Timing ASTON MARTIN V8 VANTAGE 2010 User Guide

Engine Structure (03.01)
3-1-24Workshop ManualIssue 4, November 2008
23. Remove RH exhaust camshaft bearing cap retaining
bolts (x10) evenly and in stages (see Figure 10).
Figure 10
24. Note their orientation and markings and remove the RH exhaust camshaft bearing caps.
25. Remove RH exhaust camshaft (see Figure 11).
Figure 11
26. Remove bolts (x2) securing front end of RH cylinder head to cylinder block.
27. Remove bolts (x10), evenly and in stages securing RH cylinder head to cylinder block (see Figure 12).
Figure 12
28. With assistance, remove RH cylinder head assembly.
29. Remove and discard cylinder head gasket.
Installation
1. Thoroughly clean LH and RH cylinder head faces and retaining bolt pockets.
2. Thoroughly clean LH and RH cylinder block faces.
3. Thoroughly clean and dry LH and RH cylinder head retaining bolts.
4. Install new RH cylinder gasket, locate on dowels.
5. With assistance, install RH cylinder head, locate on dowels.
6. Install and torque tighten cylinder head bolts (x12) in the correct sequence.
7. Lubricate camshaft journals , camshaft lobes, bearing
surfaces on cylinder head and bearing caps with clean
engine oil.
8. Install RH exhaust camshaft, install bearing caps (x5) in their original positions.
9. Install bolts (x10) and torque tighten in the sequence specified.
10. Install sprocket retaining Torx bolt in camshaft.
11. Rotate camshaft accordingly and check each valve clearance using feeler gauges.
12. Repeat procedure and install RH intake camshaft.
13. Remove sprocket retaining Torx bolt.
14. Rotate RH intake and exhaust camshafts until timing flats on each camshaft face uppermost.
15. Install tool (303-530) to RH cylinder head to secure camshafts, install and tighten bolts (x3).
16. Install new LH cylinder gasket, locate on dowels.
17. With assistance, install LH cylinder head, locate on dowels.
18. Install and torque tighten cylinder head bolts (x12) in the correct sequence.
19. Lubricate LH exhaust camshaf t journals, camshaft lobes,
bearing surfaces on cylinder head and bearing caps with
clean engine oil.
20. Install LH exhaust camshaft, install bearing caps (x5) in their original positions.
21. Install bolts (x10) and torque tighten in the sequence specified.
22. Install sprocket retaining Torx bolt in LH exhaust camshaft.
23. Rotate LH exhaust camshaft accordingly and check each valve clearance using feeler gauges.
24. Remove sprocket retaining Torx bolt.
25. Install LH intake camshaft (see Workshop Manual procedure 03.09.BV Camshaft - Intake - LH - Renew
With Engine Removed).
26. Install timing chain tensio ning tool (303-532) into RH
exhaust camshaft sprocket.
27. Apply a force to the tool (303-532) in an anti-clockwise direction and torque tighten RH sprocket Torx bolts.
Remove special tool.
28. Connect multiplugs to LH and RH camshaft timing sensors.
A0309258
A0309260
A0310319

Lubrication System (03.02)
Engine (03.00)3-2-2 Workshop Manual Issue 5, Janauary 2010
Specifications
Engine Oil Specification
Maintenance
Oil Pressure Pump to Sump Gasket -
Renew
1. Remove crankshaft timing chain sprocket (refer to Workshop Manual procedure 03.09.AK Sprocket -
Crankshaft - Renew).
2. Install guide pin through lower hole on chain tensioner. 3. Remove bolt that attaches
the oil pressure pump chain
tensioner assembly to engine bedplate (refer to Figure
1).
4. Remove tensioner assembly.
5. Remove bolts (x3) that attach the oil pressure pump to sump.
6. Release chain from oil pres sure pump sprocket, remove
oil pump.
7. Remove and discard oil pressure pump gasket.
Installation
1. Clean oil pressure pump and mating face on sump.
2. Install new gasket to sump, align to dowels (x2).
3. Position oil pressure pump, install chain on pump sprocket.
4. Install oil pressure pump, align to dowels (x2), Install and torque tighten bolts (x3).
5. Install chain tensioner, install and torque tighten bolt, remove guide pin.
6. Install crankshaft timing chain sprocket (refer to Workshop Manual procedure 03.09.AK Sprocket -
Crankshaft - Renew).
Oil Pump Chain - Renew
Removal
1. Remove oil pressure pump gasket (refer to Workshop Manual procedure 03.02.AG Gasket - Oil Pressure
Pump to Sump - Renew)
Engine oil
Europe/Aus/USA Castrol Edge Sport 10W-60
To achieve the required high performance of synthetic
lubricants, do not mi x with mineral oils.
Capacity Europe (Litres)UK
(Pints)USA
(Qts.)
Full System 13 23 11
Service Fill 10 18 9
Torque Figures
DescriptionNmlb/ft
Oil filter 15 - 18 11-13
Sump plug 20 - 26 15-19
Sump bolts 20 - 22 15-16
Oil delivery pump bolts 19 - 23 14-17
Oil scavenger pump bolts 19 - 23 14-17
Oil scavenger filters 11 - 13 8-10
Oil temperature sensor 16 - 24 12-17
Oil pressure switch 11 - 15 8-11
Oil pump tensioner bracket 11 - 13 8-10
10W-60
AuthorityStandard
API SL/CF
ACEA A3/B3/B4
Oil 10W-60 has both API and ACEA and therefore meets
more demanding tests than eith er API or ACEA oils alone.
Repair Operation Time (ROT)
Figure 1
Repair Operation Time (ROT)
ItemCode
Oil Pump Chain-Renew 03.02.AJ
A0302274

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-3
2. Remove bolts (x3) that attach the oil scavenge pump to sump (refer to Figure 1).
3. Remove oil scavenge pump, remove and discard gasket (refer to Figure 2).
4. Release chain from oil pu mp drive sprocket, remove
chain (refer to Figure 3).Installation
1. Clean oil scavenge pump and mating face on sump.
2. Install new oil scavenge pump gasket, align on dowels (x2).
3. Install chain onto oil scavenge pump sprocket.
4. Install oil scavenge pump, align to dowels (x2), Install and torque tighten bolts (x3).
5. Install chain onto oil pump drive sprocket.
6. Install oil pressure pump gasket (refer to Workshop
Manual procedure 03.02.AG Gasket - Oil Pressure
Pump to Sump - Renew).
Oil Sump Pan - Renew
Removal
1. Remove oil sump (refer to Workshop Manual procedure
03.02.BN Pan - Oil Sump - Remove and Reseal).
2. Remove bolt that attach the crankshaft timing sensor, remove sensor (refer to Figure 1).
Figure 1
Figure 2
Figure 3
A0302274
A0302276
Repair Operation Time (ROT)
A0302305

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-5
8. Press out alternator mounting bushes (x2) from sump (refer to Figure 7).
9. Remove dowels (x4) from sump for oil pressure and scavenge pumps location (refer to Figure 8). 10. Remove Torx screws (x2) that attach the oil pump(s)
chain guide, remove chain gu ide (refer to Figure 9).
11. Remove oil plug from sump.
Installation
1. Clean chain guide, oil filter adaptor, filters (x2), sump plug , pump(s) dowels and crankshaft timing sensor.
2. Install alternator bushes.
3. Install oil filter adaptor.
4. Install filters (x2), install oil filter plates (x2), install and
torque tighten Torx screws (x4).
5. Install oil plug.
6. Install oil pump(s) dowels (x4).
7. Clean old sealant from sensor threads (x2).
8. Apply sealant to engine electric coolant temperature sensor threads, install and torque tighten sensor.
9. Apply sealant to oil pressure sensor threads, install and torque tighten sensor.
10. Install oil pump(s) chain guid e, Install and torque tighten
Torx screws (x2).
11. Install crankshaft timing sensor, install and torque tighten bolt.
12. Install oil sump (refer to Workshop Manual procedure 03.02.BN Pan - Oil Sump - Remove and Reseal).
Oil Sump Pan - Remove and Reseal
Removal
1. Remove oil pump(s) drive chain (refer to Workshop Manual procedure 03.02.AJ Chain - Oil Pump - Renew).
Figure 7
Figure 8
A030206C
A0302307
Figure 9
Repair Operation Time (ROT)
A0302307A

Lubrication System (03.02)
Engine (03.00)3-2-6 Workshop Manual Issue 5, Janauary 2010
2. Disconnect multiplug from oi l pressure sensor (refer to
Figure 1).
3. Disconnect multiplug from engine electric coolant
temperature sensor (refer to Figure 2). 4. Disconnect multiplug from
crankshaft timing sensor
(refer to Figure 3).
5. Release harness clips (x6) from sump (refer to Figure 4).
Figure
Figure 2
A030216
A030216A
Figure 3
Figure 4
A030206
A030206B

Lubrication System (03.02)
Engine (03.00)3-2-8 Workshop Manual Issue 5, Janauary 2010
13. Remove bolts (x16) that attach the sump to engine bedplate (refer to Figure 9).
14. Release and remove sump.
Installation
1. Clean old sealant from sump flange and engine bedplate.
2. Ensure that sump flange and mating face on engine bedplate are clean and dry.
3. Apply a continuous 3mm diameter bead of RTV sealant to sump flange as recommended.
4. Ensure that there are no gaps in sealant track.
5. Install sump, install bolts (x16). Do not torque tighten at this stage.
6. Install bolts (x4), sump to torque tube, lightly tighten bolts and then loosen bolts.
7. Torque tighten sump bolts (x16) in the recommended sequence.
8. Torque tighten sump to torque tube bolts (x4).
9. Install A/C compressor mounting bracket, install and torque tighten Torx bolts (x4).
10. Lubricate and install new O-ring seals to oil pipes.
11. Install oil pipes in sump, install and torque tighten bolts (x2)
12. Install compressor, install and torque tighten bolts (x4). 13. Connect multiplug to A/C compressor.
14. Install LH and RH HEGO
sensor multiplug brackets to
sump. Install and torque tighten bolts (x4).
15. Secure harness clips (x6) in sump.
16. Connect multiplug to crankshaft timing sensor.
17. Connect multiplug to engine electric coolant temperature sensor.
18. Connect multiplug to oil pressure sensor.
19. Install oil pump(s) drive chain (refer to Workshop
Manual procedure 03.02.AJ Chain - Oil Pump - Renew).
Oil Cooler - Renew
Removal
1. Raise vehicle on ramp.
2. Remove undertray (refer to Workshop Manual procedure 01.02.NB Undertray - Front - Renew).
3. Remove pipes from oil cooler (position container to catch oil) (refer to Figure).
Figure 1
4. Remove oil cooler from body (bolts x4).
5. Remove duct from oil cooler (bolts x4).
Installation
1. Install duct from to cooler (bolts x4) (torque).
2. Install oil cooler to body (bolts x4) (torque).
3. Install pipes to oil cooler (torque).
4. Install undertray (refer to Workshop Manual procedure 01.02.NB Undertray - Front - Renew).
5. Lower vehicle on ramp.
Figure 9
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
A030206D
Repair Operation Time (ROT)
ItemCode
Oil Cooler - Renew 03.02.BX
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Caution
Make sure that all open ends of oil cooler pipes and oil cooler connections are plugged to prevent dirt or
foreign material entering the lubrication system.

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-15
2. Remove bolt that attach the crankshaft timing sensor, remove sensor (refer to Figure 1).
3. Remove oil pressure sens or (refer to Figure 2).
4. Remove engine electric coolant temperature sensor (refer to Figure 3). 5. Remove Torx screws (x4) that
attach the oil filter plates
(x2) to sump. Remove plates (refer to Figure 4).
6. Install suitable bolt and re move filters (x2) from sump
(refer to Figure 5).
Figure 1
Figure 2
Figure 3
A0302305
A0302306
A0302306A
Figure 4
WA R N I N G
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Figure 5
A0302305A
A0302308

Lubrication System (03.02)
Engine (03.00)3-2-16 Workshop Manual Issue 5, Janauary 2010
7. Remove oil filter adaptor (refer to Figure 6).
8. Press out alternator mounting bushes (x2) from sump (refer to Figure 7). 9. Remove dowels (x4) from
sump for oil pressure and
scavenge pumps location (refer to Figure 8).
10. Remove Torx screws (x2) that attach the oil pump(s)
chain guide, remove chain gu ide (refer to Figure 9).
11. Remove oil plug from sump.
Installation
1. Clean chain guide, oil filter adaptor, filters (x2), sump plug , pump(s) dowels and crankshaft timing sensor.
2. Install alternator bushes.
3. Install oil filter adaptor.
4. Install filters (x2), install oil filter plates (x2), install and
torque tighten Torx screws (x4).
5. Install oil plug.
6. Install oil pump(s) dowels (x4).
7. Clean old sealant from sensor threads (x2).
8. Apply sealant to engine electric coolant temperature sensor threads, install and torque tighten sensor.
9. Apply sealant to oil pressure sensor threads, install and torque tighten sensor.
Figure 6
A030206B
A030206C
Figure 7
Figure 8
Figure 9
A0302307
A0302307

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-17
10. Install oil pump(s) chain guid e, Install and torque tighten
Torx screws (x2).
11. Install crankshaft timing sensor, install and torque
tighten bolt.
12. Install oil sump (refer to Workshop Manual procedure
03.02.CN Pan - Oil Sump - Remove and Reseal With
Engine Removed).
Oil Sump Pan - Remove and Reseal (with
Engine Removed
)
Removal
1. Remove oil pump(s) drive chain (refer to Workshop Manual procedure 03.02.BJ Chain - Oil Pump - Renew
With Engine Removed).
2. Disconnect multiplug from oi l pressure sensor (refer to
Figure 1). 3. Disconnect multiplug from
engine electric coolant
temperature sensor (refer to Figure 2).
4. Disconnect multiplug from crankshaft timing sensor
(refer to Figure 3).
Repair Operation Time (ROT)
A030216
Figure 2
Figure 3
A030216A
A030206

Lubrication System (03.02)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-2-19
11. Remove Torx bolts (x4) that attach the A/C compressor mounting bracket to engine bedplate and sump.
Remove bracket (refer to Figure 7).
12. Remove bolts (x16) that attach the sump to engine bedplate (refer to Figure 8).
13. Release and remove sump.
Installation
1. Clean old sealant from sump flange and engine bedplate.
2. Ensure that sump flange and mating face on engine bedplate are clean and dry.
3. Apply a continuous 3mm diameter bead of RTV sealant to sump flange as recommended.
4. Ensure that there are no gaps in sealant track. 5. Install sump, install and torque tighten bolts (x16) in the
correct sequence.
6. Install A/C compressor mounting bracket, install and torque tighten Torx bolts (x4).
7. Lubricate and install new O-ring seals to oil pipes.
8. Install oil pipes in sump, install and torque tighten bolts (x2)
9. Install compressor, install and torque tighten bolts (x4).
10. Connect multiplug to A/C compressor.
11. Install LH and RH HEGO se nsor multiplug brackets to
sump. Install and torque tighten bolts (x4).
12. Secure harness clips (x6) in sump.
13. Connect multiplug to crankshaft timing sensor.
14. Connect multiplug to engine electric coolant temperature sensor.
15. Connect multiplug to oil pressure sensor.
16. Install oil pump(s) drive chain (refer to Workshop Manual procedure 03.02.BJ Chain - Oil Pump - Renew
With Engine Removed).
Figure 7
Figure 8
A0302303
A030206D