SKODA OCTAVIA 2009 2.G / (1Z) Owner's Manual

Communication
150
Example for storing in the phone voice phonebook You can interrupt the dialogue at any time
by pressing the PTT button or with the
voice command
CANCEL
.
Select name– Press the PTT button. – Give the command
DIAL/SELECT NAMES/NAME
after the signal
tone.
After giving this command, there is the possibility to select a stored entry out of the phone voice phonebook.
Example for selecting an entry ou
t of the phone voice phonebook
You can interrupt the dialogue
at any time by pressing
the PTT button or with the
voice command
CANCEL
.
Delete names– Press the PTT button. – Give the command
DELETE NAMES/NAME
after the signal tone.
After giving this command, there is the possibility to erase a stored entry in the phone voice phone book. Example for erasing an entry out of the phone phonebook
Voice command
Announcement
SAVE/STORE NAMES/NAME/NUMBER
“ The name please
”.
COMPANY XYZ
“Please repeat the name
”.
COMPANY XYZ
“The number please
”.
ZERO ONE TWO THREE
“Zero One Two Three
”.
FOUR FIVE SIX
“Four Five Six
”.
If no entry is put in, the following a
nnouncement is made af
ter about 5 seconds.
“Possible commands are: st
ore, repeat, correct,
delete or more digits
”.
STORE
“The name COMPANY XYZ is stored
”.
Voice command
Announcement
SELECT NAMES/NAME
“The name please
”.
COMPANY XYZ
“Company xyz
”.
If no entry is put in, the following anno
uncement is made after about 5 seconds.
“Possible commands are: dial, repeat, correct
”.
DIAL
“The number is being dialed
”.
Voice command
Announcement
DELETE NAMES/NAME
“The name please
”.
COMPANY XYZ
“Do you want to delete the entry Company xyz?
”.
YES
“Delete?
”.
If no entry is put in, the following anno
uncement is made after about 5 seconds.
“Possible commands are: yes, no, repeat, cor- rect
”.
YES
“The name is deleted
”.
se0.1.book Page 150 Frida
y, April 10, 2009 3:19 PM

Communication
151
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
You can interrupt the dialogue at any time
by pressing the PTT button or with the
voice command
CANCEL
.
If the user answers with
NO
, the system answers with “
Cancel
” and the dialogue is
ended.Delete voice phonebook– Press the PTT button. – Give the command
DELETE PHONEBOOK
after the signal tone.
After giving this command there is the
possibility to erase the complete phone
voice phone book or the individually st
ored names out of the phone phone book.
Example for erasing the complete phonebook You can interrupt the dialogue at any time
by pressing the PTT button or with the
voice command
CANCEL
.
Example for erasing individual names out of the phone phonebook As long as the phonebook is read out, ot
her entries can be erased by pressing the
PTT button. You can end the dialogue at any time with the voice command
CANCEL
.
Listening-in to the phonebook– Press the PTT button. – Give the command
LISTEN TO/PLAY PHONEBOOK
after the signal
tone.
After giving this command the phone voice
phone book is read out by the system.
By pressing the PTT button when announcing the desired name, the corresponding telephone number is being dialed; the system answers: “
The number is being
dialed
”.
Voice command
Announcement
DELETE PHONEBOOK
“Do you want to delete the whole phonebook?
”.
If no entry is put in, the following anno
uncement is made af
ter about 5 seconds.
“Possible commands are: yes, no, repeat
”.
YES
“Are you sure?
”.
YES
“The phonebook is deleted
”.
Voice command
Announcement
DELETE PHONEBOOK
“Do you want to delete the whole phonebook?
”
If no entry is put in, the following anno
uncement is made after about 5 seconds.“Possible commands are: yes, no, repeat
”.
NO
The phonebook is read out.
When announcing the entry to be erased, press the PTT button.
“ Do you want to delete (name)?
”
If no entry is put in, the following anno
uncement is made after about 5 seconds.“Possible commands are: yes, no
”.
YES
“The name is deleted
”.
Continue reading out the phone book.
se0.1.book Page 151 Frida
y, April 10, 2009 3:19 PM

Communication
152
Universal telephone preinstallation GSM III*IntroductionThis enables you to make full use of the ad
vantages of a normal carphone (“hands-
free system” using a microphone integrated in the vehicle, optimal transmission of signals using an external aerial etc.). The
equipment includes also the voice control.
The telephone is connected using the
rSAP
profile -
Remote SIM access profile
(telecommunication
of the SIM data)
by means of Bluetooth
® technology, if your
telephone supports this profile. The equi
pment includes the following functions:
•
Display of the SMS text in the information display.
•
Free talking in the vehicle interior.
•
MUTE signal to the radio.
•
Voice control (with the set-up possibility for “short and long dialogue”,
depending on the user's knowledge of the operating structure).•
Convenience mode with the multifunction steering wheel and the display in the
information display.•
Handsfree-system.
The voice control of the telephone is acti
vated by pressing the button PTT on the
multifunction steering wheel
⇒page 154, fig. 164
.
A phone phonebook is part of the univers
al telephone preinstallation GSM III with
voice control. In the phone phonebook ther
e are 1000 free memory locations avail-
able. This phone phonebook is independen
t of the appliance us
ed for the mobile
phone. The volume can be changed at any time with the set button of the radio* or with the function keys on the mult
ifunction stee
ring wheel*.
Dialogue The period, in which the telephone system
is ready to receive voice commands and
carry out the voice commands, is called DIALOGUE. The system gives audible feed- back and guides you if nece
ssary through the relevant functions. You can start or
end the dialogue at any time
by pressing the PTT button.
The dialogue is always automatically ended after carrying out an operation, e.g. after erasing the name from the phonebook. The dialogue of the incoming call is i
mmediately interrupted
and you can accept
the call by pressing the button
.
If a voice command is not detected, the system answers with “
Sorry?
” and a new
entry can be performed. After the 2nd error the system repeats the aid. After the 3rd error the answer “
Cancel
” is given and the dialogue is ended.
Optimum understanding of the voice commands depends on the following factors:•
Speak with a normal tone of voice wi
thout intonation and excessive voice
pauses.•
Avoid insufficient articulation.
•
Close the doors, windows and sliding roof,
in order to reduce or stop disturbing
exterior noise.•
It is recommended to speak
louder at higher speeds, so
that the tone of your
voice is louder than the increased surrounding noise.•
During the dialogue avoid additional nois
e in the vehicle, e.g. simultaneously
talking occupants.•
Do not speak, if the system makes an announcement.
•
The microphone for voice control is in
serted in the moulded headliner and
directed to the driver and front passen
ger. Therefore the driver and the front
passenger can operate the equipment.
WARNING
Pay attention primarily to the traffic situation! As the driver you are fully responsible for road safety. Use the telephone system only to such an extent, so that you are in full control of your vehicle at any time.
Note
•
Should you have any questions, please contact an authorised Škoda Service
Par tner.
se0.1.book Page 152 Frida
y, April 10, 2009 3:19 PM

Communication
153
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
•
Please also refer to the additional instructions
⇒page 142, “Mobile phones
and two-way radio systems”.Bluetooth
®
The equipment enables the wireless connection to the control unit of a telephone with Bluetooth
® function which supports the
rSAP
profile.
Process of connection – Switch on the ignition. – If you have not switched on Bluetooth
® on your telephone, switch it
on.
– For certain mobile phones it is necessary to switch on first the
rSAP

function.
– Press the button
 on the multifunction steering wheel and select
device search
. The system searches mobile devices and shows these
in the information display*.
– Select your telephone in the information display by turning the hand-
wheel and select it by
pressing the handwheel.
– Within 30 seconds enter in your te
lephone the 16 digit PIN of your
control unit, which is indicated in the information display* and confirm it according to the instructions on the display of your tele- phone.
– If your SIM card is blocked by a PIN code, enter the PIN of the SIM card
of your telephone. The telephone
connects to the control unit (during
the first connection you can only se
lect in the information display*
and when the vehicle is stationary
, if the PIN should be stored).
– For the first storage of a new user
follow the instructions in the infor-
mation display.
– To download the telephone book and the indentification data of the
SIM card into the new control unit, confirm again the command
rSAP

in your mobile phone. The sy
stem reads the telephone book.
If you do not want to confirm the command
rSAP
during each connection of the
telephone to the control unit, then you mu
st carry out in the menu of the mobile
phone an authorization using the control unit. The telephone deregisters from the GSM network and only the control unit ensures the communication with the network. In th
e telephone only the interface for Blue-
tooth
® remains active. In this case, you can only
select to separate from the device,
switch off the Bluetooth
® connection or the number of the emergency call 112.
If the PIN was stored, an automatic select
ion and connection of the telephone take
place the next time the ignition is swit
ched. Check on your mobile phone if the
automatic connectio
n was established.
Connection terminated The connection of the handsfree-system is terminated by means of Bluetooth
®:
•
When removing the key from the igniti
on lock (during a telephone call, the
connection is disconnected).•
By switching off the Bluetooth
® in the mobile phone.
•
By selecting “separate telephone” in the menu of the mobile phone.
On vehicles which are fitted out with radio or navigation at the factory, it is possible to terminate the telephone call after remo
ving the key from th
e ignition lock by
pressing the icon on the touch-screen of the radio
17) or the navigation, see oper-
ating instructions for radio or for navigation.
WARNING
•
Pay attention primarily to the traffic situation! As the driver you are fully
responsible for road safety. Use the tele
phone system only to such an extent,
so that you are in full control of your vehicle at any time - risk of accident!•
In the event of air transport, the Bluetooth
® function of the handsfree-
system must be switched of
f by a specialist garage!
17)Does not apply for Radio Swing.
se0.1.book Page 153 Frida
y, April 10, 2009 3:19 PM

Communication
154
Note
•
In the memory of the control unit, up to
three users can be stored, whereby the
handsfree-system can only communicate ac
tively with one user. In the case of
mutual connection with a fourth mobile phone, you must erase one user.•
Not valid for all mobile phones which
enable a communication via Bluetooth
®.
You can ask at an authorised Škoda Service
Partner if your telephone is compatible
with the universal teleph
one preinstallation GSM II.
•
If the telephone book of the mobile ph
one contains more than 1 000 entries,
the system announces a
failure while loading the telephone book
.
•
When connecting to the control unit, follow the instructions on your mobile
phone.•
Note that the range of the Bluetooth
® connection to the handsfree-system is
optimized in the vehicle interior. The rang
e is dependent on local factors, e.g.
obstacles between the devices and interferences with other devices.
Operation of the telephone on the multifunction steering wheel*The driver can set the basic functions of the telephone by simply operating the buttons located on the steering wheel so th
at he can concentrate on the traffic situ-
ation without being distracted as little
as possible by operating the telephone
⇒ fig. 164
.
This applies only if your vehicle has been
equipped with the telephone preinstalla-
tion at the factory. If the side lights are switched on, the buttons on the multifunction steering wheel are illuminated. Overview of the different functions in cont
rast to the multifunction steering wheel
without mobile phone operation
⇒page 139.
Fig. 164 Multifunction steering wheel: Control buttons for the telephone
se0.1.book Page 154 Frida
y, April 10, 2009 3:19 PM

Communication
155
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The buttons operate the functions for
the operating mode of the current
telephone.
Button
Action
Operation
press briefly
Activation and deactivation of the voice control°
(Button PTT - Push to talk)

press button for a long
period of time

 turn upwards
Increase volume

 turn downwards
Decrease volume

 press briefly
Accept call, terminate call, entry in the main me
nu of the telephone, list of selected numbers

 press button for a long
time
Reject call, list of the last calls, entry in the ma
in menu of the telephone, list of selected numbers

 press briefly
Reach one level higher in the menu (according to the current position in the menu)

 press button for a long
time
Return in the main menu of the information display

press briefly
Confirm menu selection

press button for a long
period of time

 turn upwards
The last chosen menu selection, name

 turn downwards
The next menu selection, name

 quickly turn upwards
To the previous initial letter in the telephone book

 quickly turn downwards
To the next initial letter in the telephone book
A1A1A1A1A2A2A3A3A4A4A4A4A4A4
se0.1.book Page 155 Frida
y, April 10, 2009 3:19 PM

Communication
156
Operate the telephone via the information display*If you select the menu point
Te l e p h o n e
on the information display with the aid of
the handwheel , you can chan
ge to the following menus:
„
Phone book
„
Dial number
„
Call register
„
Voice mailbox
„
Messages
„
Bluetooth
„
Settings
„
Back
Phone book In the menu point
Phone book
is the list of the loaded contacts from the telephone
memory and the SIM card of the mobile phone. In the phone phonebook there are 1000 free memory locations available. Dial number In the menu point
Dial number
, you can write any telephone number. Select in
sequence the desired digits with the aid of the handwheel and confirm it by pressing the handwheel. Yo
u can select the numbers
0 - 9
, the symbols
*, #
and the
functions
Delete, Call, Cancel
.
Call register In the menu point
Call register
, you can select the following menu points:
„
Missed calls
„
Received calls
„
Last calls
„
Delete lists
Voice mailbox In the menu point
Voice mailbox
there is a list of messages from the missed calls.
Messages In the menu point
Messages
there is a list of received text messages.
Bluetooth In the menu
Bluetooth
you can select the following menu points:
„
User
- the overview of the stored users
„
New user
- Search for users who are in the reception range
„
Visibility
- Switching on the visi
bility of the telephone unit for other devices
„
Extras„
Headset
„
Modem
„
Phone name
- the possibility to change the name of the telephone unit (pre-
set SKODA-rSAP) Settings In the menu
Settings
you can select the following menu points:
„
Phone book„
Update
„
Select memory„
SIM & phone (SIM & Mobile phone)
„
SIM card
„
Mobile phone
Fig. 165 Information display: Menu telephone
A4
se0.1.book Page 156 Frida
y, April 10, 2009 3:19 PM

Communication
157
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
„
List„
Surname
„
First name
„
Own no. send
- the possibility to suppress one's own number on the unit called
„
Signal settings„
Ring tone
„
Volume
„
Phone settings„
Select operator„
Automatic
„
Manual
„
Off time„
+ 5 Minutes
„
- 5 Minutes
„
GPRS
- Setting of the access point of the user
„
Switch off ph.
- switching off the telephone unit (telephone remains
connected) Back Return in the main menu of the information display.
Note
The readout of the menu
Te l e p h o n e
and the voice control are not possible in the
Russian and Chinese language.
Voice commandsVoice commands for operating
the telephone control unit
Other possible commands
Voice command
Activity
HELP
After this command the system repeats all possible commands.
LO N G D I A LO G U E
Help is not reduced (suitable for beginners).
SHORT DIALOGUE
Help is clearly reduced (good operating knowledge provided).
CALL NAME
After this command a name can be entered which establishes a connection to the requested partner ⇒ page 158.
DIAL NUMBER
After this command a phone number can be entered which establishes a connection to the requested party.
REDIAL
After this command the system selects the last selected number.
Voice command
Activity
CALLS (SELECT)
The telephone number is selected.
REPEAT
The entered name or the digits are repeated. Then the system requests with voice response “
please
proceed
” the entry of further digits or commands.
BACK
The entered name or the last entered order of digits is erased. Previously entered groups of digits are repeated. Then the system requests with voice response “
and proceed?
” the entry of further digits
or commands.
DELETE
All entered digits are erased.
CANCEL
The dialogue is ended.
se0.1.book Page 157 Frida
y, April 10, 2009 3:19 PM

Communication
158
Phone voice phonebook*Store name– Press the button
.
– In the menu telephone, select the menu point
Phone book
and in this
menu point, select a contact of wh
ich you want to record a voice
recording and confirm it with the handwheel
⇒
page 154, fig. 164
.
– Select the menu point
Record
and afterwards
Recording
.
– The system gives the command “
Store name, name please
”.
– Pronounce the name, e. g “Name XYZ”, the system repeats the name.– The system gives the notice “
Name stored
”.
In the case that the system does not understand the spoken name, it gives the notice “
Pardon?
”, “Please repeat the name
”, “The name is too short
” or “
The
name is too long
”.
In the phone voice phonebook up to 15 entries can be stored.For similar names additional information (e.g. first names) should be stored. Voice commands for operating
the phone voice phone book
Example for storing the recording in the phone voice phonebook You can interrupt the dialogue
at any time by pressing
the PTT button or with the
voice command
CANCEL
.
Select name– Press the button PTT
⇒
page 154, fig. 164
.
– Give the command
CALL NAME
after the signal tone.
After giving this command, the system reques
ts the entry of the name to be called.
Example for selecting the name In the case that the list is empty, the message “
The name list is empty, main
menu
” sounds.
If the system does not recognize the name
called, it asks you
to repeat using the
command “
Pardo n?
”. If the system does not recognize the name to be called after
repeating, the message sounds “
The name does not exist. You receive the
current name list with LISTEN TO ALL THE NAMES, main menu
”.
You can interrupt the dialogue
at any time by pressing
the PTT button or with the
voice command
CANCEL
.
Voice command
Activity
LISTEN TO ALL THE
NAMES
After this command the control unit repeats all stored names.
DELETE NAME
After this command, you can enter a name which you would like to erase from the internal phone voice phonebook.
DELETE ALL NAMES
After this command, you can erase the complete list of the stored names.
A4
Voice command
Announcement
STORE NAME
“ The name please
”
Name XYZ
“Please repeat the name
”
Name XYZ
“The name XYZ is stored
”
Voice command
Announcement
CALL NAME
“Call name
”
Name XYZ
“Do you want to call XYZ?
”
CALLS (SELECT)
“The name is being dialed
”
A1
se0.1.book Page 158 Frida
y, April 10, 2009 3:19 PM

Communication
159
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Listening-in to the voice phonebook– Press the PTT button. – Give the command
LISTEN TO ALL THE NAMES
after the signal tone.
After giving this command, all voice record
ings are replayed from the list of the
control unit. By pressing the PTT butto
n when announcing th
e desired name, the
corresponding telephone number is being dialed; the system answers: “
The
number is being dialed
”.
Example for selecting the name In the case that the list is
empty, the system announces “
The name list is empty
”.
You can interrupt the dialogue at any time
by pressing the PTT button or with the
voice command
CANCEL
.
After replaying the complete list, the system announces “
End of name list
”.
Erase entries out of the phone voice phonebook– Press the PTT button. – Give the command
ERASE NAME
after the signal tone.
After giving this command, there is the possibility to erase a stored entry in the phone voice phonebook.
Example for erasing an entry out of the phone voice phonebook You can interrupt the dialogue at any time
by pressing the PTT
button or with the
voice command
CANCEL
.
If the user answers with
NO
, the system answers with “
Cancel
” and the dialogue is
ended.Erase the complete phone voice phonebook– Press the PTT button. – Give the command
DELETE PHONEBOOK
after the signal tone.
After giving this command, there is the
possibility to erase the complete phone
voice phonebook. Example for erasing the complete phone voice phonebook You can interrupt the dialogue at any time
by pressing the PTT
button or with the
voice command
CANCEL
.
If the user answers with
NO
, the system answers with “
Cancel
” and the dialogue is
ended.
Voice command
Announcement
LISTEN TO ALL THE NAMES
“ Interrupt using the voice button
”
Voice command
Announcement
DELETE NAME
“The name please
”
Name XYZ
“Do you want to erase XYZ?
”
YES
“The name is deleted
”
Voice command
Announcement
DELETE ALL NAMES
“Do you want to delete all the names?
”
YES
“Are you sure?
”
YES
“All the names are deleted
”
se0.1.book Page 159 Frida
y, April 10, 2009 3:19 PM