SUBARU BAJA 2006 1.G Owners Manual

3-14
Instruments and controls
If the light comes on while driving, it is unnecessary to
stop the vehicle, but avoi
d driving up steep grades or
in stop and go traffic. T Automatic transmission control system warn-
ing
If the light flashes after the engine starts, it may indi-cate that the au tomatic transmission control system is
not working properly. Contact your nearest SUBARU
dealer for service immediately. „ ABS warning light
„ABS (Anti-lock Brake System)
„ Warning light
„ Warning lights
„ ABS
„ Warning lights
„ Anti-lock Brake SystemThe ABS warning light comes on when the ignition
switch is turned to the “ON” position and goes out after
approximatley two seconds.This is an indication that the ABS system is working
properly.
If the warning light behaves as follows, the ABS
system may not work properly.
When the warning light is on, the ABS function
shuts down; however, the conventional brake
system continues to operate normally.y The warning light does not come on when the
ignition switch is turned to the “ON” position. y
The warning light comes on when the ignition
switch is turned to th e “ON” position, but it
does not go out even when the vehicle speed
exceeds approximately 8 mph (12 km/h). y The warning light comes on during driving.
If any of these conditions occur, have the ABS
system repaired at the first available opportuni-
ty by your SUBARU dealer.
NOTE
If the warning light behavior is as described in the
following, the ABS system may be considered nor-
mal. y The warning light comes on right after the en-
gine is started but goes out immediately, remain-
ing off. y The warning light remains on after the engine
has been started, but it goes out when the vehicle
speed reaches approximately 8 mph (12 km/h). y The warning light comes on during driving, but
it goes out immediately and remains off.
When driving with an insufficient battery voltage such
as when the engine is jump started, the ABS warning
light may come on. This is due to the low battery volt-
age and does not indicate a malfunction. When the(U.S.) (Canada)

3-15
Instruments and controls
– CONTINUED –
battery becomes fully charged, the light will go out. „Brake system warning light
„Brake system
„ Warning light
„ Warning lights
„ Brake system
yDriving with the brake system warning light
on is dangerous. This indicates your brake sys-
tem may not be working properly. If the light re-
mains on, have the brakes inspected by a
SUBARU dealer immediately. y If at all in doubt about whether the brakes are
operating properly, do not drive the vehicle.
Have your vehicle towed to the nearest
SUBARU dealer for repair.
This light has the following two functions: T Parking brake warning
The light comes on with the parking brake applied
while the ignition switch is in the “ON” position. It goes
out when the parking brake is fully released. T Brake fluid level warning
This light comes on when the brake fluid level has
dropped to near the “MIN” level of the brake fluid res-
ervoir with the ignition switch in the “ON” position and with the parking brake fully released. If the brake system warning li
ght should come on while
driving (with the parking brake fully released and with
the ignition switch positioned in “ON”), it could be an
indication of leaking of brake fluid or worn brake pads.
If this occurs, immediately stop the vehicle at the near-
est safe place and check the brake fluid level. If the flu-
id level is below the “MIN” mark in the reservoir, do not
drive the vehicle. Have the vehicle towed to the near-
est SUBARU dealer for repair. „ Door ajar warning lights
„Door ajar warning lights
„ Warning lights
„ Door ajarThe specific door ajar warning light comes on if any
door is not fully closed.
Always make sure this light is out before you start to drive. „Switchback door indicator light
„Switchback door indicator lightWhile the ignition switch is in the “ON” position, the
switchback door indicator light comes on when the
switchback door is open.
While the ignition switch is in the “LOCK” or “ACC” po-
sition, the switchback door indicator light flashes for
approximately 20 seconds and goes off when the
switchback door is open.
(U.S.) (Canada)

3-16
Instruments and controls
„
Low fuel warning light
The low fuel warning light comes on when the tank is
nearly empty approximately 2.6 US gal (10.0 liters, or
2.2 Imp gal). It only operates when the ignition switch
is in the “ON” position.
NOTE
This light does not go out unless the tank is re-
plenished up to an internal fuel quantity of approx-
imately 3.7 US gal (14 liters, 3.1 Imp gal).
(Turbo models only)
Promptly put fuel in the tank whenever the low
fuel warning light comes on. Engine misfires as
a result of an empty tank could cause damage
to the engine.
„ All-Wheel Drive warning light
(AT vehicles)
„All-Wheel Drive warning light
„ AWD warning light
„ Warning light s
„ All-Wheel DriveThe All-Wheel Drive warning light comes on when the
ignition switch is turned to the “ON” position and goes
out after approximately two seconds. T
Turbo models
This light flashes if the vehicle is driven with tires of dif-
ferent diameters or with the air pressure excessively
low in any of its tires. T Non-turbo models
This light comes on when All-Wheel Drive is disen-
gaged and the drive mechanism is switched to Front
Wheel Drive for maintenance or similar purposes.
This light flashes if the vehicle is driven with tires of dif-
ferent diameters or with the air pressure excessively
low in any of its tires.
Continued driving with the AWD warning light
flashing can lead to powertrain damage. If the
AWD warning light flashes, promptly park in a
safe place then check whether all four tires are
the same diameter and whether any of the tires
has a puncture or has lost air pressure for
some other reason.

3-17
Instruments and controls
– CONTINUED –
„Security system status indicator
light (if equipped)
This light is found at the bo ttom center of the combina-
tion meter panel.
On vehicles equipped with a security system, it blinks
to show the driver the operational status of the security
system. For detailed informati on, refer to the “Alarm
system” section in chapter 2. „ Selector lever position indicator (AT
vehicles)
„Indicator light
„ Selector lever position
„ Selector leve
„ Position indicator
This indicator shows the position of the selector lever. „
Gear position indicator (Turbo-AT ve-
hicles)
When the selector lever is in the manual gate, this in-
dicator shows the currently selected gear. „ Turn signal indicator lights
„Indicator light
„ Turn signal
„ Turn signal
„ Indicator lightsThese lights show the operation of the turn signal or
lane change signal.
If the indicator lights do not blink or blink rapidly, the
turn signal bulb may be burned out. Replace the bulb
as soon as possible. Refer to the “Replacing bulbs”
section in chapter 11.
UB3025AA
UBS094AA

3-18
Instruments and controls
„
High beam indicator light „
High beam indicator light
„ Indicator light
„ High beamThis light shows that the headlights are in the high
beam mode.
This indicator light also comes on when the headlight
flasher is operated. „Cargo lamp indicator light
„Cargo
„ Lamp indicator light
Do not switch on the cargo lamp while driving
to avoid distracting other drivers.
This indicator light shows that the cargo lamp comes
on. „ Cruise control set indicator light
„Cruise control
„ Set indicator light
TNon-turbo models
The light comes on when vehicle speed has been set. T Turbo models
The cruise set indicator light comes on when the igni-
tion switch is turned to the “ON” position and goes out
after approximately three seconds.
The light comes on when vehicle speed has been set.
NOTE y If you move the cruise control lever or press the
main switch button whil e turning the ignition
switch “ON”, the cruise control function is deacti-
vated and the cruise control set indicator light
flashes. To reactivate the cruise control function,
turn the ignition swit ch back to the “ACC” or
“LOCK” position, and then turn it again to the
“ON” position.y If this indicator light and the “ ” indicator
light flash simultaneously during driving, have the
vehicle checked by your nearest SUBARU dealer.

3-19
Instruments and controls
– CONTINUED –
ClockClock
To set the time, turn the setting knob clockwise to ad-
vance and counterclockwise to retard the time.
To ensure safety, do not attempt to set the time
while driving, as an accident from inadequate
attention to the road could result.
Light control switchLight control switch
To prevent battery discharge resulting from ac-
cidentally leaving your lights on when your ve-
hicle is parked, the light switch operates only
when the ignition switch is in the “ON” posi-
tion. In any other position, the vehicle’s lights
will be out.
If you park your vehicle on a roadside at night,
use the hazard warning flasher to alert the other
drivers.
The light switch operates only when the ignition switch
is in the “ON” position.
UB2013BA

3-20
Instruments and controls
„
Headlights„
Headlights
To turn on the headlights, turn the knob on the end of
the turn signal lever.
first position
Parking lights, instrument panel illumination, tail lights
and license plate light are on.
second position
Headlights, parking lights, instrument panel illumina-
tion, tail lights, and li cense plate light are on. „
High/low beam change (dimmer)
To change from low beam to high beam, push the turn
signal lever forward. When the headlights are on high
beam, the high beam indicator light “ ” on the in-
strument panel is also on.
To switch back to low beam, pull the lever back to the
detent position.
HS3026BAHS3026CA

3-21
Instruments and controls
– CONTINUED –
„Headlight flasher„
Headlight flasher
Do not hold the lever in the flashing position for
more than just a few seconds.
To flash the headlights, pull the lever toward you and
then release it. The high beam will stay on for as long
as you hold the lever. The headlight flasher works
even though the lighting switch is in the “OFF” posi-tion.
When the headlights are on high beam, the high beam indicator light “ ” on the instrument panel also comes on. „
Daytime running light system
„Daytime running light system
The tail lights, parking lights, and side marker
lights are not turned on by the daytime running
light system. The light switch must always be
turned to the “ ” position when it is dark
outside.
The low beam headlights will automatically come on at
reduced brightness when t he engine has started, un-
der the following conditions: y The parking brake is fully released.
y The light switch is in the “OFF” or “ ” position.
HS3026DA

3-22
Instruments and controls
Turn signal leverTurn signal lever
1) Right turn
2) Left turn
To activate the right turn signal, push the turn signal le-
ver up. To activate the left turn signal, push the turn
signal lever down. When the turn is finished, the lever
will return automatically. If the lever does not return af-
ter cornering, return the lever to the neutral position by
hand.
To signal a lane change, push the turn signal lever up
or down slightly and hold it during the lane change.
The turn signal indicator lights will flash in the direction of the turn or lane change. The lever will return auto-
matically to the neutral pos
ition when you release it.
1 2
HS3027BC

3-23
Instruments and controls
– CONTINUED –
Illumination brightness controlIllumination brightness control
1) Brighten
2) Darken
When the lighting switch is in the “ ” or “ ”
position, you can adjust brightness of the instrument
panel illumination for better visibility.
To brighten, turn the cont rol dial counterclockwise.
To darken, turn the control dial clockwise.
Parking light switchParking
Light switch
The parking light switch operates regardless of the ig-
nition switch position.
By pushing the front end of this switch, following lights
will come on.
– Parking lights
– Front and rear side marker lights
– Tail lights
– License plate lights
To turn off, push the rear end of the parking light switch.
Avoid leaving these lights on for a long time because
1
2
HS3028BB
P
HS3029BA