torque SSANGYONG MUSSO 2003 Service Manual

3C-8 PROPELLER SHAFT
3. Install the bearing cap to the yoke and insert the spider.Install the opposite side cap by tapping with a plastic
hammer. Adjust clearance of the spider pin to be within 0.1 mm and install the snap ring.
4. Align the alignment marks and install the front and rear propeller shaft. Tighten the nuts to the specified torque.
GasolineDiesel

REAR DRIVE AXLE 3D-7
Removal & Installation Procedure
1. Remove the tire.Installation Notice
2. Release the parking brake. Steel Wheel
Aluminum Wheel
Tightening Torque
3. Remove the bolts and the brake caliper.
Installation Notice Be careful not to damage the brake hose.
Tightening Torque 85 - 100 Nm
4. Remove the brake disc. Notice
To remove the disc, install the bolts (M8 x 1.25) into the service hole and uniformly tighten the bolts.
5. Disconnect the parking brake cable.
80 - 120 Nm
110 - 130 Nm

3D-8 REAR DRIVE AXLE
Tightening Torque 50 - 65 Nm
6. Remove the plug from the axle shaft flange and remove theinner shaft mounting nuts. Installation Notice
7. Remove the axle shaft, parking brake lining and back plate assembly.
8. Installation should follow the removal precedure in the reverse order.

REAR DRIVE AXLE 3D-9
AXLE Removal & Installation Procedure
1. Lift up the vehicle and support the frame safely.
2. Remove the axle shaft.
Tightening Torque 150 - 180 Nm
3. Remove the propeller shaft from the rear axle input shaft.
Installation Notice Notice Place alignment marks before removal.
Tightening Torque 81 - 89 Nm
4. Disconnect the parking brake cable and brake hose.
5. Remove the lower arm mounting nuts and remove the lower arm from the axle housing. Installation Notice

3D-10 REAR DRIVE AXLE
6. Separate the lower shock absorber from the axle housing.Installation Notice
7. Remove the upper arm mounting nuts and remove the upper arm form the axle housing. Installation Notice
Tightening Torque 50 - 65 Nm
8. Remove the stabilizer bar. Installation Notice
Tightening Torque 150 - 180 Nm
9. Remove the lateral rod mounting nuts and remove the lateral rod from the axle housing. Installation Notice
Tightening Torque 30 - 45 Nm
10. Lowering the axle housing slowly, remove the coil springs and spring seats.
11. Installation should follow the removal precedure in the reverse order.
Tightening Torque 150 - 180 Nm

3D-12 REAR DRIVE AXLE
Disassembly Procedure
1. Remove the drain plug and drain the oil. Reinstall the drainplug.
2. Remove the axle housing cover. Notice Clean the cover and housing contact surface.
3. Remove the bearing cap bolts and remove the bearing caps. Pull out the differential carrier assembly. Notice Place alignment marks on the bearing cap not to change the caps before removal. When pulling out the differential
carrier assembly, be careful not to damage the axle housing.
4. Disassemble the parts of the differential carrier assembly.
Tightening Torque 28 - 42Nm

REAR DRIVE AXLE 3D-13
5. Remove the drive pinion lock nut. Disassemble the parts ofthe drive pinion.
Assembly Procedure
1. Clean the all parts and check the followings. Check the ring gear and drive pinion for wear or damage.
If damaged, replace it as set.
Check the bearing for sticks, wear, noise or turning
resistance.
Check the side gear, pinion, pinion shaft and thrust
washer for wear or damage.
Check the differential carrier for crack or wear (bearing
contact surface). Check the gear case for crack.
2. Assemble the parts of the drive pinion.
3. Assemble the parts of the differential carrier.
Tightening Torque of The Pinion Lock Nut 240 - 310 Nm
Tightening Torque of The
Ring Gear Bolts 75 - 90 Nm

3D-14 REAR DRIVE AXLE
4. Measure backlash of the side gear and pinion gear.
Specified Value 0 - 0.05 mm
5. Install the differential carrier assembly into the axle housing.
Tightening Torque of The Bearing Cap Bolts 48 - 69 Nm
Notice Be careful no to change the caps. Be sure to keep the original position of the caps.
6. Measure backlash of the drive pinion and ring gear.
7. Install the axle housing cover.
Specified Value 0.13 - 0.20 mm
Tightening Torque 39 - 46 Nm

REAR DRIVE AXLE 3D-17
Inspection
Remove the LSD assembly and check the pre-load torque.
If necessary, replace LSD assembly.
Procedure
1. Fix the right shaft of LSD to the special tool (A).
2. Install the special tool (B) to the left shaft and rotate counterclockwise and check the pre-load torque.
Normal Torque 3.6 - 9.0kgm
Notice
If necessary, replace LSD assembly.

HYDRAULIC BRAKES 4A-7
MAINTENANCE AND REPAIRON-VEHICLE SERVICE
BLEEDING THE BRAKES For Master Cylinder Replacement
1. Add oil after master cylinder replacement.
2. Run the engine and depress the brake pedal several times to build pressure and then keep the pedal fully depressed.
3. Loosen the screws of primary and secondary pipe at the master cylinder outlets to bleed air.
4. Repeat above step No.3 several times until there are no more air bubbles.
5. Bleed air in the system at the hydraulic unit outlet pipe and wheel if pressure building is not enough by depressing the pedal only after above air bleeding.
For Caliper and Brake Hose Replacement
1. Check the oil level from the oil reservoir and refill if necessary.
2. Run the engine and depress the pedal several times to build pressure and then keep the pedal fully depressed.
3. Connect a vinyl tube to the caliper breather and prepare a container to coentain brake oil.
4. Loosen the breather screw until there are no more bubbles.
5. Bleed air in the system at four (4) wheels in order as shown in right figure if pressure building is not enough by depressing the pedal after above air bleeding.
Tightening Torque
9 - 14 NmItem
Front Bleeder Screw
Rear Bleeder Screw
Notice
Do not reuse the bled brake fluid.
Always bleed the air after replacing brake fluid or
master cylinder, caliper, brake hose and pipe.
Always operate in normal order.