lock SSANGYONG KORANDO 2013 Owners Manual

8712-03
3) ESCL Retry Control
When the UNLOCK retry occurs after ESCL LOCK command, the ESCL LOCK is performed. 1.
2.
The UNLOCK retry is possible up to 2 times automatically. If the UNLOCK retry occurs 3 times in
succession, the ESCL NOT LOCKED warning is triggered.
Reactivates when the ESCL LOCK conditions are met. -
-
When the LOCK retry occurs after ESCL UNLOCK command, the ESCL UNLOCK is performed. 4.
The LOCK retry is possible up to 2 times automatically. If the LOCK retry occurs 3 times in succession,
the ESCL JAM warning is triggered.
Reactivates when the ESCL UNLOCK conditions are met by pressing the START/STOP switch. -
-
When the UNLOCK retry occurs after ESCL UNLOCK command, the command will be overridden
without retry. 5.
After the command is overridden, the ESCL JAM warning is triggered.
Reactivates when the UNLOCK conditions are met by pressing the START/STOP switch after
ESCL LOCK. -
- When the LOCK retry occurs after ESCL LOCK command, the command will be overridden without
retry. 3.
ESCL NOT LOCKED warning is triggered.
Reactivates when the UNLOCK conditions are met by pressing the START/STOP switch. -
-

(2) Smart Key Detected Warning (Smart Key Found Inside Vehicle)
Smart key deactivation warning
The ignition is turned OFF or ACC is turned ON.
A verified smart key found in the vehicle with all doors (including tailgate) closed.
The REKES LOCK or passive LOCK signal is input with a valid smart key from the outside the
vehicle.
The SKM sends the theft deterrent mode signal to the BCM through B-CAN and the verified smart
key is found inside the vehicle.
The SKM sends the smart key detected warning to the BCM and instrument cluster through B-CAN.
The BCM activates the buzzer for up to 10 seconds at intervals of 0.5 sec. ON/0.5 sec. OFF and
turns on the smart key detected warning indicator on the instrument cluster. 1.
2.
3.
4.
5.
6.
Smart key inside vehicle warning
The ignition is turned ON or OFF, or the ACC is turned ON.
A verified smart key found only in the vehicle (including emergency slot) with all doors (including
tailgate) closed.
The passive LOCK signal is input without a valid smart key from the outside the vehicle.
The SKM sends the theft deterrent mode signal to the BCM through B-CAN and the verified smart
key is found inside the vehicle.
The SKM sends the smart key detected warning to the BCM and instrument cluster through B-CAN.
The BCM activates the buzzer for up to 10 seconds at intervals of 0.5 sec. ON/0.5 sec. OFF and
turns on the smart key detected warning indicator on the instrument cluster. 1.
2.
3.
4.
5.
6.Smart key detected warning deactivation conditions
- The theft deterrent mode is deactivated.
Smart key detected warning deactivation conditions
- No smart key is found inside the vehicle when a door is opened and then closed.

Ignition status change*
If above conditions are met again, the SKM re-verifies the transponder and sends the verification
status for another 10 sec.
When the ignition status is changed by a smart key verification while the transponder verification is
processed, the SKM sends the signal for [transponder verification fail], and sends the smart key
verification status for 10 sec. -
-
(6) Transmission position warning
When the gear selector lever is in a position other than P or N with IGN ON and engine started, the
SKM sends the [gear position warning] signal to the instrument cluster through the BCAN for up to 10
sec. until the operating conditions are deactivated.
Transmission position warning deactivation
When re-attempting to start with IGN1 ON and transmission in P or N -
(7) ESCL JAM warning
The SKM transmits the warning active command to the BCAN through the BCAN signals such as ESCL
NOT LOCKED warning signal or ESCL JAM warning signal within 10 seconds or until the active
command deactivation conditions will be met, if jam is occurred when the electric steering motor is
locked/unlocked.
Failure Detecting Conditions
When the UNLOCK retry occurs after ESCL LOCK command, the ESCL LOCK is performed.
- The UNLOCK retry is possible up to 2 times automatically. If the UNLOCK retry occurs 3 times
in succession, the ESCL NOT LOCKED warning is triggered.
- Reactivates when the ESCL LOCK conditions are met.
When the LOCK retry occurs after ESCL LOCK command, the command will be overridden without
retry.
- After the command is overridden, the ESCL NOT LOCKED warning is triggered.
- Reactivates when the LOCK conditions are met by pressing the START/STOP switch after
ESCL UNLOCK.
When the LOCK retry occurs after ESCL UNLOCK command, the ESCL UNLOCK is performed.
- The LOCK retry is possible up to 2 times automatically. If the LOCK retry occurs 3 times in
succession, the ESCL JAM warning is triggered.
- Reactivates when the ESCL UNLOCK conditions are met by pressing the START/STOP
switch.
When the UNLOCK retry occurs after ESCL UNLOCK command, the command will be overridden
without retry.
- After the command is overridden, the ESCL JAM warning is triggered.
- Reactivates when the UNLOCK conditions are met by pressing the START/STOP switch after
ESCL LOCK. 1.
2.
3.
4.

8010-01
Status Supervision type
LCD display
The ESCL (Electric Steering Column Lock) is a device to lock the steering handle
using an electric signal, not a mechanical type and shows the messages above if the
relevant systems are faulty.
4) ESCL
5) LCD display
Status Old New
LCD display
Bar graph border maintained when adjusting illumination brightness
Average fuel economy and instant fuel economy displayed simultaneously
-
Auto cruise indicator and supervision cluster DOT LCD graphic added for gasoline
engine ? newly adopted ?
-
DOT LCD winter mode deleted

8010-01
Indicator
(green)
Hazard indicator
ECO indicator
Cruise control indicator
Indicator
(red)
Indicator
(green)
Indicator
(green)
4WD LOCK indicator
Indicator
(red)
4WD check warning lamp
This indicator comes on when the cruise control system is activated.
This indicator goes off when the brake pedal is depressed. (auto cruise
deactivated)
This warning lamp comes on when the 4WD LOCK switch is pressed.
This indicator goes off when pressing the switch again.
This warning lamp comes on when the 4WD system is defective. This indicator comes on when the hazard warning flashers are switched on.
(applies to STD class)
This indicator comes on when the ECO cruise system is activated.
This indicator goes off when the brake pedal is depressed. (ECO
deactivated)

8010-01
The pre-warning of the MICOM control warning is performed 400 ms after turning the ignition switch to
ON position.
IGN ON detecting time: 40~80 ms after turning ignition switch to ON position -
- The pre-warning is performed for 4 seconds after turning the ignition switch to ON position. BCM checks
that the warning lamps (ABS, ESP, ESP OFF, 4WD CHECK, 4WD LOCK) are matched with CAN
signals.
The pre-warning is performed by the variant code.

8010-01
The pre-warning of the MICOM control warning is performed 400 ms after turning the ignition switch
to ON position.
IGN ON detecting time: 40~80 ms after turning ignition switch to ON position -
- The pre-warning is performed for 4 seconds after turning the ignition switch to ON position. BCM checks
that the warning lamps (ABS, ESP, ESP OFF, 4WD CHECK, 4WD LOCK) are matched with CAN
signals.
The pre-warning is performed by the variant code.

Pin No.Message
Operating condition
Domestic Export
Smart key
warningThis message comes on the LCD display, if the smart
key is not in the vehicle when the door is open and
closed in the ignition ON or ACC mode.
This message comes on the LCD display for approx. 10
seconds, if the ignition switch is pressed when the smart
key is not in the vehicle.
This message comes on the LCD display for approx. 10
seconds, if the smart key verification fails after inserting
the smart key into the key holder.
LCD display shows this message and Smart key
reminder sounds for 10 seconds when you open the
in the Smart key holder.
This message informs the driver that the brake pedal
should be depressed and the ignition switch be pressed
in order to start the engine, if the ignition is switched to
ACC mode for more than one time when the driver keeps
pressing the ignition switch without depressing the brake
pedal.
LCD display shows this message when you press the
ignition switch without depressing the clutch pedal.
This message comes on for approx. 10 seconds to
inform the driver that the ignition switch should be
pressed with the shift lever in P in order to start the
engine.
When a Smart key is inside the vehicle and all doors are
closed, LCD display shows this message if you press the
Lock button on the other Smart key.
Pin No. Message Operating condition

8010-01
Pin No. Message Operating condition
Domestic Export
Tire alignment
(applies to
vehicle with
EPS)
CAN scan(This message goes off when all the CAN signal inputs
are normal)
ESCLLCD display shows this message when ESCL (Electric
Steering Column Lock) system is defective. There is
no specific ESCL warning light on the instrument
cluster.
This problem could be temporary. Turn the ignition off
and then on again to check if this message will be
disappeared.
This message helps the driver to predict the driving
direction since the tire alignment is displayed on the
instrument cluster.
The images on the left show that the tires are
aligned to the left. When the tires are aligned to the
right, the image is symmetrical vertically.
Tire alignment is displayed between level 0 and
level 5 depending on the alignment degree when
the ignition switch is turned to "ON" position from
"OFF" position with the shift lever in "P" or "N"
position. While the images up to level 2 comes on
for 5 seconds, the images from level 3 stay on.
These messages are not displayed when the EPS
check message is displayed. -
-
-
-
Pin No. Message Operating condition

Lower main switch
Item Specification
Lower main switch4WD LOCK switch DC 12V - 0.1A
ESP OFF switch DC 12V - 0.1A
Steering wheel heating switch DC 12V - 0.1A
Center fascia switch
Item Specification
Center fascia switchHazard warning flasher switch DC 12V - 0.1A (max. 30 mA)
TRIP/RESET switch DC 12V - 0.1A (max. 30 mA)
Windshield heating switch DC 12V - 0.1A (max. 30 mA)
Rear glass and outside rearview mirror
heating switchDC 12V - 0.1A (max. 30 mA)
Power window main switch
Item Specification
Power window main
switchRated voltage
DC 12 V
Operating voltage DC 9 to 16 V
Rated loadAUTO switch 0.7 A (motor load)
AUTO/MANUAL switch 10 A (motor load)
Window lock switch 10 A (motor load)
Door unlock switch 0.4 A (motor load)
Power window sub switch
Item Specification
Power window sub
switchRated voltage DC 12 V
Operating voltage DC 9 to 16 V
Rated load Manual switch 10 A (motor load)