ESP SUZUKI ALTO 2013 7.G Owners Manual

0-3
82PH0-74E
WARRANTY POLICY
Maruti Suzuki India Limited (hereinafter called “Maruti Suzuki”),
warrants that each new Maruti Suzuki vehicle distributed in India
by Maruti Suzuki and sold by an authorised Maruti Suzuki dealer
will be free, under normal use and service, from any defects in
material and workmanship at the time of manufacture SUBJECT
TO THE FOLLOWING TERMS AND CONDITIONS:
(1) Qualification:To qualify for this warranty the vehicle must be delivered by a
Maruti Suzuki authorised dealer and set-up, and serviced by a
Maruti Suzuki authorised dealer / service station.
(2) Term:The term of the warranty shall be twenty-four (24) months or
40,000 kilometers (whichever occurs first) from the date of
invoice to the first owner.
(3) Maruti Suzuki Warranty Obligation:If any defect(s) should be found in a Maruti Suzuki vehicle within
the term stipulated above, Maruti Suzuki’s only obligation is to
repair or replace at its sole discretion any part shown to be defec-
tive, with a new part or the equivalent at no cost to the owner for
parts or labour, when Maruti Suzuki acknowledges that such a
defect is attributable to faulty material or workmanship at the time
of manufacture. The owner is responsible for any repair or replace-
ments which are not covered by this warranty.
(4) Limitation:
This warranty shall not apply to:
(a) Normal maintenance service required other than the three
free services, including without limitation, oil and fluid
changes, headlight aiming, fastener retightening, wheel bal-
ancing, wheel alignment and tyre rotation, cleaning of injec-
tors, adjustments of clutch and valve clearance.
(b) The replacement of normal wear parts including without lim-
itation, bulbs, tyres and tubes, spark plugs, belts, hoses, fil-
ters, wiper blades, brushes, contact points, fuses, clutch
disc, brake shoes, brake pads, cable and all rubber parts
(except oil seal and glass run).
(c) Any vehicle which has been used for competition or racing.
(d) Any repairs or replacement required as a result of accidents
or collision.
(e) Any defects caused by misuse, negligence, abnormal use or
insufficient care.
(f) Any vehicle which has been modified or altered, including
without limitation, the installation of performance accesso-
ries.
(g) Any vehicle on which parts or accessories not approved by
Maruti Suzuki have been used.
(h) Any vehicle which has not been operated in accordance with
the operating instructions in this Owner’s Manual and Ser-
vice Booklet.
(i) Any vehicle which has not received, during the warranty term,
the service inspections prescribed in this Owner’s Manual
and Service Booklet.
(j) Any vehicle which has been assembled, disassembled,
adjusted or repaired by other than an Maruti Suzuki autho-
rised dealer/service station.
(k) Any vehicle which has been used for purposes other than
what it was designed for.
(l) Any damage or deterioration caused by industrial pollution
and bird droppings.

0-4
82PH0-74E
(m) Insignificant defects which do not affect the function of the
vehicle including without limitation, sound, vibration and fluid
seep.
(n) Any natural wear and tear including without limitation, aging
etc.
(o) Installation and usage of domestic LPG gas/LPG Cylinder.
(p) V-belts, hoses and gas leaks.
(q) Any vehicle retrofitted with LPG/CNG kits.
(5) Extent of Warranty:This warranty is the entire written warranty given by Maruti Suzuki
for Maruti Suzuki vehicles and no dealer or its or his agent or
employee is authorised to extend or enlarge this warranty and no
dealer or its or his agent or employee is authorised to make any
oral warranty on Maruti Suzuki’s behalf.
Maruti Suzuki reserves the right to add any improvements or
change the design of any model at any time with no obligation to
make the same changes on units previously sold.
(6) Warranty Service:To obtain warranty service, the complete vehicle must be pre-
sented at the owner’s expenses to any authorised Maruti Suzuki
workshop.
(7) Owner’s Warranty Responsibilities:It is responsibility of each owner to:
– Make certain that the PDl card was completed at the time of
delivery of the vehicle;
– Have performed, at his own expenses, by an Maruti Suzuki
authorised dealer/service station all the service inspections
specified in the Maruti Suzuki “Owner’s Manual and Service
Booklet and maintain adequate proof that such service
inspections have been performed.– Make certain that the Maruti Suzuki authorised dealer/ser-
vice station performing the service inspection has certified
the work on the “Maintenance Service Record” page in the
“Owner’s Manual and Service Booklet and
– Present the Maruti Suzuki “Owner’s Manual and Service
Booklet to the authorised Maruti Suzuki dealer whenever
requesting service inspections or warranty service.
If the “Owner’s Manual and Service Booklet should be lost or
destroyed the owner should consult the authorised Maruti Suzuki
dealer from whom the vehicle was purchased for instructions con-
cerning replacement of the “Owner’s Manual and Service Book-
let”.
(8) Disclaimer of Consequential Damage:Maruti Suzuki assumes no responsibility for loss of vehicle, loss of
time, inconvenience or any other indirect incidental or consequen-
tial damage resulting from the vehicle not being available to the
owner because of any defect covered by this warranty.
(9) Change of OwnerEven if ownership of the vehicle changes, the remaining warranty
period is effective for the new owner.

0-5
82PH0-74E
EMISSION WARRANTY POLICY
Maruti Suzuki offers the Emission Warranty on all Maruti Suzuki
vehicles (apart from the Regular Warranty and will run parallel to
the regular product warranty) only in four metropolitan cities (New
Delhi, Kolkata, Mumbai and Chennai) with effect from July 1st,
2001.
Terms:The Emission Warranty will be applicable for 80,000 kms or 3
years (Whichever comes earlier) from the date of invoice to the
first owner. The remaining warranty terms will be valid in case of
any change in ownership provided the production of all valid docu-
ments.
Conditions:1. Under Emission Warranty, Warranty claims will be admitted for
a prima facie examination, in case vehicle fails to meet the
Emission Standard as specified in sub rule (2) of rule no. 115
of Central Motor Vehicles Rules (CMVR), 1989.
2. The warranty claims will only be accepted after examination
carried out by Maruti Suzuki or it’s dealer which leads to firm
conclusions that the
a) Original settings have not been tampered in any case.
b) Part (as given in Annexure - A) has a manufacturing defect.
c) Vehicle is unable to meet the Emission Standards (as given
in 1.), inspite of the vehicle having been maintained and
used in accordance with the instructions as specified in
Owner’s Manual and Service Booklet and the used fuel and
different oils (Engine oil, Transmission oil, Brake oil etc.) are
also as per specification. 3. The method of examination for deciding the warranty of the
parts will be at the sole discretion of Maruti Suzuki and it’s
dealer and results of the examination will be final and binding.
If after examination, the warrantable condition is not estab-
lished, Maruti Suzuki and it’s dealer has the right to charge all,
or part of the cost of such examination.
4. Under Emission Warranty, the parts (as given in Annexure - A)
will be changed free of cost, but the consumables will be
charged as per actual.
5. If the part covered under Emission Warranty or the associated
parts, are not independently replaceable, on account of these
being integral parts of a complete assembly, Maruti Suzuki and
it’s dealer will have the sole discretion to replace either the
entire assembly or by using some of the parts of the system
through suitable repairs or modifications.
6. Any consequential repairs or replacement of parts which may
be found necessary to establish compliance of Emission War-
ranty, will not be considered under warranty, unless the same is
under product warranty. The consumable will be charged as
per actual under such repair or replacement.
7. Maruti Suzuki will not be responsible for the cost of transporta-
tion of the vehicle to the nearest Maruti Suzuki dealer work-
shop or any loss due to non-availability of the vehicle during
the period of lodging of a warranty claim and examination and/
or repair by Maruti Suzuki dealer.
8. Maruti Suzuki will not be responsible for any penalty that may
be charged by statutory authorities on account of failure to
comply with the EMISSION STANDARDS.
9. Emission Warranty will not be affected on the change of owner,
provided all the documents are available.

1-1
FUEL RECOMMENDATION
53MH0-74E
Fuel Recommendation
You must use unleaded gasoline with an
octane number (RON) of 91 or higher.
Gasoline/Ethanol blends
Blends of unleaded gasoline and ethanol
(grain alcohol), also known as gasohol, are
commercially available in some areas.
Blends of this type may be used in your
vehicle if they are no more than 10% etha-
nol. Make sure this gasoline-ethanol blend
has octane ratings no lower than those
recommended for gasoline.
Gasoline/Methanol blends
Blends of unleaded gasoline and methanol
(wood alcohol) are also commercially avail-
able in some areas. DO NOT USE fuels
containing more than 5% methanol under
any circumstances. Fuel system damage
or vehicle performance problems resulting
from the use of such fuels are not the
responsibility of MARUTI SUZUKI and may
not be covered under the New Vehicle
Warranty. Fuels containing 5% or less
methanol may be suitable for use in your
vehicle if they contain cosolvents and cor-
rosion inhibitors.
NOTE:
If you are not satisfied with the driveability
or fuel economy of your vehicle when you
are using a gasoline/alcohol blend, you
should switch back to unleaded gasoline
containing no alcohol.NOTICE
The fuel tank has an air space to
allow for fuel expansion in hot
weather. If you continue to add fuel
after the filler nozzle has automati-
cally shut off or an initial blowback
occurs, the air chamber will become
full. Exposure to heat when fully
fuelled in this manner will result in
leakage due to fuel expansion. To
prevent such fuel leakage, stop filling
after the filler nozzle has automati-
cally shut off, or when using an alter-
native non-automatic system, initial
vent blowback occurs.
NOTICE
Be careful not to spill fuel containing
alcohol while refueling. If fuel is
spilled on the vehicle body, wipe it up
immediately. Fuels containing alco-
hol can cause paint damage, which is
not covered under the New Vehicle
Warranty.

2-5
BEFORE DRIVING
53MH0-74E
Keyless Entry System (if
equipped)
53M-04-010
Keyless EntryYou can lock / unlock all doors simultane-
ously by operating the transmitter near the
vehicle.
To lock all doors, press “LOCK” button
once. All indicator lights will flash once
when doors are locked.
To unlock all doors, press “UNLOCK”
button once. All indicator lights will flash
twice when doors are unlocked.
NOTE:
• The operating distance of the keyless
entry system transmitter is about 20
meters, but this may vary depending on
the condition of transmitter’s battery and
surroundings especially near other
transmitting devices such as radio tow-
ers.
• The door locks cannot be operated with
the transmitter if the ignition key is
inserted in the key cylinder or if any door
is open.
• Be sure to close the doors and windows
before locking.• If you lose any of the transmitters (keys),
contact your MARUTI SUZUKI autho-
rised dealer as soon as possible for
erasing the transmitter ID from vehicle
controller memory. In case you need a
new transmitter, place an order with your
dealer.
• Key cylinder mentioned in this section is
the key hole mounted on steering col-
umn, where key is inserted to start the
vehicle.
GENERAL FEATURES
Illuminated Entry
When vehicle is unlocked, the room lamp
will turn ON to facilitate illuminated entry
into the vehicle. The room lamp will turn
OFF when the door is closed.
Illuminated Exit
When door is opened to exit the vehicle,
the room lamp will turn ON and will turn
OFF when the door is closed.
Auto Relock
In case of accidental Unlock/Disarm of
vehicle by Key, vehicle will automatically
Lock within 30 sec. without any indication.
Auto relock cycle gets canceled if user
does any of the following operation within
30 sec:
1. Open any door.
2. Insert key in cylinder.
3. Any door is locked/unlocked by door
knob.
Radio Frequency Lock Out
Key Lock/Unlock/Panic will cease to func-
tion when Key is inside Key cylinder.
EXAMPLE
NOTICE
The transmitter is a sensitive elec-
tronic instrument. To avoid damaging
the transmitter:
• Do not expose it to impacts, mois-
ture, dust or high temperature such
as leaving it on the dashboard
under direct sunlight.
• Do not tamper with internal parts.
• Keep the transmitter away from
magnetic objects such as a televi-
sion.

2-34
BEFORE DRIVING
53MH0-74E
Turn Signal Indicators
53M-04-084
When you turn on the left or right turn sig-
nals, the corresponding green arrow on the
instrument panel will flash along with the
respective turn signal lights. When you
turn on the hazard warning switch, both
arrows will flash along with all of the turn
signal lights.
Main Beam (high beam) Indicator
Light
53M-04-085
This indicator comes on when headlight
main beams (high beams) are turned on.
Front Fog Light Switch (if
equipped)
53M-04-086
The front fog light comes on when front fog
light operates.
Speedometer
ALTO 800
Ty p e 1
53M-04-087
Ty p e 2
53MH0238
EXAMPLE
EXAMPLE

4-1
DRIVING TIPS
53MH0-74E
68PHM4001
Running-in Catalytic Converter
80G106
The purpose of the catalytic converter is to
minimize the amount of harmful pollutants
in your vehicle’s exhaust. Use of leaded
fuel in vehicles equipped with catalytic
converters is prohibited, because lead
deactivates the pollutant-reducing compo-
nents of the catalyst system.
The converter is designed to last the life of
the vehicle under normal usage and when
unleaded fuel is used. No special mainte-
nance is required on the converter. How-
ever, it is very important to keep the engine
properly tuned. Engine misfiring, which
can result from an improperly tuned
engine, may cause overheating of the cat-
alyst. This may result in permanent heat
damage to the catalyst and other vehicle
components.
WA R N I N G
• WEAR YOUR SEAT BELTS AT ALL
TIMES. Even though air bags may
be equipped at the front seating
positions, the driver and all pas-
sengers should be properly
restrained at all times, using the
seat belts provided. Refer to the
“Seat Belts and Child Restraint
Systems” section for instructions
on proper use of the seat belts.
• Never drive while under the influ-
ence of alcohol or other drugs.
Alcohol and drugs can seriously
impair your ability to drive safely,
greatly increasing the risk of injury
to yourself and others. You should
also avoid driving when you are
tired, sick, irritated, or under
stress.
NOTICE
The future performance and reliabil-
ity of the engine depends on the care
and restraint exercised during its
early life. It is especially important to
observe the following precautions
during the initial 960 km of vehicle
operation.
• After starting, do not race the
engine. Warm it up gradually.
• Avoid prolonged vehicle operation
at a constant speed. Moving parts
will break in better if you vary your
speed.
• Start off from a stop slowly. Avoid
full throttle starts.
• Avoid hard braking, especially
during the first 320 km of driving.
• Do not drive slowly with the
transaxle in a high gear.
• Drive the vehicle at moderate
engine speeds.
• Do not tow a trailer.
EXAMPLE

4-7
DRIVING TIPS
53MH0-74E
72F08015
9) Do not attempt sharp handling during
high speed driving. You may lose your
control over your vehicle.
10)When overtaking or changing lanes
while driving at a high speed, keep
ample vehicle-to-vehicle distance.
Braking
72F08011
1) Use the parking brake when parking
your vehicle and shift the gear shift
lever into the first gear or reverse gear
position for the sake of safety.
2) Don’t use hand-braking unless unavoid-
able. It causes the vehicle to skid and a
collision may occur. It is especially dan-
gerous when the tyres are worn out as
they skid more.
72F08012
Use foot brake in three stages
1. Warn the vehicle behind you
2. Gradually apply the brake.
3. Bring the vehicle to a halt.
3) When driving downhill, try not to apply
the brake but use the engine brake
effectively. Overuse of the foot-brake
may result in reduction of brake effec-
tiveness.
Long distance driving
1) Be sure to perform safety checks before
starting a trip.
2) Take rest at certain intervals to prevent
an accident which may occur due to
feeling sleepy or tired.

5-29
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
USB device connection
When connecting a USB device, make
sure that the connector is pushed all the
way into the port.
Do not leave the USB device for long
periods of time in places inside the vehi-
cle where the temperature can rise too
high.
Back up any important data beforehand.
We cannot accept responsibility for any
lost data.
It is recommended not to connect a USB
device that contains data files other than
MP3/WMA/AAC format.
We recommend against use of USB
devices that are non-standard shape
such as key chains, mobile phone
accessories, etc. which may damage or
stress the connection between USB
device and Socket terminal.
Always close the USB socket terminal
when not in use, since entry of foreignmaterial, dust, water, conductive liquids
may damage the audio system or USB
device.
Device such as MP3 player/Mobile
phone/digital camera may not be rec-
ognized by the audio system for playing
music.
Recording MP3/WMA/AAC
files on a USB device
Playback or display may not be possible
depending on the type of USB device in
use or the condition of the recording.
Depending on the connected USB mem-
ory, the files may be played in different
order from the order that the files were
stored.
During initialization, the reading time of
USB device may vary depending upon
factors such as file structure, size and
contents other than music files.
When files recorded contains VBR (vari-
able bit rate), during playback, fast-for-
ward or reverse operation are done.
The sound quality of MP3/WMA/AAC
files generally improves with higher bit
rate in order to achieve good sound qual-
ity recording with CBR 9continuous bit
rate) of at least 128kbps is recom-
mended.
Compression formatsMP3
MPEG 1,2 and 2.5 layer III
Bit rate
:– MPEG-1: 32, 44.1, 48 kHz
– MPEG-2: 16, 22.05, 24 kHz
– MPEG-2.5: 8, 12 kHz
– VBR
Sampling frequency:– MPEG-1: 32, 44.1, 48 kHz
– MPEG-2: 16, 22.05, 24 kHz
– MPEG-2.5: 8, 12 kHz
WMA
Supports only v7/8/9, DRM/Professional/
Loseless/Voice are not supported
Bit rate:48, 64, 80, 96, 128, 160, 192
kbps
Sampling frequency:8, 16, 22.05, 32,
44.1 kHz
AAC
MPEG AAC (Compliant with ISO/
IEC14496-12:2003 + iTunes Meta-data
Specification)
Bit rate: up to 320kbps
Sampling frequency:8/11.025/12/16/
22.05/24/32/44.1/48 kHz
Sampling frequency:8/11.025/12/16/
22.05/24/32/44.1/48 kHz
Maximum number of files/folders
Maximum number of files: 65280 (files +
folders)
Maximum number of files in a folder: 256
Maximum depth of tree structure: 8
Maximum number of folders: 255
(Root folder is included.)

5-33
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
Supported iPod“Made for iPod,” and “Made for iPhone,”
mean that an electronic accessory has
been designed to connect specifically to
iPod, or iPhone, respectively, and has
been certified by the developer to meet
Apple performance standards. Apple is not
responsible for the operation of this
device or its compliance with safety and
regulatory standards. Please note that the
use of this accessory with iPod, or iPhone
may affect wireless performance.
iPhone®, iPod®, iPod® classic, iPod®
nano, and iPod® touch are trademarks of
Apple Inc., registered in the U.S. and other
countries. iPod/ iPhone modelsSoftware
Ve r s i o n
iPhone® 5S 7.1.1
iPhone® 5C 7.1.1
iPhone® 5 7.1.1
iPhone® 4S 7.1.1
iPhone® 4 7.1.1
iPod® touch
(5th generation)7.1.1
iPod® touch
(4th generation)6.1.6
iPod® nano
(7th generation)1.0.3
iPod® nano
(6th generation)1.2
iPod® classic 2.0.5