Position TOYOTA LAND CRUISER 1996 J80 User Guide

AC2QB−01
Z04523
AC−14
−
AIR CONDITIONING AIR CONDITIONING SYSTEM
1996 LAND CRUISER (RM451U)
POSITIONING
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2QS−01
Z17942
Hose ”A”Hose ”B”
Z17943
Hose Clip
Heater
Radiator Pope Paint Mark
Water Hose Hose ”A”Upper
FR
RH Hose ”B”
RH
FR
Marking 45 ± 10° 45
°
10 °
N06494
AC−28
−
AIR CONDITIONING HEATER UNIT
1355
Author: Date:
1996 LAND CRUISER (RM451U)
HEATER UNIT
REMOVAL
1. REMOVE COOLING UNIT (See page AC−24)
2. DRAIN ENGINE COOLANT FROM RADIATOR
HINT:
It is not necessary to drain out all the coolant.
3. DISCONNECT WATER HOSES FROM HEATER RA- DIATOR PIPES
(a) Grip the claws of the hose clip with pliers and slide the clip
along the hose to a place where it does not clamp the
hose to the pipe.
(b) Disconnect the water hoses.
HINT:
Push the water hose onto the heater radiator pipe as far
as the ridge on the pipe.
Install the hose clip in a position, as shown in the illustra-
tion.
4. REMOVE PIPE GROMMETS
5. REMOVE INSTRUMENT PANEL SAFETY PAD (See page BO−76 )
6. REMOVE INSTRUMENT PANEL REINFORCEMENT
(See page BO−76 )
7. REMOVE HEATER UNIT
(a) Remove the 3 screws and defroster nozzle.(...~---------I I
I II II I
I II IIIv-
N02485
N18179N18181
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2RU−01
Z17944
Hose ”A”
Hose ”B”
Z19353
Hose Clip
Heater
Radiator
Pipe Paint
Water Hose Upper Upper
Fr RH
Marking Hose ”A”
Hose ”B”
45°
AC−48
−
AIR CONDITIONING WATER VALVE
1375
Author: Date:
1996 LAND CRUISER (RM451U)
WATER VALVE
REMOVAL
1. DRAIN ENGINE COOLANT FROM RADIATOR
HINT:
It is not necessary to drain out all the coolant.
2. DISCONNECT WATER VALVE CONTROL CABLE
3. DISCONNECT WATER HOSES FROM HEATER RA-
DIATOR PIPE AND WATER VALVE
(a) Grip the claws of the hose clip with pliers and slide the clip
along the hose to a place where it does not clamp the
hose to the pipe.
(b) Disconnect the water hoses.
HINT:
ATt the time of installation, refer to the following procedure.
Push the water hose onto the heater radiator pipe as far
as ridge on the pipe.
Install the hose clip in a position, as shown in the illustra-
tion.
4. REMOVE WIRE HARNESS PROTECTOR
5. REMOVE WATER VALVE
Remove the 2 bolts and water valve.
N02485N18180N18181
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2RW−01
N14296
−
AIR CONDITIONING WATER VALVE
AC−49
1996 LAND CRUISER (RM451U)
ADJUSTMENT
ADJUST WATER VALVE CONTROL CABLE
(a) Set the vehicle in these conditions.
Ignition switch on.
Blower speed control switch on.
Temperature control switch to ”COOL” position.
(b) Set the water valve to ”COOL” position, install the control
cable and lock the clamp.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z09805
Connector ”A”Connector ”B”
−
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
AC−71
1996 LAND CRUISER (RM451U)
5. A/C or DEF Switch:
INSPECT INDICATOR LIGHT OPERATION
(a) Connect the positive (+) lead from the battery to terminal
A−9 and the negative ( −) lead to terminal B−18.
(b) Push the A/C or DEF switch button in and check that the indicator light lights up.
(c) Then, connect the positive (+) lead from the battery to ter-
minal A−13 and check that the indicator dims.
If operation is not as specified, replace the A/C control assem-
bly.
6. INSPECT AIR INLET CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
FRESHA8 − A19Continuity
RECIRCA8 − A18Continuity
If continuity is not as specified, replace the A/C control assem-
bly.
7. INSPECT MODE CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
FACEA14 − B16Continuity
BI−LEVELA12 − B16Continuity
FOOTA7 − B16Continuity
FOOT −DEFB11 − B16Continuity
DEFB4 − B16Continuity
If continuity is not as specified, replace the A/C control assem-
bly.
8. INSPECT BLOWER SPEED CONTROL SWITCH CON-
TINUITY
Switch positionTester connectionSpecified condition
OFFA10 − B16Continuity
LOA1 − B16Continuity
M1B9 − B16Continuity
M2B10 − B16Continuity
HIB13 − B16Continuity
Connector"A"
Connector"B"
Connector"A"
Connector"A"
...-~~IIB1~t•7 ,3 2I
20Itl'17"lIB,,113121110
e-20-2-C
In,•71'fIl';;l1oT~312I1\
[20It..117,,110141131211110II
0-20-2-<:.-18-2-B
AC2726
AC2727
219129
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z04536
AC2SO−04
Z15447
−
AIR CONDITIONING REAR HEATER SWITCH
AC−77
1404
Author: Date:
1996 LAND CRUISER (RM451U)
REAR HEATER SWITCH
INSPECTION
1. REMOVE INSTRUMENT CLUSTER FINISH CENTER
PANEL WITH A/C CONTROL ASSEMBLY
2. REMOVE REAR HEATER SWITCH
3. INSPECT INDICATOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
5 and the negative ( −) lead to terminal 1.
(b) Push each of the rear heater switch knob in and check
that their indicators lights up.
If operation is not as specified, replace the switch.
4. INSPECT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
HI1 − 4Continuity
OFF−No Continuity
LO1 − 2Continuity
Illumination circuit3 − 6Continuity
If continuity is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0SZ−01
V07130
Shift Lever PositionGear PositionParkingC0C1C2B0B1B2B3F0F1F2
Reverse
Neutral 1st
2nd
3rd
O/D
P
R
N
D
2
L
1st
2nd
*1
3rd
1st
*2 2nd
Operating
*1 Down− shift only in the 2 position and 3rd gear −no up− shift.
*2 Down− shift only in the L position and 2nd gear −no up− shift.
O/D Direct
Clutch (C
0)
2nd Coast Brake (B1)
O/D Brake (B
0) Direct
Clutch (C2)
Forward Clutch (C
1)
2nd Brake (B
2)
1st & Reverse
Brake (B
3)
Rear Planetary Carrier
Rear Planetary Ring Gear
Output Shaft
Front & Rear Planetary
Sun Gear
No.2 One−Way
Clutch (F
2)
No.1 One−Way
Clutch (F
1)
Front Planetary
Ring Gear
Front Planetary
Carrier
O/D Planetary
Ring Gear
O/D Planetary
Carrier
O/D Planetary
Sun Gear
Input Shaft
O/D Input Shaft
O/D One−Way
Clutch (F
0)
AT−2
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION SYSTEM
1996 LAND CRUISER (RM451U)
OPERATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0T3−02
Q07388
AT−6
−
AUTOMATIC TRANSMISSION PARK/NEUTRAL POSITION (PNP) SWITCH
790
Author: Date:
1996 LAND CRUISER (RM451U)
PARK/NEUTRAL POSITION (PNP)
SWITCH
ON−VEHICLE REPAIR
1. DISCONNECT 2 OIL COOLER PIPES (See page
AT−16 )
2. DISCONNECT PARK/NEUTRAL POSITION SWITCH CONNECTOR
3. REMOVE PARK/NEUTRAL POSITION SWITCH
(a) Pry off the lock washer and remove the nut.
(b) Remove the bolt and park/neutral position switch.
4. REINSTALL PARK/NEUTRAL POSITION SWITCH
(a) Install the park/neutral position switch and bolt.
(b) Install a new lock plate and the nut. Torque: 6.9 N·m (70 kgf·cm, 61 in.·lbf)
(c) Stake the nut with the lock plate.
(d) Adjust the park/neutral position switch. (See page DI−131 )
5. RECONNECT PARK/NEUTRAL POSITION SWITCH CONNECTOR
6. RECONNECT 2 OIL COOLER PIPES (See page AT−17 )
Adjust the shift lever position. (See page DI−131)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07314
P1P2
P
AT
−14
−
AUTOMATIC TRANSMISSION SHIFT LOCK SYSTEM
1996 LAND CRUISER (RM451U)
3. INSPECT KEY INTERLOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals 7 and 8.
Standard resistance: 12 − 17 Ω
If the resistance is not as specified, replace the solenoid.
4. INSPECT SHIFT LOCK CONTROL SWITCH
Inspect that there is continuity between each terminal.
Shift positionTester condition to
terminal numberSpecified value
P position (Release
button is not pushed)P1 − PContinuity
P position (Release
button is pushed)P1 − P
P2 − PContinuity
R, N, D, 2, L positionP2 − PContinuity
If the continuity is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT−22
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
1996 LAND CRUISER (RM451U)
(i) Remove the 4 bolts and transfer shift lever.
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
(j) Remove the 2 cushions.
6. DISCONNECT THESE CONNECTORS:
No.1 vehicle speed sensor
No.2 vehicle speed sensor
Park/neutral position switch
Solenoid connector
ATF temperature sensor
Center differential lock indicator switch
L4 position switch
Neutral position switch
7. DISCONNECT BLEEDER HOSE FROM TRANSFER
8. REMOVE FRONT AND REAR PROPELLER SHAFT (See page PR−3 )
9. REMOVE OIL FILLER PIPE
(a) Remove the level gauge.
(b) Remove the upper side mounting bolt.
(c) Remove the bolt and filler pipe.
HINT:
At the time of installation, replace the used O −ring with a new
one.
10. LOOSEN 2 OIL COOLER PIPE UNION NUTS
Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010