TOYOTA LAND CRUISER 2012 Owners Manual

541 4-3. Do-it-yourself maintenance
4
Maintenance and care
L/C200_EE (OM60G38E)Under the instrument panel (type A)
FuseAmpereCircuit
1 CIG 15 A Cigarette lighter
2 BK/UP LP 10 A Back-up lights, trailer
3ACC 7.5 AAudio system, parking assist sys-
tem, multi-display assembly, main
body ECU, mirror ECU, smart entry
& start system, clock
4 PANEL 10 AFour-wheel drive system, ashtray,
cigarette lighter, cool box, cruise
control, center differential lock,
multi-display assembly, seat
heater, air conditioning system,
glove box light, emergency flash-
ers, audio system, headlight
cleaner switch, headlight leveling
dial, power heater, driving position
memory system, outside rear view
mirror switches, overhead module,
roll sensing of curtain shield air-
bags off switch, shift lever switch,
steering switches, VSC OFF
switch, console switch, PANEL
RLY

542 4-3. Do-it-yourself maintenance
L/C200_EE (OM60G38E)
5 ECU-IG NO.2 10 AAir conditioning system, heater,
overhead module, ABS, VSC,
steering sensor, yaw rate & G sen-
sor, main body ECU, stoplights,
moon roof, clock, EC mirror
6 WINCH 5 A No circuit
7 A/C IG 10 ACool box, condenser fan, cooler
compressor, rear window and out-
side rear view mirror defoggers, air
conditioning system
8TAIL 15 ATail lights, license plate lights, front
fog lights, rear fog light, trailer, front
position lights
9 WIPER 30 A Windshield wiper
10 WSH 20 A Windshield washer
11 RR WIPER 15 A Rear window wiper and washer
12 4WD 20 A Four-wheel drive system
13 LH-IG 5 AAlternator, seat heater, windshield
wiper de-icer, front seat belt, emer-
gency flasher, shift lever switch
14 ECU-IG NO.1 5 AABS, VSC, tilt and telescopic steer-
ing, gateway ECU, shift lock sys-
tem, parking assist system, cruise
control system, pre-crash safety,
trailer, headlight cleaner, multi-dis-
play assembly, rain-sensing wind-
shield wipers, driving position
memory system, power door lock
system
15 S/ROOF 25 A Moon roof
FuseAmpereCircuit

543 4-3. Do-it-yourself maintenance
4
Maintenance and care
L/C200_EE (OM60G38E)
16 RR DOOR RH 20 A Power windows
17 MIR 15 AMirror ECU, outside rear view mir-
ror defoggers
18 RR DOOR LH 20 A Power windows
19 FR DOOR LH 20 A Power windows
20 FR DOOR RH 20 A Power windows
21 RR FOG 7.5 A Rear fog light
22 A/C 7.5 A Air conditioning system
23 AM1 5 A No circuit
24 TI & TE 15 A Tilt and telescopic steering
25 FR P/SEAT RH 30 A Power seat
26 PWR OUTLET 15 A Power outlet
27 OBD 7.5 A On-Board diagnosis
28 PSB 30 A Pre-crash safety
29 DOOR NO.1 25 A Main body ECU
30 FR P/SEAT LH 30 A Power seat
31 INVERTER 15 A Inverter
FuseAmpereCircuit

544 4-3. Do-it-yourself maintenance
L/C200_EE (OM60G38E)Under the instrument panel (type B)
FuseAmpereCircuit
1 RSF LH 30 A No circuit
2 B/DR CLSR RH 30 A Back door closer
3 B/DR CLSR LH 30 A Back door closer
4 RSF RH 30 A No circuit
5 DOOR DL 15 A Double locking system
6 AHC-B 20 A 4-Wheel AHC
7 TEL 5 A Multimedia
8 TOW BK/UP 7.5 A No circuit
9 AHC-B NO.2 10 A 4-Wheel AHC
10 ECU-IG NO.4 5 A VGRS, 4-Wheel AHC
11 SEAT-A/C FAN 10 A Ventilators
12 SEAT-HTR 20 A Seat heater
13 AFS 5 A No circuit
14 ECU-IG NO.3 5 A Head LP auto leveling
15 STRG HTR 10 A Heated steering system
16 TV 10 A Multi-display assembly

545 4-3. Do-it-yourself maintenance
4
Maintenance and care
L/C200_EE (OM60G38E)
After a fuse is replaced
If the lights do not turn on even after the fuse has been replaced, a bulb
may need replacement. (P. 546)
If the replaced fuse blows again, have the vehicle inspected by any
authorized Toyota dealer or repairer, or another duly qualified and
equipped professional.
If there is an overload in the circuits
The fuses are designed to blow, protecting the wiring harness from damage.
CAUTION
To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failing to do so may cause damage, and possibly a fire or injury.
Never use a fuse of a higher amperage rating than indicated, or use any
other object in place of a fuse.
Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
This can cause extensive damage or even fire.
Do not modify the fuse or the fuse box.
NOTICE
Before replacing fuses
Have the cause of electrical overload determined and repaired by any autho-
rized Toyota dealer or repairer, or another duly qualified and equipped pro-
fessional, as soon as possible.

546
4-3. Do-it-yourself maintenance
L/C200_EE (OM60G38E)
Light bulbs
You may replace the following bulbs yourself. The difficulty level of
replacement varies depending on the bulb. If necessary bulb
replacement seems difficult to perform, contact any authorized
Toyota dealer or repairer, or another duly qualified and equipped
professional.
For more information about replacing other light bulbs, contact any
authorized Toyota dealer or repairer, or another duly qualified and
equipped professional.
Prepare a replacement light bulb
Check the wattage of the light bulb being replaced. (P. 661)
Remove the engine compartment cover
P. 504
Front bulb locations
Front fog light (if equipped)Front turn signal light
Headlight
high beam

547 4-3. Do-it-yourself maintenance
4
Maintenance and care
L/C200_EE (OM60G38E)
Rear bulb locations
Rear fog light Rear turn signal light Back-up light
License plate lights

548 4-3. Do-it-yourself maintenance
L/C200_EE (OM60G38E)
Replacing light bulbs
Headlight high beams
Turn the bulb base counterclock-
wise.
Unplug the connector while
depressing the lock release.
STEP1
ITY43C041
STEP2

549 4-3. Do-it-yourself maintenance
4
Maintenance and care
L/C200_EE (OM60G38E)Replace the light bulb, and install
the bulb base.
Align the 3 tabs on the light bulb
with the mounting, and insert.
Turn and secure the bulb base.
Shake the bulb base gently to
check that it is not loose, turn the
headlights on once and visually
confirm that no light is leaking
through the mounting.
STEP3
STEP4

550 4-3. Do-it-yourself maintenance
L/C200_EE (OM60G38E)Front fog lights (if equipped)
Remove the fender liner bolts,
loose the fender liner nut and
remove the fender liner.
Fender liner bolts
Fender liner nut
Unplug the connector while
depressing the lock release.
Turn the light bulb counterclock-
wise.
STEP1
STEP2
STEP3