Seat Cordoba 2005 Owner's Manual

139 Your vehicle and the environment
Safety FirstControls and equipment Tips and Maintenance Technical Data
Suggestion 6. Avoid short drives
The engine and the catalytic converter must reach its optimum
functioning temperature in order to effectively reduce consumption
and toxic gas emissions.
The fuel consumption of a cold engine of a normal vehicle right
after the start is about 30-40 liters per 100 km. After about one
kilometer the consumption decreases to 20 liters. After about
f fo
ou
ur
r
kilometers the engine has warmed up and the consumption is
normal. For this reason, it is important to avoid short drives and
heating the vehicle’s engine when the vehicle is not moving. Drive
on quickly!
The ambient temperature also counts. The illustration shows the
difference in consumption (l/100km) for the same distance (km) at
+20°C and –10°C. Your vehicle’s consumption is higher in the
summer than in the winter
⇒fig. 102.K
Suggestion 7. Check the tyre pressure
Make sure that the tyres have always adequate pressure. Even half
a bar less increases the level of fuel consumption by 5 percent. If
the pressure is not correct, the tyres wear out faster due to an
excessive deformation and overheating which, in turn, will
decrease the driving performance.
Always check the tyre pressure when the tyre is cold.
In addition, do not drive year round with winter tyres. They make
more noise and increase fuel consumption by 10 percent. Change
to summer tyres on time.
K
Suggestion 8. Avoid unnecessary weight
Apart from driving habits and periodic revisions of your vehicle,
there are other ways to reduce fuel consumption:
A Av
vo
oi
id
d uun
nn
ne
ec
ce
es
ss
sa
ar
ry
y wwe
ei
ig
gh
ht
t
Every kilogram increases fuel consumption. For this reason, it is
worth checking your boot to avoid unnecessary weight.
Frequently, the roof rack will stay on the roof even though it is no
longer needed. Due to greater air resistance, an unloaded roof
rack at a speed of 100-120 km/h increases the consumption by
approx. 12%.
K
5+20°C –10°C
15 25km
30
l/100km
B45-356PFig. 102

140Your vehicle and the environment
Suggestion 9. Save electricity
The alternator generates electricity while driving. The more
electricity is used, the higher the fuel consumption.
The heated rear window, extra lights, the heater fan and air
conditioning* use a large amount of energy. The heated rear
window creates a consumption of approx. one liter for every 10
hours.
For this reason, disconnect electrical consumers as soon as they
are no longer needed. The alternator generates electricity when the
engine is running.
K
Suggestion 10. Written check-up
If you wish to reduce fuel consumption keep a trip book. It is not
much work and is worth while since it allows you to detect possible
consumption variations (positive or negative) on time and
intervene, if necessary. If you detect an increase in consumption
you should examine the driving conditions since the last filling.
K
T Tr
ra
ai
il
le
er
r tto
ow
wi
in
ng
g
What do you need to bear in mind when towing a trailer?
The vehicle is designed mainly to carry people and luggage.
However it may also be used to tow a trailer, as long as you fit it
with the technically appropriate equipment and you do not
exceed the maximum authorised weights
⇒“Technical Data”
chapter.Towing a trailer not only demands more from the car, but from the
driver too.
You should therefore strictly adhere to the service and running-in
instructions on the following pages.
T Te
ec
ch
hn
ni
ic
ca
al
l rre
eq
qu
ui
ir
re
em
me
en
nt
ts
s
•If the trailer to be towed has a 7-pin plug, an adapter cable can
be used which may be obtained in any Technical Service Centre.
Installation of a towing bracket at a later stage should be carried
out according to the instructions of the towing bracket
manufacturer.
I If
f aa ttr
ra
ai
il
le
er
r iis
s ffi
it
tt
te
ed
d aat
t aa lla
at
te
er
r sst
ta
ag
ge
e,
, yyo
ou
u ssh
ho
ou
ul
ld
d uus
se
e tth
he
e bbo
od
dy
y rre
ei
in
nf
fo
or
rc
ce
em
me
en
nt
t
s se
et
t dde
es
si
ig
gn
ne
ed
d bby
y SSE
EA
AT
T.
.
O Ot
th
he
er
rw
wi
is
se
e yyo
ou
u mma
ay
y sse
er
ri
io
ou
us
sl
ly
y dda
am
ma
ag
ge
e tth
he
e bbo
od
dy
y wwo
or
rk
k.
.
D Da
an
ng
ge
er
r oof
f aac
cc
ci
id
de
en
nt
t!
!
T To
o iin
ns
st
ta
al
ll
l tth
he
e tto
ow
w jjo
oi
in
nt
t,
, wwe
e rre
ec
co
om
mm
me
en
nd
d tth
ha
at
t yyo
ou
u vvi
is
si
it
t aa TTe
ec
ch
hn
ni
ic
ca
al
l SSe
er
rv
vi
ic
ce
e
C Ce
en
nt
tr
re
e.
.
K
W WA
AR
RN
NI
IN
NG
G

141 Your vehicle and the environment
Safety FirstControls and equipment Tips and Maintenance Technical Data
Fixing points for tow bar*A4 attachment points
B72 mm
C420 (empty vehicle) /
350 mm (vehicle with max. load)
D958 mm
E413 mm
F166 mm K
Driving tips
• • TTh
he
e tto
ow
wi
in
ng
g dde
ev
vi
ic
ce
e iis
s aa ssa
af
fe
et
ty
y eel
le
em
me
en
nt
t aan
nd
d yyo
ou
u ssh
ho
ou
ul
ld
d tth
he
er
re
ef
fo
or
re
e
o on
nl
ly
y uus
se
e aa dde
ev
vi
ic
ce
e ssp
pe
ec
ci
if
fi
ic
ca
al
ll
ly
y dde
es
si
ig
gn
ne
ed
d ffo
or
r yyo
ou
ur
r vve
eh
hi
ic
cl
le
e aan
nd
d wwh
hi
ic
ch
h
i is
s ddu
ul
ly
y aap
pp
pr
ro
ov
ve
ed
d.
.
O Op
pe
er
ra
at
ti
io
on
ns
s iin
ns
st
tr
ru
uc
ct
ti
io
on
ns
s
•The removable ball coupling of the towing bracket* may be
stored in the tool box located inside the spare wheel recess.
•Additional mirrors are required if the traffic behind the trailer is
not visible with the exterior mirrors fitted as standard. Both exterior
mirrors must be attached to brackets in such a way that a sufficient
field of vision to the rear is guaranteed at all times.
•The permitted trailer weight must not be exceeded under any
circumstances
⇒chapter “Technical Data”.
•In vehicles equipped with air conditioning, the factory
installation provides reinforced cooling system to account for the
fitting of a towing device.
Fig. 103

AB
C
F
A
E
D
CON-006

142Your vehicle and the environment
•In vehicles without air conditioning, the cooling system should
be reinforced if a towing device is fitted at a later stage.
Failure to do so will submit the engine to greater stress (steep
slopes, high temperatures, heavy towing loads, etc.) and result in
overheating of the engine. For more information, contact a
Technical Service Centre.
•When using a trailer on mountain routes you must bear in mind
that the tow loads given in the “Technical data” chapter are only
applicable for slopes of 10% to 12%. If you do not use the full tow
load you may drive up steeper slopes.
•The given trailer weights are only applicable for altitudes up
to 1000 m above sea level. As the engine output drops due to
the decreasing air density, the climbing ability must also be
reduced by 10% for each further 1000 m.
•Where possible make full use of the maximum permissible
drawbar weight on the ball of the towing bracket but do not exceed
it
⇒chapter “Technical Data”.
•While observing the permissible trailer and drawbar weight,
distribute the load in the trailer so that heavy objects are as near
as possible to the axle. The objects must also be secured so that
they cannot slip about.
•The tyre pressures on the towing vehicle must be adjusted for full
load conditions, and also check the pressures on the trailer.
•Headlight settings should be checked, with the trailer attached,
before beginning the journey and adjusted as necessary.
On vehicles with headlight beam control it is only necessary to turn
the knurled disc on the dash board in the appropriate direction.D Dr
ri
iv
vi
in
ng
g iin
ns
st
tr
ru
uc
ct
ti
io
on
ns
s
To obtain the best possible handling of vehicle and trailer, the
following should be noted:
• Try to avoid driving with an unladen vehicle and a loaded trailer.
If this cannot be avoided, only drive slowly to allow for the
unfavourable weight distribution.
• As driving stability of vehicle and trailer decreaseswhen the
speed increases do not drive at the maximum permissible top
speed in unfavourable road, weather or wind conditions –
particularly when going downhill.
In any case the speed must be reduced as soon as the trailer
shows the slightest sign of snaking. On no account try to stop the
snaking by accelerating.
• • FFo
or
r ssa
af
fe
et
ty
y rre
ea
as
so
on
ns
s oon
ne
e ssh
ho
ou
ul
ld
d nno
ot
t ddr
ri
iv
ve
e ffa
as
st
te
er
r tth
ha
an
n 880
0 kkm
m/
/h
h
( (5
50
0 mmp
ph
h)
).
. TTh
hi
is
s aal
ls
so
o aap
pp
pl
li
ie
es
s iin
n cco
ou
un
nt
tr
ri
ie
es
s wwh
he
er
re
e hhi
ig
gh
he
er
r ssp
pe
ee
ed
ds
s aar
re
e
p pe
er
rm
mi
it
tt
te
ed
d.
.
• Always brake in good time. If the trailer has an overrun brake,
apply the brakes gently at first then firmly. This will avoid the
jerking caused by the trailer wheels locking.
Change down before going down a steep hill so that the engine
can act as a brake.
• When a long climb in a low gear with extremely high engine revs
must be negotiated at exceptionally high ambient temperatures
the coolant temperature gauge must be observed. When the gauge
needle moves to the right end of the scale, the road speed must be
reduced immediately.
• The cooling effect of the radiator fan cannot be increased by
changing down, because the speed of the fan is not dependent on


143 Your vehicle and the environment
Safety FirstControls and equipment Tips and Maintenance Technical Data
the engine speed. One should therefore not change down even
when towing a trailer as long as the engine can cope without the
vehicle speed dropping too much.
K
General notes
• • DDu
ur
ri
in
ng
g tth
he
e rru
un
nn
ni
in
ng
g iin
n ppe
er
ri
io
od
d yyo
ou
u ssh
ho
ou
ul
ld
d aav
vo
oi
id
d tto
ow
wi
in
ng
g aa ttr
ra
ai
il
le
er
r iif
f
p po
os
ss
si
ib
bl
le
e.
.
• • IIt
t iis
s aad
dv
vi
is
sa
ab
bl
le
e tto
o hha
av
ve
e tth
he
e vve
eh
hi
ic
cl
le
e sse
er
rv
vi
ic
ce
ed
d bbe
et
tw
we
ee
en
n tth
he
e
I In
ns
sp
pe
ec
ct
ti
io
on
n iin
nt
te
er
rv
va
al
ls
s iif
f iit
t iis
s uus
se
ed
d ffr
re
eq
qu
ue
en
nt
tl
ly
y ffo
or
r tto
ow
wi
in
ng
g aa ttr
ra
ai
il
le
er
r.
.
• The trailer and drawbar load figures on the data plate of the
towing bracket are for test certification only. The correct figuresfor
the vehicle, which may be lower than the above figures, are given
in the vehicle documents and in this manual.
• When using the towing device the car’s empty weight is reduced,
and as a result its effective load is decreased.
• Observe all statutory requirements regarding the use of a
trailer.
K
D Dr
ri
iv
vi
in
ng
g aab
br
ro
oa
ad
d
Observations
If the vehicle is to be taken abroad, the following must also be
borne in mind:
• If the vehicle has a petrol engine and catalytic converter, one
must ensure that unleaded petrol will be available during the
journey
⇒"Filling the tank" chapter. The automobile clubs offer
information about the unleaded filling station network.
•In some countries it is possible that a vehicle model is sold under
conditions where some spare parts are not available or that the
Technical Services may only carry out limited repairs.
SEAT importers and distributors will gladly provide information
about the technical preparation of your vehicle in addition to
necessary maintenance and repair possibilities.
K
Cover headlights
When the vehicle is used in a country which drives on the opposite
side of the road to the home country, the asymmetric dipped
headlights will dazzle oncoming traffic.
To prevent this, the areas of the headlight lenses shown in the
illustration must be covered with an opaque adhesive strip.
When using a sharp object (i.e. a razor blade) to cut the tape, do
not do this directly on the headlights as you may scratch them.


144Your vehicle and the environment
Cover for bi-focal headlights for driving on the left
On the right headlamp if you change from driving on the right to
the left hand side
⇒ fig. 104.
On the left headlamp if you change from driving on the right to the
left hand side
⇒ fig. 105. K
W
Wh
he
en
n yyo
ou
u ddr
ri
iv
ve
e oon
n tth
he
e oop
pp
po
os
si
it
te
e ssi
id
de
e oof
f tth
he
e rro
oa
ad
d tto
o yyo
ou
ur
r oow
wn
n cco
ou
un
nt
tr
ry
y aan
nd
d
w wi
it
th
h tth
he
e cco
or
rr
re
es
sp
po
on
nd
di
in
ng
g cco
ov
ve
er
ra
ag
ge
e oof
f tth
he
e hhe
ea
ad
dl
li
ig
gh
ht
ts
s,
, bbe
ea
ar
r iin
n mmi
in
nd
d tth
ha
at
t
v vi
is
si
ib
bi
il
li
it
ty
y iis
s rre
ed
du
uc
ce
ed
d aan
nd
d yyo
ou
u wwi
il
ll
l hha
av
ve
e tto
o aad
da
ap
pt
t yyo
ou
ur
r ddr
ri
iv
vi
in
ng
g sst
ty
yl
le
e aan
nd
d ssp
pe
ee
ed
d
a ac
cc
co
or
rd
di
in
ng
gl
ly
y ffo
or
r ssa
af
fe
et
ty
y rre
ea
as
so
on
ns
s.
.
K
W WA
AR
RN
NI
IN
NG
G
225225
2020
50
75mm
IBN-114
EP)EP)
“N“N
)N
9)mm
IBN-113Fig. 104
Fig. 105

145 Your vehicle and the environment
Safety FirstControls and equipment Tips and Maintenance Technical Data
Cover for bi-focal headlights for driving on the right
On the right headlamp if you change from driving on the left to the
right hand side
⇒ fig. 106.On the left headlamp if you change from driving on the left to the
right hand side
⇒ fig. 107.K
Cover for conventional headlights for driving on the left
220220
2020
55
70mm
IBN-115
EP)EP)
“N“N
))
PNmm
IBN-116
Fig. 106
Fig. 107
Fig. 108
Fig. 109()N()N
9N
)) “N (N•)
mm
IBN-118
•)•)
9N
)) “N (N•)
mm
IBN-117


146Your vehicle and the environment
On the right headlamp if you change from driving on the right to
the left hand side
⇒ fig. 108.
On the left headlamp if you change from driving on the right to the
left hand side
⇒ fig. 109.K
Cover for conventional headlights for driving on the right
On the right headlamp if you change from driving on the left to the
right hand side
⇒ fig. 110.
On the left headlamp if you change from driving on the left to the
right hand side
⇒ fig. 111.K
8080
2020
55
70mm
IBN-120
EPNEPN
ENEN
))
PNmm
IBN-119Fig. 110
Fig. 111

147 Your vehicle and the environment
Safety FirstControls and equipment Tips and Maintenance Technical Data
Cover for GDL headlights for driving on the left
On the right headlamp if you change from driving on the right to
the left hand side
⇒ fig. 112.On the left headlamp if you change from driving on the right to the
left hand side
⇒ fig. 113.K
Cover for GDL headlights for driving on the right
Fig. 112
Fig. 114
Fig. 115
Fig. 113
127127
2020
40
36mm
2626
IBN-128
UEUE
““““
“•
“•mm
IBN-127
E(N E(N
““
“9mm
“”“””E”E
IBN-125
U9U9
“)
““mm
“N“N
IBN-126

148Your vehicle and the environment
On the right headlamp if you change from driving on the left to the
right hand side
⇒ fig. 114.
On the left headlamp if you change from driving on the left to the
right hand side
⇒ fig. 115.K