TOYOTA LAND CRUISER 1996 J80 Workshop Manual

SA1UQ−01
SA−48
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (see page SA−27).
HINT:
w/ differential lock:
Before installation, check differential lock operation connecting the connector of the actuator to the
connector of the vehicle side.
w/ differential lock:
Before installation, check that the sleeves on work with switching over the differential lock control
switch.
After checking, lock the front differential.
After installation, fill the differential with gear oil (See page SA−27).
w/ differential lock:
After installation, check that the bleeder plug at the point of the bleeder tu\
be (inside of the engine room)
is not damaged or worn.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UR−01
−
SUSPENSION AND AXLE COIL SPRING AND FRONT SHOCK ABSORBER
SA−49
906
Author: Date:
1996 LAND CRUISER (RM451U)
COIL SPRING AND FRONT SHOCK ABSORBER
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1US−01
SA2662
SA2663
R13152
SA−50
−
SUSPENSION AND AXLE COIL SPRING AND FRONT SHOCK ABSORBER
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE FRONT WHEEL Torque:
Steel wheel: 147 N·m (1,500 kgf·cm, 109 ft·lbf)
Aluminum wheel: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
2. REMOVE FRONT SHOCK ABSORBER
(a) Jack up and support the axle housing.
(b) Hold the piston rod and remove the upper mounting nut. Torque: 69 N·m (700 kgf·cm, 51 ft·lbf)
(c) Hold the shock absorber and remove the lower mounting nut, shock absorber, cushions and retainers.
Torque: 69 N·m (700 kgf·cm, 51 ft·lbf)
3. DISCONNECT STABILIZER BAR FROM AXLE HOUS- ING (See page SA−60 )
4. REMOVE COIL SPRING
(a) Jack down and support axle housing.
(b) Using SST, compress the coil spring. SST 09727−30021
NOTICE:
Do not use an impact wrench. It will damage the SST.
(c) Remove the coil spring.
HINT:
Align the coil spring end with the lower seat and install the coil
spring.
5. REMOVE FOLLOW SPRING
Remove the 2 nuts and follow spring. Torque: 9.2 N·m (94 kgf·cm, 82 in.·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UT−01
FA0530
−
SUSPENSION AND AXLE COIL SPRING AND FRONT SHOCK ABSORBER
SA−51
1996 LAND CRUISER (RM451U)
INSPECTION
INSPECT SHOCK ABSORBER
Compress and extend the shock absorber rod and check that
there is abnormal resistance or unusual operation sounds.
If there is any abnormality, replace the shock absorber with a
new one.
NOTICE:
When discarding the shock absorber, use the following
procedure.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UU−01
SA2667
50 mm
(1.97 in.)30 mm
(1.18 in.)
SA−52
−
SUSPENSION AND AXLE COIL SPRING AND FRONT SHOCK ABSORBER
1996 LAND CRUISER (RM451U)
DISPOSAL
DISCARD SHOCK ABSORBER
Before discarding the shock absorber, drill a hole 2 − 3 mm
(0.079 − 0.118 in.) in diameter at the location shown in the il-
lustration to release the gas inside.
NOTICE:
When drilling, chips may fly out, work carefully. The gas is
colorless, odorless and non −poisonous.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UV−01
−
SUSPENSION AND AXLE COIL SPRING AND FRONT SHOCK ABSORBER
SA−53
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page SA−50 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UW−01
SA2675
SA2676
SA−54
−
SUSPENSION AND AXLE FRONT LATERAL CONTROL ROD
911
Author: Date:
1996 LAND CRUISER (RM451U)
FRONT LATERAL CONTROL ROD
REMOVAL
1. REMOVE FRONT WHEEL
Torque:
Steel wheel: 147 N·m (1,500 kgf·cm, 109 ft·lbf)
Aluminum wheel: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
2. DISCONNECT LA TERAL CONTROL ROD FROM AXLE
HOUSING
Remove the bolt and disconnect the lateral control rod from the
axle housing.
Torque: 171 N·m (1,750 kgf·cm, 127 ft·lbf)
HINT:
After stabilizing the suspension, torque the bolt.
3. REMOVE LATERAL CONTROL ROD FROM FRAME
Remove the nut, bolt and lateral control rod. Torque: 171 N·m (1,750 kgf·cm, 127 ft·lbf)
HINT:
After stabilizing the suspension, torque the bolt.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UX−01
FA0533
SST
SST
FA0534
SST
SST
−
SUSPENSION AND AXLE FRONT LATERAL CONTROL ROD
SA−55
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. REMOVE BUSHING
Using SST, remove the bushing from the lateral control rod.
SST 09710 −22042 (09710 −02051, 09710 −02071),
09950 −70010 (09951 −07150)
2. INSTALL BUSHING
Using SST, install a new bushing into the lateral control rod. SST 09710−22042 (09710 −02051, 09710−02071)
HINT:
Do not use a lubricant when pressing in the bushing.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UY−01
SA−56
−
SUSPENSION AND AXLE FRONT LATERAL CONTROL ROD
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page SA−54 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UZ−01
SA2677
SA2678
−
SUSPENSION AND AXLE FRONT LEADING ARM
SA−57
914
Author: Date:
1996 LAND CRUISER (RM451U)
FRONT LEADING ARM
REMOVAL
1. REMOVE FRONT WHEEL
Torque:
Steel wheel: 147 N·m (1,500 kgf·cm, 109 ft·lbf)
Aluminum wheel: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
2. REMOVE LEADING ARM
(a) Remove the bolt, plate washer and nut from the leading arm to the frame side.
Torque: 177 N·m (1,800 kgf·cm, 130 ft·lbf)
HINT:
After stabilizing the suspension, torque the bolt.
(b) Remove the 2 bolts and nuts from the leading arm to the axle housing side.
Torque: 171 N·m (1,750 kgf·cm, 127 ft·lbf)
HINT:
After stabilizing the suspension, torque the bolts.
(c) Remove the leading arm.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010