radiator SSANGYONG MUSSO 1998 Workshop Owner's Guide

1D3-4 OM600 ENGINE COOLING
COOLING SYSTEM LEAKAGE TEST
Tools Required
124 589 15 21 00 Tester
Test
1. Loosen the pressure cap by 1 notch and remove the cap
after.
Notice
Do not remove radiator cap when coolant is above 90°C.
2. Add the coolant to the arrow mark of coolant reservoir.
3. Connect the special tool to the injector of reservoir and apply
1.4bar pressure.
Tester 124 589 15 21 00
4. If the pressure on the tester drops, check the hose, pipe
and leakage and, replace or retighten.

OM600 ENGINE COOLING 1D3-5
DRAIN AND FILLING OF COOLANT
Preceding Work : Removal of skid plate
Drain / Filling
1. Loosen the pressure cap of reservoir by 1 notch and remove
pressure and then loosen the cap.
Notice
Do not remove radiator cap when coolant is above 90°C.
2. Open the drain plug and drain the coolant.
Notice
Collect the coolant by using the proper bottle.
3. Remove the drain plug(1) and seal(2) of cylinder block and
drain the coolant.
4. Replace the seal to new one and tighten the drain plug
Installation Notice
Tightening Torque 30 Nm
5. Tighten the drain plug of the lower radiator.
6. Fill the coolant through coolant reservoir-tank.
Notice
lA proportion of 50% by volume of water / anticorrosion
must be ensured
7. After engine is running at idle speed, check the level of
coolant. If necessary, add enough specified coolant.
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE

1D3-12 OM600 ENGINE COOLING
RADIATOR
Preceding : Removal of cooling fan shroud
1 Radiator Inlet Hose...............OM662LA : 220mm
.............................................OM661LA : 321mm
2 Radiator outlet Hose
3 Radiator Deaeration Tube & Hose
4 Clamp5 Spring Clamp
6 Bolt..........................................................3-7 Nm
7 Radiator
8 Spring Clamp
9 Bolt...........................................................3-7Nm

OM600 ENGINE COOLING 1D3-13
Removal & Installation Procedure
1. Drain coolant from the radiator.
2. Remove the coolant thermoswich connector from radiator.
3. Remove the each coolant hose.
4. Remove the auto T/M oil cooling hose and cooling line.
Installation Notice
5. Loosen the radiator upper mounting bolt and remove the
mounting stopper and insulator.
6. Remove the radiator.
7. Check the radiator pin for crack, leakage and bending and
replace it if necessany.
8. Installation should follow the removal procedure in the
reverse order.
Tightening TorqueHose : 29 - 40Nm

1D3-14 OM600 ENGINE COOLING
COOLING SUB-SYSTEM
1 Radiator
2 Cooling Fan Shroud
3 Bolt.......................................................... 3-7Nm
4 Cooling Fan Shroud
5 Radiator Deaieration Hose7 Mounting Bracket
8 Make-up Cooling Hose
9 Bolt...........................................................3-7Nm
10 Cooling Reservoir-tank Cap
11 Cooling Reservoir-tank

OM600 ENGINE COOLING 1D3-15
Removal & Installation Procedure
Cooling Fan Shroud
1. Remove the radiator deaeration hose and tube.
Installation Notice
Tightening Torque 3 - 7 Nm
Tightening torque 3-7Nm
2. Check the shroud.
3. Installation should follow the removal procedure in the
reverse order.
Coolant Sub-Tank
1. Drain the coolant from radiator.
2. Remove the each hose.
3. Loosen the mounting bolt of sub-tank and remove the
coolant sub-tank.
Installation Notice
4. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 3 - 7 Nm

7B/C-14 MANUAL & SEMIAUTO-HVAC
CONDENSER
Preceding Work : Removal of the radiator
1 Bolt
2 Condenser Fan
3 Bolt
4 Condenser
Diesel Engine

BUMPERS AND FASCIAS 9O-3
Mounting Inspection
1. Clearance between the upper bumper and radiator grille.
2. Clearance between the upper bumper and headlamp
moding.
Clearance
12 ± 1.0 mm
Clearance
9 mm
2. Clearance between the bumper and wheel arch.
Clearance
10 mm