sensor pressure SUZUKI SWIFT 2000 1.G SF310 Service Owner's Manual

6-66 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE
DIAG. FLOW
TABLE”.
2Is there DTC(s) other than fuel system
(DTC P0171 / P0172)?Go to applicable
DTC Diag. Flow
Table.Go to Step 3.
3Check HO2S-1 Output Voltage.
1) Connect scan tool to DLC with ignition switch OFF.
2) Warm up engine to normal operating temperature and keep
it at 2000 r / min. for 60 sec.
3) Repeat racing engine (Repeat depressing accelerator pedal
5 to 6 times continuously and take foot off from pedal to
enrich and enlean A / F mixture). See Fig. 1.
Does HO2S-1 output voltage deflect between below 0.3 V and
over 0.6 V repeatedly?Go to Step 4.Go to DTC
P0130 Diag.
Flow Table
(HO2S-1 circuit
check).
4Check Fuel Pressure (Refer to section 6E1 for details).
1) Release fuel pressure from fuel feed line.
2) Install fuel pressure gauge.
3) Check fuel pressure. See Fig. 2.
With fuel pump operating
and engine at stop : 160 – 210 kPa, 1.6 – 2.1 kg / cm
2,
22.7 – 29.9 psi.
At specified idle speed : 90 – 140 kPa, 0.9 – 1.4 kg / cm
2,
12.8 – 20.0 psi.
Is measured value as specified?
Go to Step 5.Go to Diag. Flow
Table B-3 Fuel
Pressure Check.
5Check Fuel Injectors and Circuit.
1) Turn ignition switch OFF and disconnect fuel injector
connector.
2) Check for proper connection to fuel injector at each terminals.
3) If OK, then check injector resistance. See Fig. 3.
Injector resistance: 0.5 – 1.5 Ω at 20C (68F)Go to Step 6.Check injector
circuit or replace
fuel injector.
4) Connect injector, connector.
5) Check that fuel is injected out in conical shape from fuel
injector when running engine.
6) Check injector for fuel leakage after engine stop.
Fuel leakage: Less than 1 drop / min.
Is check result satisfactory?
6Check EVAP Canister Purge Valve.
1) Disconnect purge hose (1) from EVAP canister.
2) Place finger against the end of disconnected hose.
3) Check that vacuum is not felt there when engine is cool and
running at idle. See Fig. 4.
Is vacuum felt?Check EVAP
control system
(See Section
6E1).Go to Step 7.
7Check intake manifold absolute pressure sensor for
performance (See DTC P0105 Diag. Flow Table).
Is it in good condition?Go to Step 8.Repair or
replace.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-69
Below
specified value DTC DETECTING CONDITION
POSSIBLE CAUSE

Engine under other than high revolution condition

Not on rough road

Engine speed changing rate

Manifold absolute
pressure changing rate

Throttle opening changing rate

Misfire rate per 200 or 1000 engine revolutions (how
much and how often crankshaft revolution speed
changes) is higher than specified value
Engine overheating

Vacuum leaks (air inhaling) from air intake system

Ignition system malfunction (spark plug(s), high-
tension cord(s), ignition coil assembly)

Fuel pressure out of specification

Fuel injector malfunction (clogged or leakage)

Engine compression out of specification

Valve lash (clearance) out of specification

Manifold absolute pressure sensor malfunction

Engine coolant temp. sensor malfunction

PCV valve malfunction

EVAP control system malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester.
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Check vehicle and environmental condition for:
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Ambient temp.: –10C, 14F or higher
–Intake air temp.: 70C, 158F or lower
–Engine coolant temp.: –10 – 11 0C, 14 – 230F
4) Start engine and keep it at idle for 2 min. or more.
5) Check DTC in “DTC” mode and pending DTC in “ON BOARD TEST” or “PENDING DTC” mode.
6) If DTC is not detected at idle, consult usual driving based on information obtained in “Customer complaint analy-
sis” and “Freeze frame data check”.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-71
1. Throttle body
2. Fuel feed hose
GoodNo good1. Injector connector
STEPACTIONYESNO
6Check PCV valve for clogging (See Section 6E1).
Is it in good condition?Go to Step 7.Replace PCV valve.
7Check EVAP Canister Purge Valve for Closing.
1) Disconnect purge hose (1) from EVAP canister.
2) Place finger against the end of disconnected hose.
3) Check that vacuum is not felt there, when engine is
cool and running at idle. See Fig. 5.
Is vacuum felt?Check EVAP
control system
(See Section 6E1).Go to Step 8.
8Check intake manifold pressure sensor for performance
(See Section 6E1).
Is it in good condition?Go to Step 9.Repair or replace.
9Check engine coolant temp. sensor for performance
(See Section 6E1).
Is it in good condition?Go to Step 10.Replace engine
coolant temp.
sensor.
10Check parts or system which can cause engine rough
idle or poor performance.
–Engine compression (See Section 6A).
–Valve lash (See Section 6A).
–Valve timing (Timing belt installation. See Section 6A).
Are they in good condition?Check wire harness
and connection of
ECM (PCM) ground,
ignition system and
fuel injector for
intermittent open
and short.Repair or replace.
Fig. 1 for Step 3 Fig. 2 for Step 3 Fig. 3 for Step 4
Fig. 4 for Step 5 Fig. 5 for Step 7

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-79
Main
fuseMain relay
To other valves
EVAP canister
purge valve
EVAP canister
purge valveSurge
tank
Tank pressure
control valveFuel vapor separator
Fuel filter cap
Fuel
level
sensor
Fuel tank EVAP
canister
DTC P0443 PURGE CONTROL VALVE CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE
Canister Purge control valve circuit is opened
or shorted.
“R/G” circuit open or short

“W/BI” circuit open

Canister purge valve malfunction
DTC CONFIRMATION PROCEDURE
1) Clear DTC with ignition switch ON.
2) Select “DTC” mode on scan tool and check DTC.
INSPECTION
STEPACTIONYESNO
1Check EVAP canister purge valve operation
1) With ignition switch OFF, disconnect coupler
from canister purge valve.
2) Check resistance of EVAP canister purge
valve. See Fig. 1.
Resistance between
two terminals : 30 – 34 Ω at 20C (68F)
Resistance between
terminal and body : 1M Ω or higher
Is it as specified?“R/G” circuit open or
short.Replace EVAP canister
purge valve.

6-92 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Fig. 1 for Step 1
DTC P1450 BAROMETRIC PRESSURE SENSOR LOW / HIGH INPUT
DTC P1451 BAROMETRIC PRESSURE SENSOR PERFORMANCE PROBLEM
WIRING DIAGRAM / CIRCUIT DESCRIPTION
Barometric pressure sensor is installed in ECM (PCM).
DTC DETECTING CONDITION
POSSIBLE CAUSE
DTC P1450:

Barometric pressure: 136 kPa 1025 mmHg or higher, or
33 kPa 250 mmHg or lower
ECM (PCM) (barometric pressure sensor)
malfunction
DTC P1451:

Vehicle stopped.

Engine cranking.

Difference between barometric pressure and intake
manifold absolute pressure is 26 kPa, 200 mmHg or more.
2 driving cycle detection logic, monitoring once / 1 driving.
Manifold absolute pressure sensor and its
circuit malfunction

ECM (PCM) (barometric pressure sensor)
malfunction
DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Turn ignition switch ON for 2 sec., crank engine for 2 sec. and run it at idle for 1 min.
4) Check pending DTC in “ON BOARD TEST” or “PENDING DTC” mode and DTC in “DTC” mode.
INSPECTION
DTC P1450:
Substitute a known-good ECM (PCM) and recheck.
DTC P1451:
NOTE:
Note that atmospheric pressure varies depending on weather conditions as well as altitude.
Take that into consideration when performing these check.
STEP
ACTIONYESNO
11) Connect scan tool to DLC with ignition switch
OFF.
2) Turn ignition switch ON and select “DATA
LIST” mode on scan tool.
3) Check manifold absolute pressure. See Fig. 1.
Is it barometric pressure (approx. 100 kPa,
760 mmHg) at sea level?Substitute a known-
good ECM (PCM) and
recheck.Check intake manifold
pressure sensor and its
circuit.
Go to P0105 DIAG.
FLOW TABLE.

6-1-2 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
DTC P0300 Random Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0301 Cylinder 1 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0302 Cylinder 2 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0303 Cylinder 3 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0304 Cylinder 4 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0335 CKP Sensor Circuit
Malfunction 6-1- 73. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0340 CMP Sensor Circuit
Malfunction 6-1- 75. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0400 EGR Flow Malfunction 6-1- 78. . . .
DTC P0420 Catalyst System
Efficiency Below Threshold 6-1- 81. . . . . . . . . .
DTC P0443 Purge Control Valve Circuit
Malfunction 6-1- 84. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0480 Radiator Fan Control
System Malfunction 6-1- 85. . . . . . . . . . . . . . . . .
DTC P0500 Vehicle Speed Sensor
Malfunction 6-1- 87. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0505 Idle Control System
Malfunction 6-1- 91. . . . . . . . . . . . . . . . . . . . . . . . DTC P0601 Internal Control Module
Memory Check Sum Error 6-1- 93. . . . . . . . . . .
DTC P1450 Barometric Pressure
Sensor Low / High Input 6-1- 94. . . . . . . . . . . . .
DTC P1451 Barometric Pressure Sensor
Performance Problem 6-1- 94. . . . . . . . . . . . . . .
DTC P1500 Engine Starter Signal
Circuit Malfunction 6-1- 96. . . . . . . . . . . . . . . . . .
DTC P1510 ECM (PCM) Back-up
Power Supply Malfunction 6-1- 97. . . . . . . . . . .
Table B-1 Fuel Injector Circuit Check 6-1- 98. . .
Table B-2 Fuel Pump and Its Circuit
Check 6-1- 99. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-3 Fuel Pressure Check 6-1-101. . . . . . . .
Table B-4 A / C Signal Circuits Check 6-1-103. . .
Table B-5 PSP Switch Signal Circuit
Check 6-1-104. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-6 Electric Load Signal Circuit
Check 6-1-105. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-7 Radiator Cooling Fan Control
System Check 6-1-106. . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6-1-108 . . . . . . . . . . . . . . . . . . . . .

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-15
DIAGNOSTIC TROUBLE CODE (DTC) TABLE
NOTE:
1 driving cycle: MIL lights up when DTC is detected in the first driving cycle.
2 driving cycles: MIL lights up when the same DTC is detected also in the next driving cycle after DTC is
detected and stored temporarily in the first driving cycle.
DTC
NO.
DETECTING ITEMDETECTING CONDITION
(DTC will set when detecting:)MIL
P0105Manifold absolute pressure
circuit malfunction
Low pressure-high vacuum-low voltage (or MAP
sensor circuit shorted to ground)
High pressure-low vacuum-high voltage (or MAP
sensor circuit open)
1 driving
cycle
P0110Intake air temp. circuit
malfunctionIntake air temp. circuit low input
Intake air temp. circuit high input1 driving
cycle
P0115Engine coolant temp. circuit
malfunctionEngine coolant temp. circuit low input
Engine coolant temp. circuit high input1 driving
cycle
P0120Throttle position circuit
malfunctionThrottle position circuit low input
Throttle position circuit high input1 driving
cycle
P0121Throttle position circuit
performance problemPoor performance of TP sensor2 driving
cycles
P0130HO2S circuit malfunction
(Sensor-1)
Min. output voltage of HO2S-higher than
specification
Max. output voltage of HO2S-lower than
specification
2 driving
cycles
P0133HO2S circuit slow response
(Sensor-1)Response time of HO2S-1 output voltage between
rich and lean is longer than specification.2 driving
cycles
P0134HO2S circuit no activity detected
(Sensor-1)Output voltage of HO2S-1 fails to go specification.
(or HO2S-1 circuit open or short)2 driving
cycles
P0135HO2S heater circuit malfunction
(Sensor-1)Terminal voltage is lower than specification at heater
OFF or it is higher at heater ON.2 driving
cycles
P0136HO2S circuit malfunction
(Sensor-2)Max. voltage of HO2S-2 is lower than specification
or its min. voltage is higher than specification2 driving
cycles
P0141HO2S heater circuit malfunction
(Sensor-2)Terminal voltage is lower than specification at heater
OFF or it is higher at heater ON. (or heater circuit or
short)2 driving
cycles
P0171Fuel system too lean
Short term fuel trim or total fuel trim (short and long
terms added) is larger than specification for specified
time or longer. (fuel trim toward rich side is large.)2 driving
cycles
P0172Fuel system too rich
Short term fuel trim or total fuel trim (short and long
term added) is smaller than specification for
specified time or longer. (fuel trim toward lean side is
large.)
2 driving
cycles
P0300
P0301
P0302
P0303Random misfire detected
Cylinder 1 misfire detected
Cylinder 2 misfire detected
Cylinder 3 misfire detectedMisfire of such level as to cause damage to three
way catalyst
MIL
flashing
during
misfire
detection
P0304
y
Cylinder 4 misfire detectedMisfire of such level as to deteriorate emission but
not to cause damage to three way catalyst2 driving
cycles

6-1-16 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
DTC
NO.DETECTING ITEMDETECTING CONDITION
(DTC will set when detecting:)MIL
P0335Crankshaft position sensor
circuit malfunctionNo signal for 2 sec. During engine cranking1 driving
cycle
P0340Camshaft position sensor circuit
malfunctionNo signal during engine running1 driving
cycle
P0400Exhaust gas recirculation
flow malfunction detectedExcessive or insufficient EGR flow2 driving
cycles
P0420Catalyst system efficiency below
threshold
Output waveforms of HO2S-1 and HO2S-2 are
similar.
(Time from output voltage change of HO2S-1 to that
of HO2S-2 is shorter than specification.)
2 driving
cycles
P0443Purge control valve circuit
malfunctionPurge control valve circuit is open or shorted to
ground2 driving
cycles
P0480Radiator fan control circuit
malfunctionRadiator cooling fan relay terminal voltage is low
when cooling temp. is lower than specification2 driving
cycles
P0500Vehicle speed sensor
malfunctionNo signal while running in “D” range or during fuel cut
at decelerating2 driving
cycles
P0505Idle control system malfunctionNo closed signal to IAC valve is detected2 driving
cycles
P0601Internal control module memory
check sum errorData write error (or check sum error) when written
into ECM (PCM)1 driving
cycle
P1450Barometric pressure sensor
circuit malfunctionBarometric pressure is lower or higher than
specification. (or sensor malfunction)1 driving
cycle
P1451Barometric pressure sensor
performance problem
Difference between manifold absolute pressure
(MAP sensor value) and barometric pressure
(barometric pressure sensor value) is larger than
specification during cranking.
2 driving
cycles
P1500Starter signal circuit malfunctionStarter signal is not inputted from engine cranking till
its start and after or it is always inputted2 driving
cycles
P1510ECM (PCM) backup power
source malfunctionNo backup power after starting engine1 driving
cycle

6-1-18 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
FAIL-SAFE TABLE
When any of the following DTCs is detected, ECM (PCM) enters fail-safe mode as long as malfunction continues
to exist but that mode is canceled when ECM (PCM) detects normal condition after that.
DTC NO.
DETECTED ITEMFAIL-SAFE OPERATION
P0105Manifold absolute pressure circuit
malfunction

ECM (PCM) uses value determined by throttle
opening and engine speed.

ECM (PCM) stops EGR, EVAP purge and idle air
control.
P0110Intake air temp. circuit malfunctionECM (PCM) controls actuators assuming that
intake air temperature is 20C (68F).
P0115Engine coolant temp. circuit malfunctionECM (PCM) controls actuators assuming that
engine coolant temperature is 80C (176F).
P0120Throttle position circuit malfunctionECM (PCM) controls actuators assuming that
throttle opening is 20.
P0340Camshaft position sensor circuit
malfunctionECM (PCM) controls injection system sequential
injection to synchronous injection.
P0500Vehicle speed sensor malfunctionECM (PCM) stops idle air control.
P1450Barometric pressure sensor low /
high inputECM (PCM) controls actuators assuming that
barometric pressure is 100 kPa (760 mmHg).

6-1-24 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
ConditionPossible CauseReferring Item
Overheating
Inoperative thermostat

Poor water pump performance

Clogged or leaky radiator

Improper engine oil grade

Clogged oil filter or oil strainer

Poor oil pump performance

Faulty radiator fan control system

Dragging brakes

Slipping clutch

Blown cylinder head gasketThermostat in Section 6B
Water pump in Section 6B
Radiator in Section 6B
Engine oil and oil filter change in
Section 0B
Oil pressure check in Section 6A1
Oil pressure check in Section 6A1
Radiator fan control system in
Section 6E2
Trouble diagnosis in Section 5
Trouble diagnosis in Section 7C
Cylinder head in Section 6A1
Poor gasoline
mileageIgnition system out of order

Leaks or loose connection of high-tension cord

Faulty spark plug (improper gap, heavy deposits
and burned electrodes, etc.)
Engine and emission control system out of
order

Malfunctioning EGR valve

High idle speed

Poor performance of TP sensor, ECT sensor or
MAP sensor

Faulty EGR valve

Faulty fuel injector(s)

Faulty ECM (PCM)
Low compression
Others

Poor valve seating

Dragging brakes

Slipping clutch

Thermostat out of order

Improper tire pressure
High-tension cords in Section 6F1
Spark plugs in Section 6F1
EGR system in Section 6E2
Refer to item “Improper engine
idle speed” previously outlined
TP sensor, ECT sensor or MAP
sensor in Section 6E2
EGR system in Section 6E2
Diagnostic Flow Table B-1
Previously outlined
Valves inspection in Section 6A1
Trouble diagnosis in Section 5
Trouble diagnosis in Section 7C
Thermostat in Section 6B
Refer to Section 3F
Excessive engine
oil consumptionOil leakage

Blown cylinder head gasket

Leaky camshaft oil seals
Oil entering combustion chamber

Sticky piston ring

Worn piston and cylinder

Worn piston ring groove and ring

Improper location of piston ring gap

Worn or damaged valve stem seal

Worn valve stem
Cylinder head in Section 6A1
Camshaft in Section 6A1
Piston cleaning in Section 6A1
Pistons and cylinders inspection
in Section 6A1
Pistons inspection in Section 6A1
Pistons assembly in Section 6A1
Valves removal and installation in
Section 6A1
Valves inspection in Section 6A1