stop start SSANGYONG KORANDO 2012 User Guide

03-12
Auto washer coupled wiper ▶
When turning ON the auto washer switch with IGN ON and intermittent/automatic wiper switch OFF,
the washer fluid is sprayed onto the windshield glass for 2 seconds and the wipers operate 4 times.
After then, additionally, the washer fluid is sprayed for 1.5 seconds and the wipers operate 3 times
again.
The auto washer switch signal is overridden during speed sensitive intermittent wiper, washer
coupled wiper or auto washer coupled wiper operation.
When turning the wiper switch to AUTO position during the operation of auto washer, the auto
washer stops its operation and the intermittent/automatic wiping mode will be started.
The front and rear washer switch signal are overridden during the operation of auto washer. 1.
2.
3.
4.

03-28
Seat belt reminder ▶
Operating conditions for seat belt reminder are as follows: IGN ON, engine running (over 300 rpm),
vehicle speed of 25 km/h or higher, driver seat belt unfastened, passenger seat belt unfastened and
passenger seat occupied. In addition, if the seat belt reminder is activated at the speed of 25 km/h or
higher and the speed reduces to below 25 km/h within 5 minutes, the interior buzzer sound stops. The
buzzer sounds for 5 minutes again when the speed is 25 km/h or higher.
The seat belt reminder stops its operation when fastening the seat belt, but starts the operation again if
unfastening the seat belt.
If the seat belt reminder is initially operated due to unfastened driver seat belt, the buzzer sounds with
the interval of 0.02s ON/1.18s OFF, the instrument cluster sends the driver seat belt warning signal
(SBR) and the seat belt warning lamp stays on.
At this time, the buzzer sounds for 5 minutes.
If the seat belt reminder is operated due to unfastened passenger seat belt when the passenger seat
belt reminder sensor detects that the passenger seat is occupied, the instrument cluster sends the
driver seat belt warning signal and the seat belt warning lamp stays on.
For this case, the indicator shows each status of the driver and passenger seats but the indoor buzzer
is common to both seats.
If the simultaneous operating condition for the indoor buzzer is met, the driver seat has the priority.
If the driver seat belt is fastened, the same operation is also carried out in the passenger seat
automatically.
The buzzer and the warning lamp are operated according to the vehicle speed as below table during
the seat belt reminder operation. 1.
2.
3.
4.
5.
Seat belt reminder operation
<007700990090009600990090009b00a000470096008d00470089009c00a100a1008c0099004700960097008c00990088009b00900096009500610047007a0069007900470d7d00470072008c00a000470099008c009400900095008b008c00990047009e00
880099009500900095008e00470d7d0047007a009c00950099>oof warning ⇒ Tail lamp ON
<009e00880099009500900095008e00470d7d0047006f008800a100880099008b0047009e00880099009500900095008e0047008d00930088009a008f008c009900470d7d0047007b009c009900950047009a0090008e009500880093004700930088009400
970055> 6.
Buzzer Warning lamp
25 Km/h ~ 49 Km/h 0.02s ON / 1.18s OFF Keep ON
50 Km/h ~ 99 Km/h 0.02s ON / 0.98s OFF Keep ON
10 Km/h ~ 49 Km/h 0.02s ON / 0.78s OFF Keep ONFunction
Vehicle speed
Seat belt remind warning lamp (EU only)
This lamp comes on for 6 seconds after turning on the ignition switch. If the vehicle speed goes
over 10 km/h without fastened the seat belt, the inside buzzer sounds. -

03-458710-01
12) Panic Alarm
Panic alarm by REKES signal ▶
When receiving the panic signal with Power OFF, ACC and IGN ON, the horn and turn signal lamps
operate for T1 with the interval of 0.5s ON/0.5s OFF.
When receiving the door lock or panic signal during the panic operation, the panic alarm stops.
(other commands are overridden)
The theft deterrent functions are as below:
- The theft deterrent alarm stops when receiving the panic alarm during its operation.
- The panic alarm stops and then the theft deterrent alarm starts its operation when occurring the
theft deterrent alarm conditions during panic alarm.
This function should be available regardless of the key status.
This function should be activated only when the ignition key is inserted (EU region). 1.
2.
3.
4.
5.

03-46
Panic alarm by SKM smart key's remote control ▶
When the BCM receives "Panic command by smart key remote control" as a BCAN signal, it
activates panic alarm by operating the horn and turn signal lamp for 30 seconds with a interval of
0.5s ON/0.5s OFF. However, the BCM used in EU region is operated when receiving the panic
command from the smart key remote control and the signal that the smart key is in the vehicle with
Power OFF, ACC and IGN ON.
The BCM stops the panic function and operates the function depending on the signal in the event of
following commands during turn signal lamp and horn operation by the "Panic command from smart
key remote control".
The panic alarm stops and then the theft deterrent alarm starts its operation when occurring the theft
deterrent alarm conditions during panic alarm.
All the functions are controlled by SKM and operated by signal from SKM. 1.
2.
3.
4.
Stops panic function activated by "Panic command from smart key remote control" through
BCAN signal
Panic function is activated when receiving other command -
-

03-578710-01
18) Flasher (Blinking) Function
Turn signal lamp control ▶
When the BCM is received the multifunction switch signal, it operates the turn signal lamp
and interior buzzer with the intervals of 400 ms ON/400 ms OFF for 75 times/min.
The turn signal lamps are operational only when IGN1 is ON.
If the turn signal lamp is defective during its operation, the turn signal lamp blinks with the intervals of
300 ms ON/300 ms OFF for 100/min and the interior buzzer sounds with same interval.
Defective conditions by BCM: Open - below load of 3.0 A, Short - over load of 7.0 A (load means lamp
load here)
When turning ON the turn signal switch, the lamp blinks 3 times by the BCM. When turning OFF the
switch during the operation, the turn signal lamp blinks 3 times and goes off.
When turning OFF and then immediately ON the turn signal switch during auto blinking operation of 3
times, the turn signal lamp blinks additional 3 times.
When turning ON another turn signal switch during the operation, currently operated turn signal lamp
stops immediately and another turn signal lamp starts blinking. 1.
2.
3.
4.
5.
6.
7.

03-58
Right turn signal lamp control ▶
When the BCM is received the multifunction right turn signal lamp switch signal, it operates the right
turn signal lamp and interior buzzer with the intervals of 400 ms ON/400 ms OFF for 75 times/min.
When turning OFF the right turn signal switch during its operation, the turn signal lamp and buzzer
stop the operation.
The turn signal lamps are operational only when IGN1 is ON.
If the turn signal lamp is defective during its operation, the turn signal lamp blinks with the intervals of
300 ms ON/300 ms OFF for 100/min and the interior buzzer sounds with same interval.
Defective conditions by BCM: Open - below load of 3.0 A, Short - over load of 7.0 A (load means lamp
load here)
When turning ON the turn signal switch, the lamp blinks 3 times by the BCM. When turning OFF the
switch during the operation, the turn signal lamp blinks 3 times and goes off.
When turning OFF and then immediately ON the turn signal switch during auto blinking operation of 3
times, the turn signal lamp blinks additional 3 times.
When turning ON the left turn signal switch during the right turn signal lamp operation, the right turn
signal lamp stops immediately and the left turn signal lamp starts blinking. 1.
2.
3.
4.
5.
6.
7.

04-118712-03
(2) Passive LOCK
When the system searches for a smart key by the input from the outside door handle switch, the SKM
sends the passive LOCK signal to the BCM if all the doors are closed and a normal smart key is found
outside the vehicle.
Passive LOCK hardware control ▶
The SKM sends the door LOCK/UNLOCK signal to the BCM through the BCAN network when a
smart key is verified after the signal from the driver/passenger outside door handle switch is received
through the hardware.
The SKM sends the signal to the BCM and instrument cluster when the warning and indicator
display conditions are met. 1.
2.
Passive LOCK by outside door handle switch ▶
When the ignition status is OFF, ACC ON or IGN ON, the SKM performs the verification procedure if the
LOCK signal is received from the driver/passenger door handle switch.
When the outside door handle switch is operated, the SKM verifies if a smart key is outside the
vehicle using the corresponding exterior antenna.
The SKM sends the signal for [Passive LOCK command] to the BCM through the BCAN if a smart
key is identified as being outside the vehicle.
If no smart key is verified as being outside the vehicle, this process is stopped and restarted when the
next signal is received from the outside door handle switch.
When the driver's door is unlocked with the ignition status ACC ON, the SKM changes the ignition
status to OFF and sends the signal for [Passive LOCK command] to the BCM through the BCAN to
lock the door. The BCM ignores the signal if the ignition status is IGN ON.
The SKM recovers the deactivated smart key function inside the vehicle when it receives the theft
deterrent deactivation signal from the BCM through the BCAN communication. 1.
2.
3.
4.
-

04-12
The system first identifies the last smart key used, and then identifies all the other registered smart
keys until a normal smart key is verified.
The system identifies the smart keys by using the outside door handle antenna on the door handle
switch which has sent the signal.
Smart key search input: The last door is opened and then closed. Outside door handle switch, Brake
switch, START switch (Tailgate open request) 1.
2.
3.Smart key search mode ▶Searching for other keys ▶
When the ignition status is IGN ON or ACC ON, the SKM starts to verify the smart key if any door is
opened and then closed. If one or more smart keys are verified as being in the vehicle, the smart key
verification procedure is stopped. If no verified smart key is identified as being in the vehicle, the SKM
sends the signal which identifies that there is no verified key inside the vehicle to the BCM and instrument
cluster through the BCAN (Smart key not identified warning).Interruption of door LOCK & Smart key function by outside door handle switch ▶
When the door LOCK signal is received from the driver/passenger door handle switch with the ignition
status OFF or ACC ON, the SKM identifies the verified smart key and sends the passive LOCK signal
to the BCM through the BCAN if the ignition is turned to OFF.
The SKM receives the theft deterrent mode information signal from the BCM through the BCAN.
If there is any verified smart key in the vehicle, the function of the verified smart key is interrupted. 1.
2.
3.

04-138712-03
(3) Passive UNLOCK
When the system searches for a smart key by the input from the outside door handle switch, the SKM
sends the passive UNLOCK signal to the BCM if all the doors are closed and a normal smart key is
found outside the vehicle.
Passive UNLOCK hardware control ▶
The SKM sends the door LOCK/UNLOCK signal to the BCM through the BCAN network when a
smart key is verified after the signal from the driver/passenger outside door handle switch is received
through the hardware. 1.
Passive UNLOCK by outside door handle switch ▶
When the ignition status is OFF, ACC ON or IGN ON, the SKM starts to verify the smart key if below
conditions are met.
When the driver or passenger door handle switch is operated, the SKM verifies if a smart key is outside
the vehicle using the corresponding antenna.
When the outside door handle switch is operated, the SKM verifies if a smart key is outside the
vehicle using the corresponding exterior antenna.
The SKM sends the signal for [Passive UNLOCK command] to the BCM through the BCAN if a
smart key is identified as being outside the vehicle.
If no smart key is identified as being outside the vehicle, this process is stopped and restarted when
the next signal is received from the outside door handle switch.
When the driver's door is locked with the ignition status ACC ON or IGN ON, the SKM sends the
signal for [Passive UNLOCK command] to the BCM through the BCAN to unlock the door without
changing the ignition status to OFF. 1.
2.
3.
4.
Smart key search mode ▶
The system first identifies the last smart key used, and then identifies all the other registered smart
keys until a normal smart key is verified.
The system identifies the smart keys by using the outside door handle antenna on the door handle
switch which has sent the signal.
Smart key search input: The last door is opened and then closed. Outside door handle switch, Brake
switch, START switch (Tailgate open request)
Exceptional mode
When operating the door handle switch, the system changes the smart key searching conditions in
vehicle inside and outside according to the theft deterrent mode.
- Searching sequence when disarmed by BCM: Inside > Outside
- which function is restricted when the BCM is in theft deterrent mode. 1.
2.
3.
4.

04-14
(4) Passive tailgate open
When a normal smart key is found by the signal from the tailgate open switch, the system sends the
tailgate open control signal to the BCM.
Passive tailgate open hardware input/output control ▶
The SKM receives the tailgate open switch signal from the BCM through the BCAN communication.
The SKM sends the tailgate open output signal to the BCM through the BCAN communication. 1.
2.
Tailgate open switch control ▶
Tailgate closed -> open
When the ignition status is OFF, ACC ON or IGN ON, the SKM starts to verify the smart key in the
tailgate open actuation area after receiving the tailgate open signal for [tailgate open request] from the
BCM through the BCAN.
The SKM sends the signal for [Passive tailgate open] to the BCM through the BCAN to open the
tailgate and deactivate the theft deterrent mode if a smart key is identified as being outside the vehicle.
If no smart key is identified as being outside the vehicle, this process is stopped and restarted when
the next tailgate open request signal is received. 1.
2.
Smart key search mode ▶
The system first identifies the last smart key used, and then identifies all the other registered smart
keys until a normal smart key is verified.
If the tailgate antenna identifies a normal smart key, the system searches for a smart key in inside
area of the tailgate and inside the vehicle.
The tailgate is opened only when a valid smart key is found within the tailgate antenna range, and the
tailgate is not operated by a smart key in inside area of the tailgate.
Smart key search input: The last door is opened and then closed. Outside door handle switch, Brake
switch, START switch (Tailgate open request) 1.
2.
3.
4. Tailgate open -> closed
When the tailgate is closed with all the other doors are closed, the SKM sends the signal for [smart
key inside the vehicle] through the BCAN if there is a verified smart key inside the vehicle.
When the tailgate is opened and then closed in theft deterrent mode, the signals for [external buzzer]
and [smart key detect warning] are sent for 10 sec. through the BCAN if there is a verified smart key
inside the vehicle. -