Seat Cordoba 2005 Owner's Manual

129 Refuelling
Safety FirstControls and equipment Tips and Maintenance Technical Data
Properties of RME
•RME is chemically produced from vegetable oil (predominantly
rapeseed oil) in a process whereby the oil is mixed with methanol
and converted, via a catalyst, into RME.
•RME is almost totally sulfur free. The combustion of RME thus
emits practically no sulfur dioxide (SO
2).
•Exhaust gas contains less
– carbon monoxide
– hydrocarbons
– particles (i.e. soot)
than with conventional diesel fuel.
All emission values are lower than legal requirements.
•RME fuel is biodegradable.
•Performance may be slightly lower.
•Fuel consumption may be slightly higher.
•RME can be used in temperatures down to approximately –10 °C.
•Diesel fuel must be added at ambient temperatures of less than
–10 °C to prevent deterioration to the biodiesel. The mixing ratio
of diesel to biodiesel must be approximately 50:50.
I If
f tth
he
e RRM
ME
E rra
at
ti
io
o eex
xc
ce
ee
ed
ds
s 550
0%
%,
, tto
oo
o mmu
uc
ch
h ssm
mo
ok
ke
e mma
ay
y bbe
e ffo
or
rm
me
ed
d.
.
•During the summer months, RME may be mixed with diesel at
any ratio.
K
Driving in winter
When using summer Diesel trouble may be experienced at
temperatures below
0 °C because the fuel thickens due to wax separation.
For this reason winter Diesel which is more resistant to cold is sold
during the winter in some countries, and this works correctly down
to between –15 °C and –22 °C approximately, depending on the
brand of fuel used.
The biodiesel available in countries with different climactic
conditions usually has different temperature characteristics.
Technical Service Centres or service stations in each country can
inform you of the specific characteristics of the respective diesel.
K
Filter preheating
The vehicle is fitted with a filter preheater. This will ensure that the
fuel system will remain operational down to about –25 °C,
provided that winter Diesel which is cold resistant down to –15 °C
is used.
If, at temperatures below –25 °C the fuel is waxed to such an
extent that the engine will not start it is sufficient to place the
vehicle in a warm enclosure for a while.
Fuela ad
dd
di
it
ti
iv
ve
es
s
(anti-waxing agent), petroland similar fluids must
n no
ot
t
be mixed with Diesel fuel.
K

130Intelligent technology
I
In
nt
te
el
ll
li
ig
ge
en
nt
t tte
ec
ch
hn
no
ol
lo
og
gy
y
B
Br
ra
ak
ke
es
s
General notes
• Brake lining wear depends to a large extent on the operating
conditions and style of driving. On vehicles which are used mainly
in town traffic and stop/ start conditions or are driven hard it may
be necessary to have the thickness of the brake linings checked by
a Technical Service Centre in between the intervals given in the
Inspection and Service Schedule.
• Change down in good time when driving downhill, in order to
make use of the engine braking effect. This relieves strain on the
brake system. When the brakes are applied do not keep them on
continuously, apply and release alternately.
K
What can have a negative effect on the brakes?
W We
et
t oor
r ggr
ri
it
tt
te
ed
d rro
oa
ad
d ssu
ur
rf
fa
ac
ce
eO Ov
ve
er
rh
he
ea
at
ti
in
ng
g oof
f tth
he
e bbr
ra
ak
ke
es
s
•U
Un
nd
de
er
r cce
er
rt
ta
ai
in
n cco
on
nd
di
it
ti
io
on
ns
s ee.
.g
g.
. aaf
ft
te
er
r ddr
ri
iv
vi
in
ng
g tth
hr
ro
ou
ug
gh
h wwa
at
te
er
r,
, hhe
ea
av
vy
y rra
ai
in
n ffa
al
ll
ls
s
o or
r aaf
ft
te
er
r tth
he
e vve
eh
hi
ic
cl
le
e hha
as
s bbe
ee
en
n wwa
as
sh
he
ed
d,
, tth
he
e bbr
ra
ak
ke
es
s cco
ou
ul
ld
d sse
et
t iin
n lla
at
te
er
r tth
ha
an
n
n no
or
rm
ma
al
l ddu
ue
e tto
o dda
am
mp
p,
, oor
r iin
n wwi
in
nt
te
er
r –– ffr
ro
oz
ze
en
n,
, bbr
ra
ak
ke
e ddi
is
sc
cs
s aan
nd
d lli
in
ni
in
ng
gs
s –– tth
he
e
b br
ra
ak
ke
es
s mmu
us
st
t ffi
ir
rs
st
t bbe
e ddr
ri
ie
ed
d tth
hr
ro
ou
ug
gh
h cca
ar
re
ef
fu
ul
l bbr
ra
ak
ki
in
ng
g.
.
W
WA
AR
RN
NI
IN
NG
G
•F Fu
ul
ll
l bbr
ra
ak
ki
in
ng
g ppo
ow
we
er
r mmi
ig
gh
ht
t aal
ls
so
o sse
et
t iin
n lla
at
te
er
r tth
ha
an
n nno
or
rm
ma
al
l eev
ve
en
n wwh
he
en
n ddr
ri
iv
vi
in
ng
g
o on
n ggr
ri
it
tt
te
ed
d rro
oa
ad
ds
s iif
f yyo
ou
u hha
av
ve
e nno
ot
t bbr
ra
ak
ke
ed
d ffo
or
r sso
om
me
e tti
im
me
e –– tth
he
e lla
ay
ye
er
r oof
f ssa
al
lt
t oon
n
t th
he
e bbr
ra
ak
ke
e ddi
is
sk
ks
s aan
nd
d bbr
ra
ak
ke
e lli
in
ni
in
ng
gs
s mmu
us
st
t ffi
ir
rs
st
t bbe
e wwo
or
rn
n ddo
ow
wn
n wwh
hi
il
ls
st
t bbr
ra
ak
ki
in
ng
g.
.
W
WA
AR
RN
NI
IN
NG
G ((c
co
on
nt
ti
in
nu
ue
ed
d)
)
• • NNe
ev
ve
er
r lle
et
t tth
he
e bbr
ra
ak
ke
es
s ““r
ru
ub
b”
” bby
y ppr
re
es
ss
si
in
ng
g tth
he
e ppe
ed
da
al
l tto
oo
o lli
ig
gh
ht
tl
ly
y wwh
he
en
n yyo
ou
u ddo
o
n no
ot
t rre
ea
al
ll
ly
y nne
ee
ed
d tto
o bbr
ra
ak
ke
e.
. TTh
hi
is
s cca
au
us
se
es
s tth
he
e bbr
ra
ak
ke
es
s tto
o oov
ve
er
rh
he
ea
at
t,
, lle
ea
ad
ds
s tto
o
l lo
on
ng
ge
er
r bbr
ra
ak
ki
in
ng
g ddi
is
st
ta
an
nc
ce
es
s aan
nd
d tto
o aa hhi
ig
gh
he
er
r lle
ev
ve
el
l oof
f wwe
ea
ar
r.
.
• • BBe
ef
fo
or
re
e sst
ta
ar
rt
ti
in
ng
g oon
n aa llo
on
ng
g sst
tr
re
et
tc
ch
h oof
f rro
oa
ad
d iin
n aa vve
er
ry
y hhi
il
ll
ly
y aar
re
ea
a,
, ppl
le
ea
as
se
e rre
ed
du
uc
ce
e
y yo
ou
ur
r ssp
pe
ee
ed
d,
, cch
ha
an
ng
ge
e tto
o aa llo
ow
we
er
r gge
ea
ar
r ((m
ma
an
nu
ua
al
l gge
ea
ar
rb
bo
ox
x)
) oor
r cch
ho
oo
os
se
e aa llo
ow
we
er
r
p po
os
si
it
ti
io
on
n ((a
au
ut
to
om
ma
at
ti
ic
c gge
ea
ar
rb
bo
ox
x)
).
. IIn
n tth
hi
is
s wwa
ay
y yyo
ou
u wwi
il
ll
l uus
se
e tth
he
e bbr
ra
ak
ki
in
ng
g ppo
ow
we
er
r oof
f
t th
he
e een
ng
gi
in
ne
e aan
nd
d rre
el
li
ie
ev
ve
e ppr
re
es
ss
su
ur
re
e oon
n tth
he
e bbr
ra
ak
ke
es
s.
.
• • IIf
f aa ffr
ro
on
nt
t ssp
po
oi
il
le
er
r,
, ffu
ul
ll
l ssi
iz
ze
e wwh
he
ee
el
l ttr
ri
im
ms
s eet
tc
c.
.,
, iis
s rre
et
tr
ro
of
fi
it
tt
te
ed
d,
, iit
t iis
s nne
ec
ce
es
ss
sa
ar
ry
y tto
o
e en
ns
su
ur
re
e tth
ha
at
t tth
he
e ffl
lo
ow
w oof
f aai
ir
r tto
o tth
he
e ffr
ro
on
nt
t bbr
ra
ak
ke
es
s iis
s nno
ot
t rre
es
st
tr
ri
ic
ct
te
ed
d –– oot
th
he
er
rw
wi
is
se
e
t th
he
e bbr
ra
ak
ke
es
s cca
an
n oov
ve
er
rh
he
ea
at
t.
.
K
W WA
AR
RN
NI
IN
NG
G

131 Intelligent technology
Safety FirstControls and equipment Tips and Maintenance Technical Data
Servobrake
A
An
nt
ti
i-
-l
lo
oc
ck
k bbr
ra
ak
ke
e ssy
ys
st
te
em
m aan
nd
d ttr
ra
ac
ct
ti
io
on
n cco
on
nt
tr
ro
ol
l
A AB
BS
S
Anti-lock brake system (ABS)
The anti-lock brake system prevents the wheels locking during
braking.
The anti-lock brake system (ABS) is an important part of the
vehicle’s active safety system.
H Ho
ow
w tth
he
e AAB
BS
S wwo
or
rk
ks
s
If one of the wheels is turning too slowly in relation to the road
speed, and is close to locking, the system will reduce the braking
pressure for this wheel. The driver is made aware of this control
process by a p pu
ul
ls
sa
at
ti
in
ng
g oof
f tth
he
e bbr
ra
ak
ke
e ppe
ed
da
al
l
and audible noise.This is a deliberate warning to the driver that one or more of the
wheels is tending to lock and the ABS control function has
intervened. In this situation it is important to keep the brake pedal
fully depressed so the ABS can regulate the brake application. Do
not pump the brake pedal.
If you brake hard on a slippery road surface, the best possible
control is retained as the wheels do not lock.
However, ABS will not necessarily guarantee shorter braking
distances in all conditions. The braking distance could even be
longer if you brake on gravel or on fresh snow covering a slippery
surface.
The traction control system (TCS)*
This system includesA AB
BS
Sand T
TC
CS
S.
The traction control system prevents the drive wheels from
spinning when the car is accelerating.
T Th
he
e sse
er
rv
vo
o iis
s oop
pe
er
ra
at
te
ed
d bby
y aa vva
ac
cu
uu
um
m wwh
hi
ic
ch
h iis
s oon
nl
ly
y gge
en
ne
er
ra
at
te
ed
d wwh
he
en
n tth
he
e
e en
ng
gi
in
ne
e iis
s rru
un
nn
ni
in
ng
g.
. FFo
or
r tth
hi
is
s rre
ea
as
so
on
n tth
he
e vve
eh
hi
ic
cl
le
e ssh
ho
ou
ul
ld
d nno
ot
t bbe
e aal
ll
lo
ow
we
ed
d tto
o rro
ol
ll
l
w wi
it
th
h tth
he
e een
ng
gi
in
ne
e ssw
wi
it
tc
ch
he
ed
d oof
ff
f.
.
W Wh
he
en
n tth
he
e bbr
ra
ak
ke
e sse
er
rv
vo
o iis
s nno
ot
t wwo
or
rk
ki
in
ng
g bbe
ec
ca
au
us
se
e,
, ffo
or
r eex
xa
am
mp
pl
le
e,
, tth
he
e vve
eh
hi
ic
cl
le
e iis
s
b be
ei
in
ng
g tto
ow
we
ed
d oor
r aa dde
ef
fe
ec
ct
t hha
as
s ooc
cc
cu
ur
rr
re
ed
d oon
n tth
he
e bbr
ra
ak
ke
e sse
er
rv
vo
o iit
ts
se
el
lf
f,
, tth
he
e bbr
ra
ak
ke
e
p pe
ed
da
al
l mmu
us
st
t bbe
e ppr
re
es
ss
se
ed
d cco
on
ns
si
id
de
er
ra
ab
bl
ly
y hha
ar
rd
de
er
r tto
o cco
om
mp
pe
en
ns
sa
at
te
e ffo
or
r tth
he
e aab
bs
se
en
nc
ce
e
o of
f sse
er
rv
vo
o aas
ss
si
is
st
ta
an
nc
ce
e.
.
K
W WA
AR
RN
NI
IN
NG
G
• • TTh
he
e aan
nt
ti
i-
-l
lo
oc
ck
k bbr
ra
ak
ke
e ssy
ys
st
te
em
m cca
an
nn
no
ot
t dde
ef
fy
y tth
he
e lla
aw
ws
s oof
f pph
hy
ys
si
ic
cs
s.
. SSl
li
ip
pp
pe
er
ry
y aan
nd
d
w we
et
t rro
oa
ad
ds
s aar
re
e dda
an
ng
ge
er
ro
ou
us
s eev
ve
en
n wwi
it
th
h AAB
BS
S!
! IIf
f yyo
ou
u nno
ot
ti
ic
ce
e tth
ha
at
t tth
he
e AAB
BS
S iis
s
w wo
or
rk
ki
in
ng
g ((t
to
o cco
ou
un
nt
te
er
ra
ac
ct
t llo
oc
ck
ke
ed
d wwh
he
ee
el
ls
s uun
nd
de
er
r bbr
ra
ak
ki
in
ng
g)
),
, yyo
ou
u ssh
ho
ou
ul
ld
d rre
ed
du
uc
ce
e
s sp
pe
ee
ed
d iim
mm
me
ed
di
ia
at
te
el
ly
y tto
o ssu
ui
it
t tth
he
e rro
oa
ad
d aan
nd
d ttr
ra
af
ff
fi
ic
c cco
on
nd
di
it
ti
io
on
ns
s.
. DDo
o nno
ot
t lle
et
t tth
he
e
e ex
xt
tr
ra
a ssa
af
fe
et
ty
y ffe
ea
at
tu
ur
re
es
s tte
em
mp
pt
t yyo
ou
u iin
nt
to
o tta
ak
ki
in
ng
g aan
ny
y rri
is
sk
ks
s wwh
he
en
n ddr
ri
iv
vi
in
ng
g.
.
• • TTh
he
e eef
ff
fe
ec
ct
ti
iv
ve
en
ne
es
ss
s oof
f AAB
BS
S iis
s aal
ls
so
o dde
et
te
er
rm
mi
in
ne
ed
d bby
y tth
he
e tty
yr
re
es
s ffi
it
tt
te
ed
d.
.
• • IIf
f tth
he
e rru
un
nn
ni
in
ng
g gge
ea
ar
r oor
r bbr
ra
ak
ke
es
s aar
re
e mmo
od
di
if
fi
ie
ed
d,
, tth
he
e eef
ff
fe
ec
ct
ti
iv
ve
en
ne
es
ss
s oof
f tth
he
e AAB
BS
S
c co
ou
ul
ld
d bbe
e sse
ev
ve
er
re
el
ly
y lli
im
mi
it
te
ed
d.
.
K
W WA
AR
RN
NI
IN
NG
G


132Intelligent technology
D
De
es
sc
cr
ri
ip
pt
ti
io
on
n aan
nd
d oop
pe
er
ra
at
ti
io
on
n oof
f tth
he
e ttr
ra
ac
ct
ti
io
on
n cco
on
nt
tr
ro
ol
l ssy
ys
st
te
em
m ddu
ur
ri
in
ng
g
a ac
cc
ce
el
le
er
ra
at
ti
io
on
n ((T
TC
CS
S)
)
TCS reduces engine power to help prevent the drive wheels of front-
wheel drive vehicles losing traction during acceleration. The system
works in the entire speed range in conjunction with ABS. If a
malfunction should occur in the ABS, the TCS will also be out of
action.
TCS helps the vehicle to start moving, accelerate and climb a
gradient in slippery conditions where this may otherwise be
difficult or even impossible.
The TCS is switched on automatically when the engine is started. If
necessary, it may be turned on or off by briefly pushing the button
on the centre console.
When the TCS is off, the warning lamp is lit.
The TCS should normally be left switched on at all times. Only in
exceptional circumstances, when slipping of the wheels is
required, should it be disconnected, for example:
– With compact temporary spare wheel.
– When using the snow chains
– When driving in deep snow or on loose surfaces
– When the vehicle is bogged-down, to free it by rocking it.
The TCS should be switched on again afterwards as soon as
possible.N No
ot
te
e• In order to ensure that TCS function correctly, all four wheels must be
fitted with the same tyres. Any differences in the rolling radiusof the tyres
can cause the system to reduce engine power when this is not desired.
• Modifications to the vehicle (e.g. to the engine, the brake system, running
gear or any components affecting the wheels and tyres) could affect the
efficiency of the ABS and TCS.
K
E El
le
ec
ct
tr
ro
on
ni
ic
c sst
ta
ab
bi
il
li
is
sa
at
ti
io
on
n ppr
ro
og
gr
ra
am
mm
me
e ((E
ES
SP
P)
)*
*
General notes
The electronic stabilisation program increases the vehicle’s
stability on the road.
The electronic stabilisation program helps to reduce the danger of
skidding. It includes the A AB
BS
S
, E ED
DL
L
and T TC
CS
S
systems.
H Ho
ow
w EES
SP
P wwo
or
rk
ks
s
ESP reduces the danger of skidding by braking the wheels
individually.
The system uses the steering wheel angle and road speed to
calculate the changes of direction desired by the driver, and
• • IIt
t mmu
us
st
t bbe
e rre
em
me
em
mb
be
er
re
ed
d tth
ha
at
t TTC
CS
S cca
an
nn
no
ot
t dde
ef
fy
y tth
he
e lla
aw
ws
s oof
f pph
hy
ys
si
ic
cs
s.
. TTh
hi
is
s
s sh
ho
ou
ul
ld
d bbe
e kke
ep
pt
t iin
n mmi
in
nd
d,
, ppa
ar
rt
ti
ic
cu
ul
la
ar
rl
ly
y oon
n ssl
li
ip
pp
pe
er
ry
y aan
nd
d wwe
et
t rro
oa
ad
ds
s aan
nd
d wwh
he
en
n
t to
ow
wi
in
ng
g aa ttr
ra
ai
il
le
er
r.
.
W
WA
AR
RN
NI
IN
NG
G
• • AAl
lw
wa
ay
ys
s aad
da
ap
pt
t yyo
ou
ur
r ddr
ri
iv
vi
in
ng
g sst
ty
yl
le
e tto
o ssu
ui
it
t tth
he
e cco
on
nd
di
it
ti
io
on
n oof
f tth
he
e rro
oa
ad
ds
s aan
nd
d tth
he
e
t tr
ra
af
ff
fi
ic
c ssi
it
tu
ua
at
ti
io
on
n.
. DDo
o nno
ot
t lle
et
t tth
he
e eex
xt
tr
ra
a ssa
af
fe
et
ty
y aaf
ff
fo
or
rd
de
ed
d bby
y TTC
CS
S tte
em
mp
pt
t yyo
ou
u iin
nt
to
o
t ta
ak
ki
in
ng
g aan
ny
y rri
is
sk
ks
s wwh
he
en
n ddr
ri
iv
vi
in
ng
g,
, tth
hi
is
s cca
an
n cca
au
us
se
e aac
cc
ci
id
de
en
nt
ts
s.
.
W
WA
AR
RN
NI
IN
NG
G ((c
co
on
nt
ti
in
nu
ue
ed
d)
)


133 Intelligent technology
Safety FirstControls and equipment Tips and Maintenance Technical Data
constantly compares them with the actual behaviour of the vehicle.
If the desired course is not being maintained (for instance, if the
car is starting to skid), then the ESP compensates automatically by
braking the appropriate wheel.
The forces acting on the braked wheel bring the vehicle back to a
stable condition. If the vehicle tends to oversteer, the system will
act on the front wheel on the outside of the turn.
N No
ot
te
e
•In order to ensure that ESP functions correctly, all four wheels must be
fitted with the same tyres. Any differences in the rolling radiusof the tyres
can cause the system to reduce engine power when this is not desired.
•Modifications to the vehicle (e.g. to the engine, the brake system, running
gear or any components affecting the wheels and tyres) could affectthe
efficiency of the ABS, EDL, ESP and TCS.
K
Anti-lock brake system (ABS)
The anti-lock brake system prevents the wheels locking during
braking
⇒chapter “Anti-lock brake system and traction control
ABS”.
K
Electronic differential lock (EDL)
The electronic differential lock helps prevent the loss of traction
caused if one of the driven wheels starts spinning.
EDL helps the vehicle to start moving, accelerate and climb a
gradient in slippery conditions where this may otherwise be
difficult or even impossible.
It uses the ABS sensors to monitor the speed of the driven wheels.
In case of an EDL fault the warning light for ABS lights up
⇒
chapter “Warning lamps”.
At speeds of up to approximately 80 km/h, it is able to balance out
differences in the speed of the driven wheels of approximately 100
rpm caused by a slippery road surface on one side of the vehicle. It
does this by braking the wheel which has lost traction and
distributing more driving force to the other driven wheel via the
differential.
To prevent the disc brake of the braked wheel from overheating,
the EDL cuts out automatically if subjected to excessive loads. The
vehicle will continue to function normally without EDL. For this
reason, the driver is not informed that the EDL has been switched
off.
The EDL will switch on again automatically when the brake has
cooled down.
• • IIt
t mmu
us
st
t bbe
e rre
em
me
em
mb
be
er
re
ed
d tth
ha
at
t TTC
CS
S cca
an
nn
no
ot
t dde
ef
fy
y tth
he
e lla
aw
ws
s oof
f pph
hy
ys
si
ic
cs
s.
. TTh
hi
is
s
s sh
ho
ou
ul
ld
d bbe
e kke
ep
pt
t iin
n mmi
in
nd
d,
, ppa
ar
rt
ti
ic
cu
ul
la
ar
rl
ly
y oon
n ssl
li
ip
pp
pe
er
ry
y aan
nd
d wwe
et
t rro
oa
ad
ds
s aan
nd
d wwh
he
en
n
t to
ow
wi
in
ng
g aa ttr
ra
ai
il
le
er
r.
.
• • AAl
lw
wa
ay
ys
s aad
da
ap
pt
t yyo
ou
ur
r ddr
ri
iv
vi
in
ng
g sst
ty
yl
le
e tto
o ssu
ui
it
t tth
he
e cco
on
nd
di
it
ti
io
on
n oof
f tth
he
e rro
oa
ad
ds
s aan
nd
d tth
he
e
t tr
ra
af
ff
fi
ic
c ssi
it
tu
ua
at
ti
io
on
n.
. DDo
o nno
ot
t lle
et
t tth
he
e eex
xt
tr
ra
a ssa
af
fe
et
ty
y aaf
ff
fo
or
rd
de
ed
d bby
y EES
SP
P tte
em
mp
pt
t yyo
ou
u iin
nt
to
o
t ta
ak
ki
in
ng
g aan
ny
y rri
is
sk
ks
s wwh
he
en
n ddr
ri
iv
vi
in
ng
g,
, tth
hi
is
s cca
an
n cca
au
us
se
e aac
cc
ci
id
de
en
nt
ts
s.
.
W
WA
AR
RN
NI
IN
NG
G


134Intelligent technology
N
No
ot
te
e
•Modifications to the vehicle (e.g. to the engine, the brake system, running
gear or any components affecting the wheels and tyres) could affect the
efficiency of the EDL.
K
The traction control system (TCS)
The traction control system prevents the drive wheels from
spinning when the car is accelerating
⇒chapter “Anti-lock brake
system and traction control ABS”.
K
P Po
ow
we
er
r sst
te
ee
er
ri
in
ng
g*
*
Do not keep the steering wheel fully turned more than 15 seconds
when the engine is switched on, as the hydraulic oil will be heated
to a high temperature by the servo pump.
T Th
hi
is
s cco
ou
ul
ld
d dda
am
ma
ag
ge
e tth
he
e ppo
ow
we
er
r sst
te
ee
er
ri
in
ng
g ssy
ys
st
te
em
m.
.
Furthermore, each time you turn the steering wheel as far as it will
go with the engine off, you will hear a series of noises made by the
excessive effort of the servo pump. Another consequence is the
decrease of the idling speed for a short period of time.
N No
ot
te
e
Some functional aspects of the vehicle can be programmed according to
the client’s driving style. For further information, consult the Technical
Service.
K
• • WWh
he
en
n aac
cc
ce
el
le
er
ra
at
ti
in
ng
g oon
n aa ssl
li
ip
pp
pe
er
ry
y ssu
ur
rf
fa
ac
ce
e,
, ffo
or
r eex
xa
am
mp
pl
le
e oon
n iic
ce
e aan
nd
d ssn
no
ow
w,
,
p pr
re
es
ss
s tth
he
e aac
cc
ce
el
le
er
ra
at
to
or
r cca
ar
re
ef
fu
ul
ll
ly
y.
. DDe
es
sp
pi
it
te
e EED
DL
L,
, tth
he
e ddr
ri
iv
ve
en
n wwh
he
ee
el
ls
s mma
ay
y sst
ta
ar
rt
t tto
o
s sp
pi
in
n.
. TTh
hi
is
s cco
ou
ul
ld
d iim
mp
pa
ai
ir
r tth
he
e vve
eh
hi
ic
cl
le
e’
’s
s sst
ta
ab
bi
il
li
it
ty
y.
.
• • AAl
lw
wa
ay
ys
s aad
da
ap
pt
t yyo
ou
ur
r ddr
ri
iv
vi
in
ng
g sst
ty
yl
le
e tto
o ssu
ui
it
t tth
he
e cco
on
nd
di
it
ti
io
on
n oof
f tth
he
e rro
oa
ad
ds
s aan
nd
d tth
he
e
t tr
ra
af
ff
fi
ic
c ssi
it
tu
ua
at
ti
io
on
n.
. DDo
o nno
ot
t lle
et
t tth
he
e eex
xt
tr
ra
a ssa
af
fe
et
ty
y aaf
ff
fo
or
rd
de
ed
d bby
y EED
DL
L tte
em
mp
pt
t yyo
ou
u iin
nt
to
o
t ta
ak
ki
in
ng
g aan
ny
y rri
is
sk
ks
s wwh
he
en
n ddr
ri
iv
vi
in
ng
g,
, tth
hi
is
s cca
an
n cca
au
us
se
e aac
cc
ci
id
de
en
nt
ts
s.
.
W
WA
AR
RN
NI
IN
NG
G

135 Your vehicle and the environment
Safety FirstControls and equipment Tips and Maintenance Technical Data
Y
Yo
ou
ur
r vve
eh
hi
ic
cl
le
e aan
nd
d tth
he
e een
nv
vi
ir
ro
on
nm
me
en
nt
t
T
Th
he
e ffi
ir
rs
st
t 11,
,5
50
00
0 kkm
m –– aan
nd
d aaf
ft
te
er
rw
wa
ar
rd
ds
s
Running-in
During the first few operating hours the engine internal friction is
higher than later on when all the moving parts have bedded down.
How well this running-in process is done depends to a
considerable extent on the way the vehicle is driven during the first
1,500 km.
K
Up to 1,000 kilometres
the following general rules apply:
•D Do
o nno
ot
t uus
se
e ffu
ul
ll
l tth
hr
ro
ot
tt
tl
le
e
•D Do
o nno
ot
t ddr
ri
iv
ve
e ffa
as
st
te
er
r tth
ha
an
n 33/
/4
4 oof
f tto
op
p ssp
pe
ee
ed
d
•A Av
vo
oi
id
d hhi
ig
gh
h een
ng
gi
in
ne
e ssp
pe
ee
ed
ds
s
•Trailer towing should if possible be avoided.
From 1,000 – 1,500 km
The speed can be gradually increased to the road or engine
maximum.
K
During and after the running-in period the following
applies:
•Do not overrev the engine when cold – either in neutral or in the
gears.
All speeds and revs given are only valid when engine isp pr
ro
op
pe
er
rl
ly
y
w wa
ar
rm
m
.
F Fo
or
r tth
he
e ssa
ak
ke
e oof
f tth
he
e een
nv
vi
ir
ro
on
nm
me
en
nt
t
Do not drive with the engine speed unnecessarily high – changing up
early helps to save fuel, reduces noise and protects the environment⇒"Environment friendly and economical driving" chapter.
•Do not let engine labour – change down when engine no longer
runs smoothly.
K
• • NNe
ew
w tty
yr
re
es
s mmu
us
st
t aal
ls
so
o bbe
e ““r
ru
un
n iin
n”
” bbe
ec
ca
au
us
se
e tth
he
ey
y ddo
o nno
ot
t hha
av
ve
e mma
ax
xi
im
mu
um
m
a ad
dh
he
es
si
io
on
n aat
t tth
he
e sst
ta
ar
rt
t.
. TTh
hi
is
s mmu
us
st
t bbe
e tta
ak
ke
en
n iin
nt
to
o aac
cc
co
ou
un
nt
t bby
y ddr
ri
iv
vi
in
ng
g cca
ar
re
ef
fu
ul
ll
ly
y
d du
ur
ri
in
ng
g tth
he
e ffi
ir
rs
st
t 110
00
0 kkm
m.
.
• • NNe
ew
w bbr
ra
ak
ke
e lli
in
ni
in
ng
gs
s mmu
us
st
t aal
ls
so
o bbe
e rru
un
n iin
n aan
nd
d ddo
o nno
ot
t hha
av
ve
e tth
he
e oop
pt
ti
im
mu
um
m
f fr
ri
ic
ct
ti
io
on
n ppr
ro
op
pe
er
rt
ti
ie
es
s ddu
ur
ri
in
ng
g tth
he
e ffi
ir
rs
st
t 220
00
0 kkm
m.
. TTh
he
e ssl
li
ig
gh
ht
tl
ly
y rre
ed
du
uc
ce
ed
d bbr
ra
ak
ki
in
ng
g
W
WA
AR
RN
NI
IN
NG
G
e ef
ff
fe
ec
ct
t cca
an
n bbe
e cco
om
mp
pe
en
ns
sa
at
te
ed
d ffo
or
r bby
y mmo
or
re
e ppr
re
es
ss
su
ur
re
e oon
n tth
he
e bbr
ra
ak
ke
e ppe
ed
da
al
l.
. TTh
hi
is
s
a al
ls
so
o aap
pp
pl
li
ie
es
s wwh
he
en
n nne
ew
w lli
in
ni
in
ng
gs
s hha
av
ve
e bbe
ee
en
n ffi
it
tt
te
ed
d.
.
K
W WA
AR
RN
NI
IN
NG
G ((c
co
on
nt
ti
in
nu
ue
ed
d)
)

136Your vehicle and the environment
After the running-in period
•On vehicles with a rev counter* the maximum permissible engine
speed is shown by the beginning of the red zone on the rev
counter scale. The needle of the counter must not move into this
zone.
Extremely high engine revs will be automatically governed.
K
C Cl
le
ea
an
ni
in
ng
g tth
he
e eex
xh
ha
au
us
st
t ffu
um
me
es
s
Description
T
Th
he
e ppe
er
rf
fe
ec
ct
t ffu
un
nc
ct
ti
io
on
ni
in
ng
g oof
f tth
he
e ccl
le
ea
an
ni
in
ng
g ssy
ys
st
te
em
m ffo
or
r eex
xh
ha
au
us
st
t ffu
um
me
es
s
is of great importance for the environment-friendly functioning of
your vehicle.
Therefore, keep in mind the following points:
•Versions with a catalytic converter must only use unleaded fuel
⇒"Filling the tank" chapter.
•In vehicles with a catalytic converter never drive until the fuel
tank is completely empty. Irregular fuel supply can cause misfiring,
thus allowing unburned fuel into the exhaust system which can
cause overheating and damage to the catalyst.
•If you experience starting difficulties, loss of power or engine
problems while driving, the cause could be a failure in the ignition.
In this case, fuel may be entering the exhaust system withoutburning and, in this way being released into the atmosphere.
Furthermore, the catalyst could deteriorate due to overheating.
Reduce speed immediately. Have this problem fixed at the nearest
Technical Service Centre.
•Do not overload the engine with oil
⇒"Engine oil" chapter.
•Do not towstartthe vehicle for more than 50 m
⇒"Tow
start/towing" chapter.
N No
ot
te
e
Even when the cleaning system for exhaust fumes is in perfect working
order, under certain circumstances, the fumes may smell like sulfur.
This depends on the percentage of sulfur in the fuel.
Often it is sufficient to change brands or buy super unleaded.
K
•D Du
ue
e tto
o ppo
os
ss
si
ib
bl
le
e hhi
ig
gh
h tte
em
mp
pe
er
ra
at
tu
ur
re
es
s oof
f tth
he
e cca
at
ta
al
ly
ys
st
t,
, ddo
o nno
ot
t ppa
ar
rk
k iin
n
p pl
la
ac
ce
es
s wwh
he
er
re
e tth
he
e cca
at
ta
al
ly
ys
st
t iis
s eea
as
si
il
ly
y eex
xp
po
os
se
ed
d tto
o iin
nf
fl
la
am
mm
ma
ab
bl
le
e mma
at
te
er
ri
ia
al
l.
.
•D
Do
o nno
ot
t uus
se
e aad
dd
di
it
ti
io
on
na
al
l ppr
ro
ot
te
ec
ct
ti
io
on
n ffo
or
r tth
he
e bbo
od
dy
y oor
r aan
nt
ti
ic
co
or
rr
ro
os
si
iv
ve
e ppr
ro
od
du
uc
ct
ts
s ffo
or
r
s su
um
mp
ps
s aan
nd
d eex
xh
ha
au
us
st
t ppi
ip
pe
es
s,
, c
ca
at
ta
al
ly
yt
ti
ic
c cco
on
nv
ve
er
rt
te
er
rs
s oor
r hhe
ea
at
t ssh
hi
ie
el
ld
ds
s.
.T
Th
he
e
a ab
bo
ov
ve
e mme
en
nt
ti
io
on
ne
ed
d mma
at
te
er
ri
ia
al
l cco
ou
ul
ld
d iig
gn
ni
it
te
e wwh
hi
il
le
e ddr
ri
iv
vi
in
ng
g.
.
W
WA
AR
RN
NI
IN
NG
G

137 Your vehicle and the environment
Safety FirstControls and equipment Tips and Maintenance Technical Data
E
En
nv
vi
ir
ro
on
nm
me
en
nt
t-
-f
fr
ri
ie
en
nd
dl
ly
y aan
nd
d eec
co
on
no
om
mi
ic
ca
al
l
d dr
ri
iv
vi
in
ng
g
General notes
Three factors determine the fuel consumption, the burden on the
environment and the wear on the engine, brakes and tyres:
•The personal driving style.
•The individual conditions of the use of the car.
•Technical prerequisites.
The fuel consumption can be reduced by 10 to 15 percent by
adopting a thoughtful and economic driving style. This chapter will
help you lower pollution and save money by following 10
suggestions.
K
Suggestion 1. Thoughtful driving style
The highest fuel consumption takes place during acceleration. If
you drive in a thoughtful manner you will have to brake less and,
therefore, accelerate less. You can also let the vehicle roll, i.e.
when you can foresee that the following traffic light will be red.
K
Suggestion 2. Changing gears saves energy
Another way to save fuel is to change up as quickly as possible. If
you drive with high engine revs the car will use up more energy.
The fig. 100shows the relation between the consumption (l/100
km) and speed (km/h) in first, second, third, fourth and fifth gear.
The following rules may be helpful. Never drive more than a few
meters in first gear. When you reach 2,000 revolutions, you should
change up.
If you drive a vehicle with an automatic gearbox, press the
accelerator pedal gently. Do not press it to the kick-down position.
This way, a consumption oriented program is automatically
selected. It changes up as soon as possible and takes longer to
change down.
K
30 50 70km/h
90
l/100km
1.
2.
3.
4.
5.
B45-354PFig. 100

138Your vehicle and the environment
Suggestion 3. Avoid driving at maximum speed
Try not to drive at maximum speed. The increase of fuel
consumption, exhaust pollution and noise is disproportionate at
high speeds.
The illustration shows the relation between consumption (l/100
km) and speed (km/h)
⇒fig. 101.
If only about 3 quarters of top speed is utilized, the fuel
consumption will be reduced by about half.
Suggestion 4. Decrease idling
It is worth switching off1)the engine in traffic jams, at railroad
crossings and at traffic lights with a long red light. The savings in
fuel after 30-40 seconds with the engine switched off is higher
than the fuel used to switch the engine on again.
K
Suggestion 5. Periodic revisions
Your fuel savings are guaranteed even before going on a trip with
periodic revisions by your Technical Service Centre. Proper engine
maintenance is not only a safety and maintenance issue but also a
fuel consumption issue.
Poor fine tuning of the engine may increase fuel consumption by
up to 10%.
Check the oil level every time you fill up. The oil consumption
depends largely on the engine load. Depending on the driving
style, the oil consumption can be up to 1.0 l/1000 km.
Another suggestion: You can also lower oil consumption by using
synthetic oils.
K
km/h
max
l/100km
B45-355PFig. 101
1)Statutory regulations must be respected.
D Dr
ri
iv
vi
in
ng
g aat
t hhi
ig
gh
h ssp
pe
ee
ed
ds
s dde
ec
cr
re
ea
as
se
es
s rro
oa
ad
d ssa
af
fe
et
ty
y.
.
K
W WA
AR
RN
NI
IN
NG
G