SSANGYONG MUSSO 1998 Workshop Repair Manual

2D-10 REAR SUSPENSION
Removal & Installation Procedure
1. Disconnect actuator connector and unscrew bolt and remove
actuator assembly.
Notice
lWhen installing the actuator to the mounting bracket,
the wiring should face outward of the frame.
lActuator wiring should be fixed 40 - 50mm away from
the wiring ends when fixing it with the frame open clip.
2. Unscrew the upper nut (6).
Notice
When screwing the nut, actuator contacting surface of the
mounting bracket and rod end should be 0.5 - 1.5mm.
3. Remove the mounting bracket (5).
Notice
When installing the bracket, it should be parallel to the frame
side member.
4. Remove the bush and check for damage and replace if
necessary.
5. Unscrew shock absorber lower bolt and nut and remove
the shock absorber.
Notice
Shock absorber is filled with gas, never attempt to cut or
heat.
6. Installation should follow the removal procedure in the
reverse order.

Description
Alumimun
7JJ X 15
Radial Tire
P215 / 75R 15 - 30psi
P235 / 75R 15 - 30psi
P255 / 70R 15 - 30psi Application
Wheel
SECTION 2E
TIRES AND WHEELS
TABLE OF CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Wheel BoltNlm
80 - 120
110 - 130
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 2E-1
General Specifications . . . . . . . . . . . . . . . . . . 2E-1
Fastener Tightening Specifications . . . . . . . . . 2E-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 2E-2
Wear Pattern Diagnosis . . . . . . . . . . . . . . . . . 2E-2
Identification . . . . . . . . . . . . . . . . . . . . . . . . . 2E-3
Radial Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 2E-3Wheel Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 2E-3
Component Locator . . . . . . . . . . . . . . . . . . . 2E-4
Wheel and Tire . . . . . . . . . . . . . . . . . . . . . . . . 2E-4
Maintenance and Repair . . . . . . . . . . . . . . . 2E-5
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 2E-5
Wheels and Tires . . . . . . . . . . . . . . . . . . . . . . 2E-5
Material
Size
Tire
Type
Size and Tire Pressure
Steel
Alumimum

2E-2 TIRES AND WHEELS
DIAGNOSIS
WEAR PATTERN DIAGNOSIS
Wear Pattern Possible CauseRemedy
Wear on Both Tread Shoulders Under Inflation
Wear on Tread Center
Over Inflation
Tread Torn Out Under Inflation
One-sided Tread WearIncorrect Camber or Toe-in
Feather Edging of TreadIncorrect Toe-in
Spotty Tread Wear
Out of Wheel Balance
Spotty Wear-wear Localized on
Shoulder SectionsOut of Wheel Balance
Play in Hub Bearings
Play in Ball Joint
Defective Shock Absorber
Adjust
Adjust
Adjust
Adjust
Adjust
Adjust
Adjust
Check play
Adjust preload
Check
Check

TIRES AND WHEELS 2E-3
IDENTIFICATION
RADIAL TIRE
WHEEL DISC
7 J x
16 ET 39
Wheel Offset (mm)
(Distance from rim center to wheel
nave contacting surface)
Rim Diameter (inch)
Identification for One-piece Well-base Rim
Code Letter for Height and Profile of Rim Flange
Rim Width (Inch)
ET : Distance from Rim Center to Wheel have Contacting
Surface (mm)
a : Rim Width (Inch)
d : Rim Diameter (Inch)
Four Season Mud & Snow P 215/75 R 15 94 H M+S
Speed Rating (max. 210km/h)
Load Range (below 670kg)
Rim Diameter (inch)
Radial Tire
Aspect Ratio = (Section Height ¸ Section
Width) x 100
Section Width (mm)
Passenger Car
215/65 R 16 93 V
Speed Rating (max. 240km/h)
Load Range (below 650kg)
Rim Diameter (inch)
Radial Tire
Aspect Ratio = (Section Height ¸ Section
Width) x 100
Section Width(mm)
Summer Tire

2E-4 TIRES AND WHEELS
COMPONENT LOCATOR
WHEEL AND TIRE
1 Wheel Bolts.................Steel Wheel : 80-120 Nm
..........................Aluminium Wheel : 110-130 Nm
2 Steel Wheel
3 Aluminium Wheel4 Tire
5 Steel Wheel Weight Balance
6 Hub Cap

TIRES AND WHEELS 2E-5
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
WHEELS AND TIRES
Removal & Installation Procedure
1. Inspection of tire
Check tread area for tread surface, crack, damage by nail
in or stones. Replace or repair if necessary.
lReplace the tire if tread-wear indicator of the tread
grooves appears where marked ' '
.
l
The wear limit of snow tire is the same as normal tire
(1.6mm) and indicator location is marked '
¯'.
Limit1.6mm
Standard2.66mm
Standard2.03mm 2. Wear limit.
3. Runout measurement.
lExcessive runout of tires and wheels can cause the
abnormal wear of tire. Using a dial indicator, measure
wheel and tire runout.
lMeasure radial runout at the rim flange and center of
the tire tread area.
lMeasure lateral runout at the tire bead area of the wheel
and tire sidewall.
Notice
If runout is excessive, replace the tire or wheel.

2E-6 TIRES AND WHEELS
4. Tire pressure inspection.
lTire pressure.
lCheck tread contact with road.
Notice
lIf underinflated, tire may come away from the wheel
during rapid steering.
lAn overinflated tire will cause a hard riding and uneven
wear.
Front & Rear
(P235/75R15)2.1kg/cm (30PSI)2
5. Wheel balance.
lBalance weights should be on each side. When the wheel
is out of balance or a tire has been repaired, be sure to
balance the wheel again.
lIf total weight is over 150g, readjust the balance by
reinstalling the tire on the wheel.
lBalance weight should not protrude from the wheel rim
over 3mm.
lFor aluminum wheel, use aluminum wheel balance weight
only.

TIRES AND WHEELS 2E-7
lTo correct unbalance, install equal weights 180° opposite
each other, one on the inside of the wheel and one on
the outside, at the point of unbalance.
lBalance Weight
6. Cautions for installation and removal.
lClean the mounting surfaces of hub and wheel.
lDo not apply grease or oil on the nuts and bolts (It will
cause looseness and poor tightening).
lUsing a jack, lift up the tire about 3cm from the ground.
lTighten nuts in a criss-cross pattern 2-3 times.
10g
0.4oz20g
0.7oz30g
1.10oz40g
1.40oz50g
1.80oz60g
2.1oz
Steel : 80 - 120Nm
Aluminium : 110 - 130NmTighten Torque

M/T
M/T
A/T (MB)
M/T
A/T (BTRA)
M/T
A/T (BTRA)
M/T
A/T (MB)
M/T
A/T (MB)
A/T (BTRA)
M/T
A/T (MB)
A/T (BTRA)
SECTION 3A
FRONT DRIVE AXLE
TABLE OF CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 3A-1
General Specifications . . . . . . . . . . . . . . . . . . 3A-1
Fastener Tightening Specifications . . . . . . . . . 3A-2
Component Locator . . . . . . . . . . . . . . . . . . . 3A-3
Front Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-3
Auto-Locking Hub . . . . . . . . . . . . . . . . . . . . . . 3A-4
Vacuum Circuit . . . . . . . . . . . . . . . . . . . . . . . . 3A-5
Maintenance and Repair . . . . . . . . . . . . . . . 3A-6
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 3A-6
Vacuum Line . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-6
Steering Knuckle and Drive Shaft . . . . . . . . . . 3A-8
Front Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-14
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . . 3A-16
Axle Housing . . . . . . . . . . . . . . . . . . . . . . . . . 3A-16
Application
Drive Shaft Type
Axle Housing Type
Differential Type
Differential Gear
CV Joint
Build - up
Conventional
Hypoid Gear
4.56
4.56
3.73
4.56
5.38
4.27
4.89
4.89
4.55
4.55
4.55
5.86
3.73
3.73
4.89
1.4 L
SAE 80W/90, API GL - 5
Description
661NA
662NA
661LA
662LA
E20
E23
E32 Reduction Ratio
Oil Capacity
Oil Specification

3A-2 FRONT DRIVE AXLE
FASTENER TIGHTENING SPECIFICATIONS
Steering Knuckle and Drive Shaft
Application
Drive Shaft to Front Axle Inner Shaft
Wheel Speed Sensor
Drive Shaft Cover Bolt
Locking Hub Washer Screw
Hub Flange Bolt
Hub NutNlm
25 - 35
85 - 105
50 - 60
2 - 4
70 - 90
15