ECU ASTON MARTIN V8 VANTAGE 2010 Service Manual

Seating (01.10)
Body System (01.00)1-7-12 Workshop Manual Issue 4, November 2008
15. Drill out pop rivets from release rod support, and feed harness past rod (see Figure 8).
16. Release harness from clips (x3) and seat cover loop, feed through seat frame (see Figure 9). 17. Disconnect cushion heater
multiplug (see Figure 10).
18. Release cushion cover from frame, feed harness through cover and foam (see Figure 11).
Installation
1. Feed harness through cushion cover and foam, secure cover to frame,
2. Connect cushion heater multiplug.
3. Feed harness through seat frame, secure to clips (x3) and seat cover loop.
4. Feed harness past rod and install pop rivets to release rod support.
5. Install earth header (nut and bolt) and secure harness to clips (x2).
6. Connect lumbar and squab motor multiplugs.
7. Install seat back shell (rivets x4).
8. Connect heater multiplug and install squab foam.
9. Ease cover over foam attach to velcro, secure strip and push through seat.
10. Secure cover to seat back shell.
Figure 8
Figure 9
A0110295A
A0110294
Figure 10
Figure 11
A0110294A
A0110294B

Seating (01.10)
Body System (01.00)
Issue 4, November 2008 Workshop Manual 1-7-13
11. Secure cover to bottom of seat back shell.
12. Secure cover to seat back shell (studs and velcro).
13. Install airbag module (bolt x1) (torque).
14. Install multiplug bracket fixing.
15. Connect airbag multiplu g and secure to bracket.
16. Install lever cover.
17. Install release lever.
18. Install seat 6 way height adjuster (see Workshop Manual procedure 01.10.AE 6 Way Height Adjuster - Inc.
Motors - Renew).
RH/LH Seat Switchpack Assembly -
Renew
Removal
1. Remove instrument panel bezel assembly (see Workshop Manual procedure 01.12.AV Bezel Assembly
- Instrument Panel - Remove for Access and Refit).
2. Remove console panel assembly (see Workshop Manual procedure 01.12.DB Panel Assembly Console - Renew).
3. Remove instrument cluster hood (6 clips)
4. Remove passenger upper ou ter panel assembly (see
Workshop Manual procedure 01.12.AE Panel Assembly
- IP - Upper - Passenger - Renew).
5. Remove passenger panel assembly (4 clips and 4 screws)
6. Remove driver's upper inner panel assembly (5 clips)
7. Remove driver's upper outer panel assembly (4 clips)
8. Remove driver's panel assembly (4 clips and 3 screws)
9. Remove receiver and audio media system panel screws (x4), disconnect multiplugs (x12).
10. Pull back carpet and disconnect seat adjust switch multiplugs (x6), release harness clip (x2)
11. Remove instrument centre panel assembly
12. Remove seat adjust switch (screws x4) (see Figure 1).
Installation
1. Install seat adjust switch.
2. Install instrument centre panel assembly
3. Connect seat adjust switch multiplugs (x6), install
harness clip (x2) and carpet.
4. Install receiver and audio media systems panel (12 multiplugs and 4 screws)
5. Install driver's panel asse mbly (4 clips and 3 screws)
6. Install driver's upper oute r panel assembly (4 clips)
7. Install driver's upper inne r panel assembly (5 clips)
8. Install passenger's panel assembly (4 clips and 4 screws)
9. Install passenger's upper outer panel assembly (see
Workshop Manual procedure 01.12.AE Panel Assembly
- IP - Upper - Passenger - Renew).
10. Install instrument cluster hood (6 clips)
11. Install console panel assemb ly (see Workshop Manual
procedure 01.12.DB Panel Assembly Console - Renew).
12. Install instrument panel be zel assembly (see Workshop
Manual procedure 01.12.AV Bezel Assembly -
Instrument Panel - Remove for Access and Refit).
Lumbar Pump for the Front Seat (From
08MY) - Remove and Install
Remove
1. Remove the applicable front seat (Refer to ’RH/LH Front Seat - Remove and Install’, page 1-7-1).
2. Remove the cover for the squab from the seat (Refer to ’Front Seat Squab Cover Assembly (Each, from 08MY) -
Remove and Install’, page 1-7-3).
3. Move the lumbar inlay to give access.
4. Remove the tape that attaches the air hoses for the bladder into the lumbar inlay.
5. Move the air pump out of the lumbar inlay.
6. Disconnect the air hoses from the pump.
7. Disconnect the electrical connector for the pump.
8. Remove the pump assembly.
Install
1. Connect the the air hose to the pump.
2. Put the air valve in position into the inlay.
3. Connect the electrical connector for the pump.
4. Put the pump into the correct position in the lumbar inlay.
5. Use applicable tape to hold the hoses into the lumbar inlay.
6. Put the lumbar inlay into the correct position.
Repair Operation Time (ROT)
A0110231
Repair Operation Time (ROT)

Glass, Frame and Mechanism (01.11)
Body System (01.00)
May 2007 Workshop Manual 1-8-1
Body System (01.00)
Glass, Frame and Mechanism (01.11)
Description
Power to the door window regulator motor is available when
the ignition switch is at position ‘0’ and is supplied, through
a thermal cut-out, to the left and right window switches. The
switches are double pole earth so that the current through a
window regulator motor may be switched in either direction
to raise or lower the glass.
Frameless doors
To avoid damaging the body seals during door opening, the
door glass must be lowered before the door can be opened.
This function is controlled by the door modules.
The door module senses the rotation of the latch claw as the
door opens, the door module then drives the door window
regulator motor briefly to lower the door glass until it clears
the glass seals. After closing a door, the window regulator
motor operates to raise the door glass to seat against the
body seals.
Specifications
Maintenance
Glass Regulator - Renew
Removal
1. Remove door trimboard assembly (see Workshop Manual procedure 01.05.CB Trimboard Assembly -
Door - Remove for Access and Refit).
2. Remove screws (x4) securi ng switchpack to trimboard
assembly, remove switchpack.
3. Connect switchpack to door cable harness multiplug (x1).
4. With power on raise/lower gl ass to access glass clamping
bolts (x2).
5. Battery isolation switch ‘OFF’. 6. Mark the glass around the rear clamp.
7. Remove clamping bolts (x2)
and lift glass out of door
(see Figure 1).
8. Remove nuts (x4) securing door glass regulator mechanism (see Figure 2).
9. Disconnect multiplug from regulator motor.
WAR NI N G
PUT ON PROTECTIVE GLOVES AND EYE
PROTECTION WHEN YOU HOLD THE GLASS
COMPONENTS.
THE GLASS CAN BREAK EASILY AND CAUSE INJURY.
Torque Figures
DescriptionNm
Regulator mountings 9.0 (M6)
10-15 (M10)
Glass grip screws 5.0 - 6.0
Repair Operation Time (ROT)
WA R N I N G
PUT ON PROTECTIVE GLOVES AND EYE
PROTECTION WHEN YO U HOLD THE GLASS
COMPONENTS.
THE GLASS CAN BREAK EASILY AND CAUSE INJURY.
Figure 1
Figure 2







Glass, Frame and Mechanism (01.11)
Body System (01.00)1-8-2 Workshop Manual May 2007
10. Remove screws (x3) securing regulator motor to door frame (see Figure 3).
11. Carefully remove regula tor mechanism and regulator
motor out through the larger door frame aperture (see
Figure 4).
Installation
1. Install regulator mechanism and motor, install and torque tighten nuts (x4) and screws (x3). 2. Connect multiplug to regulator motor.
3. Fit glass into door and enga
ge the clamping brackets to
the marked position, install clamping bolts and partially
tighten.
4. Battery isolation switch ‘ON’.
5. Raise glass to fully up and adjust alignment, lower fully and check alignment, repeat until alignment is correct,
finally torque tighten clamping bolts (x2).
6. Disconnect switchpack multiplug, install switchpack on trimboard, install and tighten screws (x4).
7. Install door trimboard asse mbly (see Workshop Manual
procedure 01.05.CB Trimboard Assembly - Door -
Remove for Access and Refit).
RH/LH Door Glass - Renew
Removal
1. Remove door trimboard assembly (see Workshop
Manual procedure 01.05.CB Trimboard Assembly -
Door - Remove for Access and Refit).
2. Set glass position to access clamping bolts (x2) through apertures in door frame (see Figure 1).
Figure 3
Figure 4






WAR NI NG
PUT ON PROTECTIVE GLOVES AND EYE
PROTECTION WHEN YOU HOLD THE GLASS COMPONENTS.
THE GLASS CAN BREAK EASILY AND CAUSE INJURY.
Repair Operation Time (ROT)
ItemCode
Door Glass-Renew RH01.11.BA
Door Glass-Renew LH01.11.BC
Figure 1




Glass, Frame and Mechanism (01.11)
Body System (01.00)
May 2007 Workshop Manual 1-8-3
3. Remove clamping bolts (x2) (see Figure 2).
4. Hold glass firmly and lift out of door, place on protective material in a safe place (see Figure 3).Installation
1. Install door glass with front edge into the channel, and position in clamps, install clamping bolts (x2) and lightly
tighten.
2. With power on, raise glass fully up and adjust position, drop glass fully down and readjust, when aligned raise
to access clamping bolts and tighten bolts to
recommended torque. Repeat until aligned.
3. Install door trimboard assembly (see Workshop Manual procedure 01.05.CB Trimbo ard Assembly - Door -
Remove for Access and Refit).
4. Install door trimboard assembly (see Workshop Manual procedure 01.05.CB Trimbo ard Assembly - Door -
Remove for Access and Refit).
Door Glass - Adjust/Reset
1. Open door.
2. Remove interior door handle securing bolts (x2).
3. Remove inner handle trim and disconnect door latch inner cable and remove secu ring bolts for the outer
cable.
4. Remove access plugs (x2), door trimboard.
5. Set glass to position to access clamping bolts (x2) through apertures in the trim panel.
6. Slightly loosen clampbolts (x2), raise glass and align, lower glass and check alignment. Raise and lower until
correct alignment is achieved.
7. Position glass for access to clamp bolts and tighten bolts.
8. Reset upper glass limit.
9. Reset lower glass limit.
Installation
1. Reconnect door latch inner and outer cable, refit inner handle trim.
2. Install door handle.
3. Reset lower glass limit.
4. Install plugs (x2), door trimboard.
Front Windshield - Renew
1. Open bonnet.
Figure 2
WAR NI N G
PUT ON PROTECTIVE GLOVES AND EYE
PROTECTION WHEN YOU HOLD THE GLASS COMPONENTS.
THE GLASS CAN BREAK EASILY AND CAUSE INJURY.
Figure 3






WA R N I N G
PUT ON PROTECTIVE GLOVES AND EYE
PROTECTION WHEN YO U HOLD THE GLASS
COMPONENTS.
THE GLASS CAN BREAK EASILY AND CAUSE INJURY.
Repair Operation Time (ROT)
Repair Operation Time (ROT)

Instrument Panel (IP) (01.12)
Body System (01.00)1-9-2 Workshop Manual Issue 5, January 2010
10. Remove screw/release fir tree securing door seal plate to
A-post (see Figure 3 and Figure 4).
11. Remove LH and RH A-post trim panels.
12. Disconnect fuel filler flap release switch.
13. Disconnect multiplugs (x5) from instrument panel RH side.
14. Disconnect multiplugs (x6) from instrument panel LH side.
15. Release both door seals from body. 16. Remove trim finishers (x4) and screws (x4) (see Figure
5).
17. Remove LH and RH A-post cant rail trim panels (see Figure 6).
18. Remove rear centre console (see Workshop Manual procedure 01.04.BB Cent re Console Rear Renew).
Figure 3
Figure 4
Figure 5
Figure 6

Instrument Panel (IP) (01.12)
Body System (01.00)
Issue 5, January 2010 Workshop Manual 1-9-3
19. Disconnect multiplugs (x8) and remove centre column
switch panel (see Figure 7 and Figure 8).
20. Using special tool, release se lector cable ball joints from
gear lever mechanism.
21. Remove screws (x6) and remove gear lever mechanism. 22. Remove Allen bolts (x4) from securing carpet retaining
plate to bulkhead drivers side (see Figure 9).
23. Pull back footwell carpets and remove bolts (x2) that secure instrument panel to tunnel (see Figure 10).
24. Remove bolt securing heater fan to bulkhead (see Figure 11).
25. Remove steering wheel (see Workshop Manual 11.06.AB Steering Wheel Renew).
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11

Instrument Panel (IP) (01.12)
Body System (01.00)1-9-4 Workshop Manual Issue 5, January 2010
26. Remove screws (x7) from steering column upper and lower shrouds (see Figure 12).
27. Remove lower and upper column shrouds (see Figure
13).
28. Release and remove drivers side lower instrument panel clips (x7) and disconnect air temperature pipe (see
Figure 14).
29. Pull back steering column bulkhead gaiter. 30. Remove and discard pinch bolt from upper column to
intermediate shaft.
31. Disconnect multiplugs (x14 ) from instrument panel to
main body harness.
32. Remove instrument panel upper air vents (x2) (see
Figure 15).
33. Remove screws from instrument panel to bulkhead (x4).
34. Remove bolts securing instru ment panel to both A-posts
(x6).
35. With assistance, position tool (501-F116) to instrument panel (see Figure 16).
36. Attach and tighten brackets (x2) to instrument panel.
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16

Instrument Panel (IP) (01.12)
Body System (01.00)
Issue 5, January 2010 Workshop Manual 1-9-5
37. Manoeuvre and remove inst rument panel sufficient to
gain access to heater hose (see Figure 17).
38. Position container to collect coolant.
39. Release clip and disconne ct hose from heater unit.
40. Disconnect condenser hose from heater unit.
41. Manoeuvre and remove inst rument panel from vehicle
(see Figure 18).
42. Remove container.
Installation
1. With assistance, manoeuvre instrument panel into vehicle.
2. Connect condenser hose to heater unit.
3. Connect hose to heater and secure with clip.
4. With assistance, manoeuvre instrument panel into position aligning upper column to intermediate shaft.
5. Install new upper column pinch bolt (do not torque at this stage).
6. Install bolts (x6) through instrument panel to both A- posts (do not torque at this stage). 7. Install screws (x4) through
instrument panel to bulkhead
(do not torque at this stage).
8. Ensure instrument panel is correctly aligned and tighten screws (x4) and bolts (x6) to correct torque.
9. Loosen and release attachme nts from instrument panel
and with assistance, remove tool (501-F116) from
vehicle.
10. Tighten upper column pinch bolt to correct torque.
11. Install gaiter to bulkhead.
12. Connect multiplugs (x14) fr om instrument panel to main
body harness.
13. Apply adhesive and install instrument panel upper air
vents and secure in clips.
14. Position drivers side lower instrument panel and connect air temperature pipe.
15. Install panel in clips (x7).
16. Install steering column upper and lower shrouds and install and tighten screws (x7).
17. Install steering wheel (see Workshop Manual 11.06.AB Steering Wheel Renew).
18. Install and tighten bolt from heater fan to bulkhead.
19. Install and torque tighten bolts (x2) from instrument panel to tunnel.
20. Install footwell carpet.
21. Install drivers side carpet retaining plate to bulkhead.
22. Install and torque tighten Allen bolts (x4).
23. Install gear lever mechanism and install and tighten screws (x6).
24. Install selector cable ball joints to gear lever mechanism.
25. Install centre column switch panel and connect multiplugs (x8).
26. Install rear centre cons ole (see Workshop Manual
01.04.BB Centre Console Rear Renew).
27. Install LH and RH cant rail trim panels and install and tighten screws (x4).
28. Install trim finishers (x4) and install seals to door aperture.
29. Connect multiplugs (x11) from LH and RH A-post to
instrument panel.
30. Connect fuel filler flap release switch.
31. Install LH and RH A-post trim panels.
32. Install LH and RH A-post door trim plates.
33. Install rivets (x2), insta ll and tighten screws (x2).
34. Install seal to door aperture.
35. Install LH and RH side tread plates and tighten screws (x12).
36. Install LH and RH side tread plate badges and tighten screws (x4).
37. Install RH door (see Workshop Manual 01.03.EA Door Assembly - RH - Remove for Access and Refit).
38. Install RH front seat (see Workshop Manual 01.10.AA Seat Assembly - Front - RH - Remove for Access and
Refit).
Figure 17
Figure 18

Instrument Panel (IP) (01.12)
Body System (01.00)1-9-6 Workshop Manual Issue 5, January 2010
39. Install LH front seat (see Workshop Manual 01.10.AB Seat Assembly - Front - LH - Remove for Access and
Refit).
40. Fill cooling system (see Workshop Manual 03.03.AD
Coolant - Drain and Refill).
41. Re-charge air conditioni ng system (see Workshop
Manual 12.03.FA Tank - Receiver Drier - Renew).
42. Connect vehicle battery.
Airbag Panel and Door Assembly -
Renew
Removal
1. Remove glovebox assembly (see Workshop Manual
procedure 01.12.AL Glovebox Assembly - Renew).
2. Remove glovebox shield (see Figure 1).
3. Remove the bolts (x3) that secure the airbag panel and
door assembly plate to the chassis (see Figure 2)
.
4. Remove airbag panel and d oor assembly (5 clips) (see
Figure3).
Installation
1. Install airbag panel and door assembly (5 clips).
2. Through glovebox aperture, install support right-angled bar and secure bolts (x3).
3. Remove and clean double-sided taped from glovebox shield, apply new tape and install.
4. Install glovebox assembly (see Workshop Manual procedure 01.12.AL Gloveb ox Assembly - Renew).
Glovebox Assembly - Renew
Removal
1. Remove passenger lower panel assembly (5 clips and
multiplug).
2. Remove the securing screws holding the glove box hinge to the chassis (x2).
3. Support the glove box and locate the latch mechanism.
4. Using a suitable tool press the latch mechanism to release the glove box.
5. Support the glove box and detach the buffer cord from the glove box.
Installation
1. Support glovebox and attach the buffer cord (ensure the cord is through correct aperture).
2. Install glovebox into aperture and press top to latch.
3. Align the glovebox hinge an d secure with screws (x2)
including spacers between the hinge and chassis.
4. Install passenger lower panel assembly (5 clips and 1 multiplug).
Repair Operation Time (ROT)
Figure 3
Repair Operation Time (ROT)
ItemCode
Glovebox Assembly-Renew 01.12.AL