check engine SSANGYONG MUSSO 1998 Workshop Repair Manual

1F1-26 M162 ENGINE CONTROLS
IDLING CONTROL AND ELECTRONIC PEDAL SYSTEM TEST
Þ 2.1· Ignition:ON
50 512.25 - 2.75 V· ·· ·
· Pedal valve
sensor:
- Power
supply

(potentiometer 2)
· Cable
· ECU
Failure
codeItem
Þ 1.0
Checking method
· Ignition:ON
· Position of
accelerator pedal:
- Closed throttle
position
- Full throttle with kick
down
Test
stepRequirement
Specified
valuePossible cause
31 47
0.3 - 0.7 V
· ·· ·
· Pedal valve
sensor:
- Signal

(potentiometer 1)
160,
161,
164,
167,
4.3 - 4.8 V
· Þ 1.1
· Cable
· Pedal valve sensor
Þ 1.1
· Ignition:ON
31 324.75 - 5.25 V· ·· ·
· Pedal valve
sensor:
- Power
supply

(potentiometer 1)
· Cable
· ECU
Þ 2.0
· Ignition:ON
· Position of
accelerator pedal:
- Closed throttle
position
- Full throttle with kick
down 50 48
0.1 - 0.4 V
· ·· ·
· Pedal valve
sensor:
- Signal

(potentiometer 2)
162,
163,
164,
167,
2.1 - 2.5 V· Þ 2.1
· Cable
· Pedal valve sensor
Þ 3.0
· Engine:in idling
84 87
0.3 - 0.9 V· ·· ·
· Throttle
valve
actuator:
- Signal
Throttle valve
potentiometer 1104,
105,
108,
109,
116,
119,
185,
4.0 - 4.6 V· Þ 3.1
· Cable
· E-GAS actuator
· Position of
accelerator pedal:
- Closed throttle
position
- Full throttle with kick
down

M162 ENGINE CONTROLS 1F1-27
Failure
codeItem
Checking method Test
stepRequirementSpecified
valuePossible cause
Þ 3.1· Ignition:ON
84 1124.75 - 5.25 V· ·· ·
· Throttle
valve
actuator:
- Power
supply(5V)· Cable
· ECU
Þ 4.0
· Ignition:ON
68 670.8 - 2.3 V
The value will
be changed in
1.0 - 2.5V.· ·· ·
· Throttle
valve
actuator:
- Signal
Throttle valve
actuator
motor voltage
supply104,
105,
108,
109,
116,
119,
185,· ECU
· Cable
· E-GAS actuator
· Engine:in idling
- Coolant
temperature:
>70 °C 84 85
4.0 - 4.6 V Throttle valve
potentiometer 2
0.3 - 0.9 V
· Position of
accelerator pedal:
- Closed throttle
position
- Full throttle with
kick down
Throttle valve
potentiometer
1+2
· Ignition:OFF
< 10 W
Throttle valve
actuator
motor
resistance68 67

1F1-28 M162 ENGINE CONTROLS
AIR CONDITIONER CONTROL SYSTEM TEST
Þ 2.0· Engine:In idling
· Air conditioner
switch : ON/OFF
Air conditioner
switch : OFF
Air conditioner
switch : ON
Coolant temperature:
above 105 °C 10 35
11 - 14 V
11 - 14 V
< 1 V
· ·· ·
· Condenser
fan(HI)
control:· Condenser fan
relay
· Fan motor
· ECU
Failure
codeItem
Þ 1.0
Checking method
· Engine:In idling
· Air conditioner
switch : ON/OFF
Air conditioner
switch : OFF
Air conditioner
switch : ON
Te s t
stepRequirement
Specified
valuePossible cause
10 44
< 1 V
· ·· ·
· Air
conditioner
signal:
- Input signal
(input signal
from thermo
amplifier)44,
45,
11 - 14 V· Þ 5.1
· Cable
· Thermo amp
· Auto amp
· Dual pressure
switch
· Air conditioner
control panel
Þ 1.1
· Engine:In idling
· Air conditioner
switch : ON/OFF
Air conditioner
switch : OFF
Air conditioner
switch:ON 10 27
< 1 V
· ·· ·
· Air
conditioner
compressor:
- Output
signal
11 - 14 V
· Thermo amp
· Auto amp
· Dual pressure
switch
· Air conditioner
control panel
· ECU

1F1-30 M162 ENGINE CONTROLS
Failure
codeItemChecking method Te s t
stepRequirementSpecified
valuePossible cause
3.2 - 3.6 bar· ·· ·
· Fuel
pressure:in
idling speed
- When the
vacuum is
applied· Engine:in idling
- Close the valve
screw on pressure
testerÞ 1.0 Connect the fuel
pressure test plug to
the pressure tester
(refer to the flgure on
previous page).· Þ Fuel pump test
· Fuel pressure
regulator
3.7 - 4.2 bar
· ·· ·
· Fuel
pressure:in
idling speed
- When the
vacuum is
not applied· Engine:in idling
- Close the valve
screw on pressure
tester Þ 2.0 Connect the fuel
pressure test plug to
the pressure tester
(refer to the flgure on
previous page).· Fuel pressure
regulator
> 3.0 bar
· ·· ·
· Fuel system
internal
leakage:· Engine:stop Þ 3.0 Connect the fuel
pressure test plug to
the pressure tester
(refer to the flgure on
previous page).· The pressure drops
rapidly:non-return
valve in fuel pump
> 2.5 bar· After 30 minutes from
engine stop· The pressure drops
slowly:
- Injector test
- Fuel pressure
regulator
- O-ring

1F1-32 M162 ENGINE CONTROLS
Failure
codeItemChecking method Test
stepRequirementSpecified
valuePossible cause
1 liter of fuel
supply for
max. 35
seconds· ·· ·
· Fuel pump:
- Fuel supply
ratio· Ignition:ON
- Disconnect the fuel
return pipe and
connect the host to
beaker to collect the
supplied fuel Þ 1.0· Þ 2.0
· Check the fuel line
5 - 9 A
· ·· ·
· Fuel pump:
- Current
consumption· Ignition:ON
- Remove the fuel
relay from the fuse
and relay box in
luggage
compartment and
connect the
amperemeter
between No.1 and
No.3 in relay
box(fuel pump relay
removed position)
for measuring
current consumption Þ 2.0· Fuel pump
533
Multi tester(DC current)
31

1F1-34 M162 ENGINE CONTROLS
Figure 9. Shop Made Cable Figure 10. Fuel Injector Normal Spary Pattern
Failure
codeItemChecking method Test
stepRequirementSpecified
valuePossible cause
There should
be no leaks
and later
drops from
the injector· ·· ·
· Injector:
- Leakage test· Ignition:ON
- Remove the fuel
distributor and fuel
injector with a unit. Þ 1.0
The spray
pattern of the
injector most
show in the
figure 10.
· Ignition:ON
- Connect the shop
made cable to the
injector
- Collect the spraying
fuel with a beaker
- Connect the shop
made cable to
No.21(+) and No.3
(-) terminal in test
box Þ 2.0· Injector
533
· ·· ·
· Injector:
- Function test
and spray
pattern
check
533

M162 ENGINE CONTROLS 1F1-47
3. Disconnect the vacuum hose.
4. Disconnect the circlip and remove the fuel pressure
regulator.
5. Apply the oil to O-ring lightly and then replace it.
6. Installation should follow the removal procedure in the
reverse order.
7. Check for fuel pressure and internal leaks by operating the
engine. 2. Discharge the pressure in fuel supply system by pressing
the service valve.
Removal & Installation Procedure
1. Remove the fuel pressure test connector.

M162 ENGINE CONTROLS 1F1-51
Removal & Installation Procedure
1. Discharge the fuel pressure from the fuel pressure test
connector.
2. Disconnect the battery ground cable.
3. Disconnect the vacuum hose from the fuel pressure
regulator.
4. Remove the cable guide.
5. Remove the fuel return and supply line.
Notice
lFor removal, cover around parts with cloths not to be
stained by fuel.
lIn case of checking the injector only, do not remove the
fuel return and supply line.
Installation Notice
6. Remove the six injector connectors.
7. Remove the two left and two right bolts and one center bolt
of the fuel distributor assembly from the intake manifold.
Installation Notice
Tightening Torque25 - 30 Nm
Tightening Torque 22.5 - 27.5 Nm

1F1-52 M162 ENGINE CONTROLS
8. Remove the injectors and the fuel distributor carefully.
9. Installation should follow the removal procedure in the
reverse order.
10. Check for fuel pressure and internal leakage by operating
the engine.
Fuel Pressure Test
1. Turn the ignition switch to "OFF" position.
2. Remove the fuel pressure test connector.
Vacuum Hose Connected (bar) 3.2 - 3.6
Vacuum Hose Disconnected (bar) 3.7 - 4.2
5. Replace the pressure regulator diaphragm if out of the
specification. 3. Connect the fuel pressure gauge to the fuel pressure test
connector.
4. Test the fuel pressure at idling by operating the engine.

M162 ENGINE CONTROLS 1F1-53
3. If there is no change in fuel pressure and maintain the
following pressure over 30 minutes, it is normal.
Internal Leakage Test
1. Connect the fuel pressure gauge to the fuel pressure test
connector.
2. Stop the engine for approx. 30 minutes and then check the
fuel pressure changes.
Fuel pressure
drops slowly
·Fuel leakage at the
injector
• Faulty fuel pressure
regulator's
diaphragm and O-
ring.
Fuel pressure
drops rapidly• Faulty check valve
in the fuel pump.
Possible Cause Pressure Change
Fuel Pressure(bar) 2.5
Discharging the pressure in fuel system
1. Remove the fuel pressure test connector.
Installation Notice
2. Remove the fuel pressure in fuel system by pressing the
service valve with a clean, pointy tool.
Notice
Place a cloth so that the fuel doesn't stain around.
Tightening Torque 22.5 - 27.5 Nm