan speed. To turn
the fan off, turn the left knob to
the
9position. In any setting other
than off, the fan runs continuously
with the ignition on. The fan must be
turned on to run the air conditioning
compressor. There will be some
airow noticeable from the various
outlets when driving, even with
the fan in the off position. This is to
ensure some fresh air is always
available in the vehicle. To turn off
the air completely, turn the fan
to
9and select the recirculation
button.
3-18 Instrument Panel
ProCarManuals.com

#(Normal Air Conditioning):
Press to turn the air conditioning
system on or off. An indicator
light comes on to show that the air
conditioning is on. Normal Air
Conditioning (A/C) can be selected
in any mode as long as the fan
is on and the outside air temperature
is above freezing. Normal A/C
cannot be selected at the same time
as Hybrid Air Conditioning (A/C).
A ashing indicator light indicates
that the air conditioning compressor
is currently not available.
When Normal A/C is selected, the
climate control system prevents
all automatic engine start/stop
operations. This will ensure the
cabin comfort is maintained.
See “Air Conditioning and Automatic
Engine Start/Stop” later in this
section.
N(Hybrid Air Conditioning):
Press to turn the Hybrid A/C system
on or off. An indicator light comes
on to show that Hybrid A/C is
on. Hybrid A/C can be selected inany mode, except defrost as long as
the fan is on and the outside air
temperature is above freezing.
Hybrid A/C cannot be selected at
the same time as the normal
air conditioning. A ashing indicator
light shows the air conditioning
compressor is not available.
The Hybrid A/C works to balance
fuel economy and air conditioning
comfort. When Hybrid A/C is used in
warm weather, the vehicle gets
better fuel economy by allowing
more frequent start/stops. For
additional cooling, select Normal
A/C. See “Air Conditioning and
Automatic Engine Start/Stop” later in
this section.
@(Recirculation):Press to
toggle between the recirculation and
outside air modes. The indicator
light turns on when the recirculation
mode is selected. This mode can
be used to prevent outside air
and odors from entering the vehicle
or to help cool the air inside the
vehicle more quickly. Avoid usingthe recirculation mode during high
periods of humidity and cool outside
temperatures since this may
result in increased window fogging.
If window fogging is experienced,
select the defrost mode.
Recirculation mode is not available
in oor, defog or defrost modes.
If the button is selected in
these modes, the indicator will ash.
This helps prevent window fogging
and moisture building up inside
the vehicle.
Rear Window Defogger
The rear window defogger uses a
warming grid to remove fog from the
rear window.
The rear window defogger will only
work when the ignition is in
ON/RUN.
<(Rear Window Defogger):
Press to turn the rear window
defogger on or off. An indicator light
on the button comes on to show
that it is activated.
3-20 Instrument Panel
ProCarManuals.com

Outlet Adjustment
Use the louvers located on the air
outlets to change the direction of the
airow.
Operation Tips
Clear away any ice, snow, or
leaves from the air inlets at
the base of the vehicle that may
block the ow of air into the
vehicle.
Do not use any non-GM
approved hood deectors that
could adversely affect the
performance of the system.
Keep the path under the front
seats clear of objects to help
circulate the air inside of
the vehicle more effectively.
Warning Lights,
Gages, and Indicators
Warning lights and gages can
signal that something is wrong
before it becomes serious enough
to cause an expensive repair or
replacement. Paying attention to the
warning lights and gages could
prevent injury.
Warning lights come on when there
may be or is a problem with one
of the vehicle’s functions. Some
warning lights come on briey when
the engine is started to indicate
they are working.Gages can indicate when there may
be or is a problem with one of the
vehicle’s functions. Often gages and
warning lights work together to
indicate a problem with the vehicle.
When one of the warning lights
comes on and stays on while
driving, or when one of the gages
shows there may be a problem,
check the section that explains what
to do. Follow this manual’s advice.
Waiting to do repairs can be
costly and even dangerous.
3-22 Instrument Panel
ProCarManuals.com

Speedometer and
Odometer
The speedometer shows the
vehicle’s speed in both miles
per hour (mph) and kilometers
per hour (km/h).
The odometer shows how far the
vehicle has been driven, in
either miles or kilometers.
If the vehicle needs a new odometer
installed, the new one is set to
the mileage total of the old
odometer. If it cannot, it will be set
at zero and a label must be put
on the driver’s door to show the old
mileage reading when the new
odometer was installed. If the
mileage is unknown, the label
should then indicate that the
previous mileage is unknown.
Trip Odometer
The trip odometer is located on the
instrument panel and shows how
far the vehicle has been driven since
the trip odometer was last reset.
To reset the trip odometer to zero,
press and hold the trip/reset
button on the speedometer for
about two seconds. Press the
trip/reset button to switch between
the trip odometer and odometer.
Tachometer
The tachometer displays the
engine speed in revolutions
per minute (rpm).The auto stop indicator is located at
the bottom of the tachometer. For
more information seeAuto Stop
Mode on page 3-35.
Safety Belt Reminders
Driver Safety Belt Reminder
Light
When the engine is started, a chime
sounds for several seconds to
remind the driver to fasten their
safety belt, unless it is already
buckled.
The safety belt light comes on and
stays on for several seconds,
then ashes for several more.
This chime and light are repeated if
the driver safety belt remains
unbuckled and the vehicle is in
motion. If the driver safety belt is
already buckled, neither the
chime nor the light comes on. U.S. shown, Canada similar
3-24 Instrument Panel
ProCarManuals.com

Passenger Safety Belt
Reminder Light
Several seconds after the engine
is started, a chime sounds for
several seconds to remind the front
passenger to buckle their safety belt.
This only occurs if the passenger
airbag is enabled. SeePassenger
Sensing System on page 1-49for
more information. The passenger
safety belt light, located on the
instrument panel, comes on and
stays on for several seconds and
then ashes for several more.
This chime and light are repeated if
the passenger remains unbuckled
and the vehicle is in motion.
If the passenger safety belt is
buckled before the engine is started,
neither the chime nor the light
comes on.The front passenger safety belt
warning light and chime may turn on
if an object is put on the seat
such as a briefcase, handbag,
grocery bag, laptop or other
electronic device. To turn off the
warning light and or chime, remove
the object from the seat or buckle
the safety belt.
Airbag Readiness Light
There is an airbag readiness light on
the instrument panel cluster,
which shows the airbag symbol. The
system checks the airbag’s
electrical system for malfunctions.
The light indicates if there is an
electrical problem. The system
check includes the airbag sensor,
the pretensioners, the airbag
modules, the wiring and the crash
sensing and diagnostic module.
For more information on the airbag
system, seeAirbag System on
page 1-41.
{CAUTION
If the airbag readiness light stays
on after the vehicle is started or
comes on while driving, it means
the airbag system might not be
working properly. The airbags in
the vehicle might not inate in a
crash, or they could even inate
without a crash. To help avoid
injury, have the vehicle serviced
right away.
The airbag readiness light comes on
when the vehicle is started, and
ashes for a few seconds. The light
goes out when the system is ready.
Instrument Panel 3-25
ProCarManuals.com

If the airbag readiness light stays on
after the vehicle is started or
comes on while driving, the airbag
system may not work properly. Have
the vehicle serviced right away.
The airbag readiness light should
ash for a few seconds when
the engine is started. If the light
does not come on then, have it xed
immediately. If there is a problem
with the airbag system, an
airbag Driver Information Center
(DIC) message may also come on.
SeeDIC Warnings and Messages
on page 3-42for more information.Passenger Airbag Status
Indicator
The vehicle has the passenger
sensing system. SeePassenger
Sensing System on page 1-49
for important safety information. The
instrument panel has a passenger
airbag status indicator.
When the vehicle is started, the
passenger airbag status indicator
will light ON and OFF, or the symbol
for on and off, for several seconds
as a system check. Then, after
several more seconds, the status
indicator will light either ON or OFF,or either the on or off symbol to let
you know the status of the right
front passenger frontal and
seat-mounted side impact airbags.
If the word ON or the on symbol
is lit on the passenger airbag status
indicator, it means that the right
front passenger frontal airbag and
seat-mounted side impact airbag are
enabled (may inate).
If the word OFF or the off symbol is
lit on the airbag status indicator,
it means that the passenger sensing
system has turned off the right
front passenger frontal airbag and
seat-mounted side impact airbag.
If, after several seconds, both status
indicator lights remain on, or if
there are no lights at all, there may
be a problem with the lights or
the passenger sensing system. See
your dealer/retailer for service. United States
Canada
3-26 Instrument Panel
ProCarManuals.com

{CAUTION
If the airbag readiness light ever
comes on and stays on, it means
that something may be wrong with
the airbag system. To help avoid
injury to yourself or others, have
the vehicle serviced right away.
SeeAirbag Readiness Light on
page 3-25for more information,
including important safety
information.
Charging System Light
The charging system light comes on
briey when the ignition is turned
on, but the engine is not running, as
a check to show the light is
working. It should go out when the
engine is started.If the light stays on, or comes on
while driving, there could be a
problem with the electrical charging
system. Have it checked by your
dealer/retailer. Driving while this light
is on could drain the battery.
If a short distance must be driven
with the light on, be sure to turn off
all accessories, such as the
radio and air conditioner.
Brake System Warning
Light
The brake indicator light should
come on briey as the engine
is started. If it does not come on
have the vehicle serviced by
your dealer/retailer.
When the ignition is on, the brake
system warning light comes on
when the parking brake is set. Thelight stays on if the parking brake
does not fully release. If it stays on
after the parking brake is fully
released, there is a brake problem.
Have the brake system inspected
immediately.
{CAUTION
The brake system might not be
working properly if the brake
system warning light is on. Driving
with the brake system warning
light on can lead to a crash. If the
light is still on after the vehicle
has been pulled off the road and
carefully stopped, have the
vehicle towed for service.
If the light comes on while driving, a
chime sounds. Pull off the road and
stop. The pedal might be harder to
push or go closer to the oor. It might
also take longer to stop. If the light is
still on, have the vehicle towed for
service. SeeTowing Your Vehicle on
page 4-22.
United StatesCanada
Instrument Panel 3-27
ProCarManuals.com

Antilock Brake System
(ABS) Warning Light
For vehicles with the Antilock Brake
System (ABS), this light should
come on briey as the engine
is started. If it does not come on
have the vehicle serviced by
your dealer/retailer.
If the ABS light stays on longer than
a few seconds after engine is
started, or comes on and stays on
while driving, try resetting the
system. To reset the system:
1. While driving, pull over when it is
safe to do so.
2. Place the vehicle in P (PARK).
3. Turn off the ignition.
4. Then restart the engine.If the ABS light remains on after
resetting the system or comes
on again while driving, the vehicle
needs service. If the ABS light is on,
but the regular brake system
warning light is not on, the antilock
brakes are not working properly,
but the regular brakes are still
functioning. Have the vehicle
serviced right away. If both brake
lights are on, the vehicle does
not have antilock brakes, and there
is a problem with the regular
brakes as well. Have the vehicle
towed for service. SeeTowing Your
Vehicle on page 4-22.
StabiliTrak®/Traction
Control System (TCS)
Warning Light
The Traction Control System
(TCS)/StabiliTrak®system warning
light comes on briey as the
engine is started.
If it does not, have the vehicle
serviced by your dealer/retailer. If
the system is working normally
the indicator lights go off.
This light ashes while the Traction
Control System (TCS) and/or the
StabiliTrak system are working.
It also ashes when the Antilock
Brake System (ABS) is activated.
If the light comes on and stays
on while driving there is a problem
with the Traction Control System
(TCS) or the StabiliTrak system. The
3-28 Instrument Panel
ProCarManuals.com

TCS and/or StabiliTrak system
automatically turns off and vehicle
needs service.
When this light is on, the TCS
system does not limit wheel spin
and/or the StabiliTrak system does
not assist with vehicle control.
When the Traction Control system
and/or StabiliTrak system are turned
off, the light comes on.
When the Traction Control System
and/or StabiliTrak system are
turned on, the light turns off.
SeeTraction Control System (TCS)
on page 4-8andStabiliTrak
®
System on page 4-7for more
information.
Engine Coolant
Temperature Warning
Light
The engine coolant temperature
light should come on briey as the
engine is started. If it does not
come on have the vehicle serviced
by your dealer/retailer.
Notice:Driving with the engine
coolant temperature warning light
on could cause the vehicle to
overheat. SeeEngine Overheating
on page 5-23. The vehicle’s
engine could be damaged, and it
might not be covered by the
vehicle warranty. Never drive with
the engine coolant temperature
warning light on.If this light comes on and stays on,
the engine has overheated. Pull
over and seeEngine Overheating on
page 5-23for more information.Tire Pressure Light
If the vehicle has a tire pressure
monitoring system, the tire pressure
light should come on briey as
the engine is started. If it does not,
have the vehicle serviced by
your dealer/retailer. It provides
information about tire pressures and
the Tire Pressure Monitoring
System.
When the Light is On Steady
This indicates that one or more of
the tires are signicantly
underinated.
A tire pressure message in the
Driver Information Center (DIC), can
accompany the light. SeeDIC
Instrument Panel 3-29
ProCarManuals.com