TOYOTA SUPRA 1995 Service Repair Manual

7. INSPECT WHEEL ANGLE
Wheel angle
  2JZ±GE 2JZ±GTE
 
 Inside wheel 
 
35°00'
(33°00'~36500') 
 
34°55'
(32555'~35555')
 
 Outside wheel 
 
30°45'
(Reference) 
 
30°35'
(Reference)
If wheel angle differ from the standard specifications, check
to see if the lengths of the left and right tie rods are the same.
HINT: If the tie rods lengths are not equal, the wheel angle
cannot be adjusted properly.
Reinspect the toe±in after adjusting the tie rods lengths. SA±6
± SUSPENSION AND AXLEWHEEL ALIGNMENT

ADJUSTMENT CHART
HOW TO READ ADJUSTMENT CART
(a) Mark on the graph the measurements taken from the vehicle.
Example (2JZ±GE):
Camber: +0°10'
Caster: +4°20'
(b) As shown in the illustration, read from the graph the amounts
by which the front and/or rear cams are to be adjusted.
Amount to turn adjusting cam (by graduation):
Front cam: + (Longer) 1.8
Rear cam: ± (Shorter) 2.2
± SUSPENSION AND AXLEWHEEL ALIGNMENTSA±7

SA±8± SUSPENSION AND AXLEWHEEL ALIGNMENT

REAR WHEEL ALIGNMENT
1. MEASURE VEHICLE HEIGHT
Rear vehicle height
 Engine Tire size Height
 2JZ±GE 245/50ZR16 250 mm (9.84 in.)
 2JZ±GTE 255/40ZR17 251 mm (9.88 in.)
Measuring point:
Measure from the ground to the center of the lower suspen-
sion arm No.2 mounting bolt.
NOTICE: Before inspecting the wheel alignment, adjust
the vehicle height to specification.
If the vehicle height is not to specification, try to adjust it by
pushing down on or lifting the body.
2. INSTALL CAMBER±CASTER±KINGPIN GAUGE OR
ONTO WHEEL ALIGNMENT TESTER
Follow the specific instructions of the equipment manufactur-
er.
3. INSPECT CAMBER
 
 
 
 2JZ±GE 
 2JZ±GTE 
 Camber
 
 ±1°35' + 45'
 
 ±1°30' + 45'
 Left±right error 30' or less 30' or less
4. INSPECT TOE±IN
Toe±in (total):
A+ B: 0.3° + 0.2°
C±D: 3 + 2 mm (0.12 + 0.08 in.)
5. ADJUST CAMBER AND TOE±IN
(a) Measure the length of the lower suspension arm No.1 and
No.2, as shown in the illustration.
Length:
(E±F) or (F±E) should be less 4.0 mm.
If not, adjust the length of the arms by turning the adjusting
cam, as shown, until (E±F) or (F±E) is less than 4.0 mm.
(b) Measure the camber and toe±in.
Specifications
 
 Toe±in 
  A+ B: 0.3° + 0.1°
C±D: 3 + 1 mm (0.12 + 0.04 in.)
 
  Camber (2JZ±GE)
Left±right error 
 ±1°35' + 30'
30' or less
 
  Camber (2JZ±GTE)
Left±right error 
 ±1°30' + 30'
30' or less
If the camber and toe±in are still not within the specification,
adjust the camber and toe±in with the adjusting cam.
± SUSPENSION AND AXLEWHEEL ALIGNMENTSA±9

(c) Remove the bolt and disconnect the parking brake cable
bracket.
(d) Loosen and adjust the No.1 and/or No.2 cams.
(e) Adjust camber and toe±in by turning the No.1 and / or No.2
cams.
(See adjustment chart)
(f) Torque the No.1 and/or No.2 cam nuts.
Torque: 184 NVm (1,880 kgfVcm, 134 ftVlbf)
(g) Connect the parking brake cable bracket with the bolt. SA±10
± SUSPENSION AND AXLEWHEEL ALIGNMENT

ADJUSTMENT CHART
`HOW TO READ ADJUSTMENT CHART
(a) Mark on the graph the measurements taken from the vehicle.
Example (2JZ±GTE):
Camber (LH): ±1°00'
Camber (RH): ±1°30'
Toe±in: OUT 9 mm (0.35 in.)
(b) As shown the illustration, from the graph the amounts by
which the front and/or rear cam are to be adjusted.
Amount to turn adjusting cam (by graduation):
LH Front cam: + (Longer) 1.1
LH Rear cam: + (Longer) 3.0
RH Front cam: ± (Shorter) 1.0
RH Rear cam: + (Longer) 0.9
± SUSPENSION AND AXLEWHEEL ALIGNMENTSA±11

SA±12± SUSPENSION AND AXLEWHEEL ALIGNMENT

FRONT AXLE HUB
PREPARATION
SST (SPECIAL SERVICE TOOLS)
 
 
 
 
 
 
09308±00010 Oil Seal Puller 
 
 
Steering knuckle oil seal
 
 
 
 
 
 
09608±00010 Steering Knuckle Oil Seal
Replacer 
 
 
 
 
 
 
 
 
 
 
09608±35014 Axle Hub & Drive Pinion Bearing
Tool Set 
 
 
 
 
 
 
 
 
 
(09608±06040) Front Hub Inner Bearing Cone
Replacer 
 
 
 
 
 
 
 
 
(09608±06100) Front Hub Outer Bearing Replacer 
 
 
 
 
 
 
(09608±06200) Rear Axle Bearing Replacer 
 
 
 
 
 
 
 
09611±12010 Tie Rod End Puller 
 
 
 
 
 
 
 
 
 
 
09628±10011 Ball Joint Puller 
 
 
 
Hub bolt
 
 
 
 
 
 
09628±62011 Ball Joint Puller 
 
 
 
 
 
 
 
 
09950±40010 Puller B Set 
 
 
± SUSPENSION AND AXLEFRONT AXLE HUBSA±13

RECOMMENDED TOOLS
 
 
 
 
 
 
09905±00013 Snap Ring Pliers. 
 
 
Front axle hub bearing
EQUIPMENT
 
 
Dial indicator 
 
 
 
Torque wrench 
 
SA±14± SUSPENSION AND AXLEFRONT AXLE HUB

FRONT AXLE HUB
COMPONENTS
± SUSPENSION AND AXLEFRONT AXLE HUBSA±15