TOYOTA LAND CRUISER 1998 Factory Repair Manual

BE-108
- BODY ELECTRICALSLIDING ROOF SYSTEM
2481 Author
: Date
:
2004 LAND CRUISER (RM1071U)
If circuit is as specified, replace the relay.

BE0S8-05
I24749
Sliding Roof Control Gear Assembly with ECU
Cowl SId e J/B LH

SUN ROOF Fuse

ECU-IG1 Fuse
Ignition SwitchSliding Roof Control Switch
BE-106
- BODY ELECTRICALSLIDING ROOF SYSTEM
2479 Author
: Date
:
2004 LAND CRUISER (RM1071U)
LOCATION

BE0O9-02
Sliding Roof reverses during close (down) operation.
Start
Mechanical check
Replace sliding roof motor with ECU. Perform forced operation.*
*: Holding the CLOSE/UP (OPEN/DOWN) switch pressed inhibits the jam protection function at approx.
10 sec. after starting the reverse operation.
If the switch remains pressed any longer, the sliding door starts close operation and it stops when
detecting the fully closed position.
CLOSE/UP
(OPEN/DOWN)
SWITCHON
OFF
Close
(Down)
Roof OperationStop Forced Operation Reverse
Stop
Close (Down)
Close Position Approx. 10 sec.
HINT:
At approx. 10 sec. after starting the reverse operation, it is switched to the forced close (down) operation.
- BODY ELECTRICALSLIDING ROOF SYSTEM
BE-105
2478 Author
: Date
:
2004 LAND CRUISER (RM1071U)
SLIDING ROOF SYSTEM
TROUBLESHOOTING

BE2E2-01
I25791
Cowl Side J/B LH

BATT CHARGE FuseEngine Room R/B

TOWING Fuse

TOWING TAIL Fuse
Towing Converter Relay
(Located inside of the quarter trim panel LH)Trailer Socket
BE-200
- BODY ELECTRICALTRAILER TOWING
2573 Author
: Date
:
2004 LAND CRUISER (RM1071U)
TRAILER TOWING
LOCATION

BE01J-17
BE-2
- BODY ELECTRICALTROUBLESHOOTING
2375 Author
: Date
:
2004 LAND CRUISER (RM1071U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH:
This system uses the body control system, so check the body control system before you proceed with trou-
bleshooting (See page DI-1038).
SymptomSuspect AreaSee page
Ignition switch is not set to each position.4. Ignition switch
5. Power source circuitBE-29
-
Ignition key illumination does not light up.
1. Bulb
2. Body ECU
3. Wire Hauness-
DI-1038
-
Key unlock warning system does not operate.
(The buzzer does not sound when the driver's door is opened with
the ignition OFF and key inserted)1. Key Unlock Warning Switch
2. Door Courtesy Switch
3. Wire HarnessBE-29
BE-44
-
Key unlock warning system does not operate.
(The buzzer sounds when the ignition key is in ACC or ON)1. Ignition Switch
2. Wire HarnessBE-29
-
HEADLIGHT AND TAILLIGHT SYSTEM:
This system uses the body control system, so check the body control system before you proceed with trou-
bleshooting (See page DI-1038).
SymptomSuspect AreaSee page
ºAutomatic light control systemº does not operate.
1. Automatic Light Control Sensor
2. Light Control Switch
3. Door Courtesy Switch
4. Wire HarnessBE-32
BE-32
BE-44
-
Auto turn-off system does not operate when the driver's door is
opened.1. Drivers Door Courtesy SwitchBE-44
Auto turn-off system:
Headlight and taillight do not come on.1. Body ECU
2. Wire HarnessDI-1038
-
Auto turn-off system:
Headlight and taillight stay on.1. Body ECU
2. Wire HarnessDI-1038
-
Only one headlight comes on.
1. Daytime Running Light No.3, 4 Relays
2. Body ECU
3. Bulb
4. Wire HarnessBE-32
BE-32
-
-
ºLO-beamº does not light (All).1. Engine Room J/B Relay Circuit
2. Wire HarnessBE-15
-
ºLO-beamº does not light (One side).
1. Bulb
2. H-LP L-LWR Fuse
3. H-LP R-LWR Fuse
4. Wire Harness-
-
-
-
ºHI-beamº does not light (All).
1. Headlight Dimmer Switch
2. Body ECU
3. Wire HarnessBE-32
BE-32
-
ºHI-beamº does not light (One side).
1. Bulb
2. H-LP L-UPR Fuse
3. H-LP R-UPR Fuse
4. Daytime Running Light No.3, 4 Relays
5. Wire Harness-
-
-
BE-32
-
ºFlashº does not light.
1. Headlight Dimmer Switch
2. Body ECU
3. Wire HarnessBE-32
BE-32
-

- BODY ELECTRICALTROUBLESHOOTING
BE-3
2376 Author
: Date
:
2004 LAND CRUISER (RM1071U) Headlight does not come on.
1. Engine Room J/B Relay Circuit
2. Body ECU
3. Daytime Running Light No.3, 4 Relays
4. Headlight Dimmer Switch
5. Light Control Switch
6. Wire Harness
7. BulbBE-15
BE-32
BE-32
BE-32
BE-32
-
-
Headlight does not come on with light control switch in HEAD.1. Light Control Switch
2. Wire HarnessBE-32
-
Headlight does not go out with light control switch in OFF.1. Engine Room J/B Relay Circuit
2. Wire HarnessBE-15
-
Headlight flickers.1. Bulb
2. Wire Harness-
-
Headlight is dark.1. Bulb
2. Wire Harness-
-
Taillight does not come on with light control switch in TAIL.
1. Engine Room J/B Relay Circuit
2. Light Control Switch
3. Wire HarnessBE-15
BE-32
-
Taillight does not go out with light control switch in OFF.
1. Engine Room J/B Relay Circuit
2. Light Control Switch
3. Wire HarnessBE-15
BE-32
-
Headlight does not come on with engine running and light control
switch in OFF.
1. ECU-B1 Fuse
2. ECU-IG1 Fuse
3. Body ECU
4. Daytime Running Light No.3, 4 Relays
5. Generator L Terminal
6. Parking Brake Switch
7. Wire Harness-
-
BE-32
BE-32
CH-10
BE-63
-
FOG LIGHT SYSTEM:
SymptomSuspect AreaSee page
Fog light does not light up with light control SW HEAD
(Headlight is normal.)
1. FOG Fuse
2. Engine Room J/B Relay Circuit
3. Fog Light Switch
4. Wire Harness-
BE-15
BE-37
-
Fog light does not light up with light control SW HEAD
(Headlight does not light).1.*1 Other Parts
2. Wire Harness-
-
Only one light does not light up.1. Bulb
2. Wire Harness-
-
*1: Inspect Headlight System
TURN SIGNAL AND HAZARD WARNING SYSTEM:
SymptomSuspect AreaSee page
ºHazardº and ºTurnº do not light up.
1. ECU-IG2 Fuse
2. TURN HAZ Fuse
3. Ignitioin Switch
4. Turn Signal Flasher Relay
5. Wire Harness-
-
BE-29
BE-40
-
Hazard warning light does not light up.
(Turn is normal)1. Hazard Warning Switch
2. Wire HarnessBE-40
-
Turn signal does not light up.
(Hazard is normal)1. Turn Signal Switch
2. Wire HarnessBE-40
-

BE-4
- BODY ELECTRICALTROUBLESHOOTING
2377 Author
: Date
:
2004 LAND CRUISER (RM1071U) Turn signal does not light up in one direction.
1. Turn Signal Switch
2. Wire HarnessBE-40
-
Only one bulb does not light up.1. Bulb
2. Wire Harness-
-
INTERIOR LIGHT SYSTEM:
This system uses the body control system, so check the body control system before you proceed with trou-
bleshooting(See page DI-1038).
SymptomSuspect AreaSee page
All the lights do not come ON.
1. DOME Fuse
2. Body ECU
3. DOME Relay(Cowl Side J/B LH)-
DI-1038
-
The light does not come ON when the driver's door is opened.1. Driver's Door Courtesy Switch
2. Wire HarnessBE-44
-
The light does not come ON when the passenger's door is
opened.1. Passenger's Door Courtesy Switch
2. Wire HarnessBE-44
-
The light does not come on when the rear-right door is opened.1. Rear-Right Door Courtesy Switch
2. Wire HarnessBE-44
-
The light does not come on when the rear-left door is opened.1. Rear-Left Door Courtesy Switch
2. Wire HarnessBE-44
-
Only one of the bulbs comes ON.1. Bulb-
The illumination does not fade out when all the doors are closed.
1. Courtesy Switch
2. Wire Harness
3. Boby ECUBE-44
-
DI-1038
The illumination does not fade out immediately when the ignition
switch is turned to ACC or ON within 15 seconds after all the
doors are closed.
1. Ignition Switch
2. ACC Fuse
3. ECU-IG1 Fuse
4. Body ECU
5. Wire HarnessBE-29
-
-
DI-1038
-
The illumination does not fade out immediately when all the doors
are locked within 15 seconds after they are closed.1. Door Unlock Detection Switch
2. Wire HarnessBE-88
-
Room light does not light up.
1. Bulb
2. Room Light
3. Rear Personal Light
4. Wire Harness-
BE-44
BE-44
-
Front personal light does not light up.
1. Bulb
2. Front Personal Light
3. Room Light
4. Wire Harness-
BE-44
BE-44
-
Rear Room light does not light up.
1. Bulb
2. Rear Room Light
3. Wire Harness-
BE-44
-
Vanity light does not light up.
1. Bulb
2. Vanity Light
3. Wire Harness-
BE-44
-
Glove compartment light does not light up.
1. Bulb
2. Glove Compartment Courtesy Switch
3. Wire Harness-
BE-44
-
Courtesy light does not light up.
1. Bulb
2. Door Courtesy Switch
3. Wire Harness-
BE-44
-

- BODY ELECTRICALTROUBLESHOOTING
BE-5
2378 Author
: Date
:
2004 LAND CRUISER (RM1071U)
BACK-UP LIGHT SYSTEM:
SymptomSuspect AreaSee page
Back-up Light does not light up.
1. GAUGE2 Fuse
2. Ignition Switch
3. Wire Harness
4. Bulb-
BE-29
-
-
Back-up Light remains always on.1. Park/ Neutral Position Switch
2. Wire HarnessDI-402
-
Only one light does not light up.1. Bulb
2. Wire Harness-
-
STOP LIGHT SYSTEM:
SymptomSuspect AreaSee page
Stop light does not light up.
1. STOP Fuse
2. Stop Light Switch
3. Wire Harness-
BE-50
-
Stop light always lights up.1. Stop Light Switch
2. Wire HarnessBE-50
-
Only one light always lights up.1. Wire Harness-
Only one light does not light up.1. Bulb
2. Wire Harness-
-
WIPER AND WASHER SYSTEM:
SymptomSuspect AreaSee page
Front wiper and washer do not operate.
1. WIPER Fuse
2. Wiper Switch
3. Wiper Motor
4. Wire Harness-
BE-52
BE-52
-
Front wiper does not operate in LO or HI.
1. Wiper Switch
2. Wiper Motor
3. Wire HarnessBE-52
BE-52
-
Front wiper does not operate in INT.
1. Wiper Switch
2. Wiper Motor
3. Wire HarnessBE-52
BE-52
-
Front washer motor does not operate.
1. WASHER Fuse
2. Washer Switch
3. Washer Motor
4. Wire Harness-
BE-52
BE-52
-
Front wiper does not operate when washer switch is ON.
1. WASHER Fuse
2. Washer Switch
3. Wiper Motor
4. Wire Harness-
BE-52
BE-52
-
Rear wiper does not operate.
1. RR WIPER Fuse
2. Rear Wiper Motor
3. Rear Wiper Switch
4. Rear Wiper Relay
5. Wire Harness-
BE-52
BE-52
BE-52
-
Rear wiper does not operate in INT or ON position.
1. Rear Wiper Switch
2. Rear Wiper Relay
3. Wire HarnessBE-52
BE-52
-
Rear wiper does not return to OFF position.1. Rear Wiper Motor
2. Wire HarnessBE-52
-

BE-6
- BODY ELECTRICALTROUBLESHOOTING
2379 Author
: Date
:
2004 LAND CRUISER (RM1071U) Rear washer motor does not operate.
1. Rear Washer Motor
2. Rear Washer Switch
3. Wire HarnessBE-52
BE-52
-
Washer fluid does not operate.1. Washer Hose and Nozzle-
*1: Inspect wiper arm and blade set positions.
COMBINATION METER (Meter Gauges and Illumination):
SymptomSuspect AreaSee page
Tachometer, fuel gauge and engine coolant temperature gauge do
not operate.1. GAUGE2 Fuse
2. Combination Meter
3. Wire Harness-
BE-58
-
Speedometer does not operate.
1. Speed Sensor
2. Combination Meter
3. Wire HarnessBE-63
BE-58
-
Tachometer does not operate.
1. Igniter
2. Combination Meter
3. Wire HarnessIG-1
BE-58
-
Fuel gauge does not operate or is in abnormal operation.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Combination Meter
4. Wire HarnessBE-63
BE-63
BE-58
-
Oil pressure gauge does not operate.
1. Oil Pressure Receiver Gauge
2. Oil Pressure Sender Gauge
3. Combination Meter
4. Wire HarnessBE-63
BE-63
BE-58
-
Voltmeter does not operate.
1. Voltmeter
2. Combination Meter
3. Wire HarnessBE-63
BE-58
-
Engine coolant temperature gauge does not operate or is in ab-
normal operation
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Combination Meter
4. Wire HarnessBE-63
BE-63
BE-58
-
All illumination lights do not light up.1. Light Control Rheostat
2. Wire HarnessBE-63
-
Brightness does not change even when rheostat is turned.1. Bulb
2. Wire Harness-
-
Only one illumination light does not light up.1. Bulb
2. Wire Harness-
-
COMBINATION METER (Warning Light):
SymptomSuspect AreaSee page
Warning lights do not light up. (Except discharge, open door and
SRS)1. GAUGE1 Fuse
2. Combination Meter
3. Wire Harness-
BE-58
-
Fuel level warning light does not light up.
1. LED
2. Combination Meter
3. Fuel Sender Gauge
4. Wire Harness-
BE-58
BE-63
-
ABS warning light does not light up.
1. LED
2. ABS ECU
3. Wire Harness-
DI-502
-

- BODY ELECTRICALTROUBLESHOOTING
BE-7
2380 Author
: Date
:
2004 LAND CRUISER (RM1071U) Seat belt warning light does not light up.
1. LED
2. Seat Belt Buckle Switch
3. Wire Harness
4. Body ECU-
BE-63
BE-63
DI-1038
Discharge warning light does not light up.
1. METER Fuse
2. LED
3. Wire Harness
4. Generator-
-
-
CH-2
Brake warning light does not light up.
1. LED
2. Parking Brake Switch
3. Brake Fluid Level Warning Switch
4. LED Check Relay
5. Combination Meter
6. Wire Harness-
BE-63
BE-63
BE-63
BE-58
-
SRS warning light does not light up.
1. ECU-B2 Fuse
2. LED
3. Airbag Sensor Assembly
4. Combination Meter
5. Wire Harness-
-
DI-690
BE-58
-
Open door warning light does not light up.
1. DOME Fuse
2. LED
3. Door Courtesy Switch
4. Combination Meter
5. Wire Harness-
-
BE-44
BE-58
-
A/T oil temperature warning light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. ECM-
BE-63
BE-58
DI-1
COMBINATION METER (Indicator Light):
SymptomSuspect AreaSee page
Cruise control indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. ECM-
BE-58
-
DI-1
High-beam indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. Headlight System-
BE-58
-
BE-30
Turn indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. Turn Signal and Hazard Warning System-
BE-58
-
BE-39
Shift indicator lights do not light up.
1. LED
2. Combination Meter
3. Park/Neutral Position Switch
4. Wire Harness-
BE-58
-
-
Only one shift indicator does not light up.1. LED
2. Combination Meter-
BE-58
Malfunction indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. ECM-
BE-58
-
DI-1