coolant AUDI A4 1997 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Owner's Guide

01-199
Display group 017
Note:
If in display group 029, display field 1, the value of the EGR system throughput diagnosis is not set to "0" during the
regeneration of the "readiness code," and/or a malfunction relating to the exhaust system is stored in the DTC memory,
display group 017 is used to carry out a selective diagnosis.
During cold start at idle, -10 C to 30 C (14 to 86 F), and during "Basic Setting" function 04, no exhaust gas recirculation
takes place. Since exhaust gas recirculation is switched off automatically during "Basic Setting" function 04, diagnosis of EGR
throughput is evaluated only in "Read Measuring Value Block." function 08. If diagnostic conditions are fulfilled, the Engine Control Module (ECM) checks the flow through the EGR system after each
start. The diagnostic conditions are only reached during a trip at 80-100 km/h (50-63 mph) in 4th or 5 gear and/or with selector
lever in the "D"position, preferably in 4th gear position. If the diagnostic conditions are fulfilled, the diagnosis is active. In order
to get a diagnostic result, the vehicle must be driven approx. 1-1/2 to 5 minutes under the diagnostic conditions. However, the
diagnosis is only considered OK when the EGR temperature (display field 4) is greater than 50 C (122 F) during the reading
time (display field 2). Diagnosis of the EGR flow (exhaust gas recirculation quantity) is active as soon as the following diagnostic conditions are
fulfilled:

Coolant temperature: greater than 8 C (46 F) ( display group 001) Vehicle speed: constant drive
Engine speed: 2000-3000 RPM ( display group 003) Engine load: 30-60%
Pa
ge 280 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-204
Display group 022
Notes:
Display group 022 should only be considered on vehicles with traction control (ATC).
Vehicles with traction control (ATC) can be recognized by the ATC indicator light in the instrument cluster and/or ABS (ATC)
On Board Diagnostic (OBD).
Repair Manual, Brake System On Board Diagnostic (OBD), Repair Group 01.

The wheel slip information for traction control (ATC) is calculated in the ABS control module. If slip is recognized, the ABS
control module requests a reduction in torque from the Engine Control Module (ECM). This torque reduction is divided into 12
reducing stages.
With a cold engine, coolant temperature less than 20 C (68 F), the reduction of engine torque is obtained:
With retarded ignition timing angle for lower reducing stages (1-5)
By brief shut-off of individual fuel injectors for higher reducing stages (6-12)
If the engine is warm, coolant temperature greater than 40 C (104 F), the engine torque reduction is obtained only by briefly
switching off individual fuel injectors.
Display shows
Display/specified value
Designation
Basic setting 22
1 2 3 4 0 - 12 1 = Reducing stages

_._ crankshaft
2 = Ignition timing point retarded by ATC (only with cold engine)
Pa
ge 287 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-215
Notes on display fields 3 and 4:

Display field 3 evaluates all malfunctions except "Combustion misfiring and oxygen sensor control."
Display field 4 evaluates only the malfunctions "Combustion misfiring and oxygen sensor control"
If a malfunction is recognized, the corresponding counter will be set to "40." The counter is decremented, during a new
start, when the trip was started at coolant temperature of 49 C (120 F) and ended at a water temperature of 71 C
(160 F) and the malfunction is no longer recognized. However, decrementing is only allowed if the MIL has not lit up yet
or is no longer lit. When counter status "0" is reached, the recognized malfunction is erased. If the DTC memory is erased, the counter is also decremented.
Pa
ge 306 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-235
Notes on display field 3 and 4:
Value "0" = Diagnosis condition not fulfilled.
Value "1" = Diagnosis condition fulfilled. X
X
X
X
X
X
X
X
Meaning of 8-digit "Diagnosis condition 1"

1 = Coolant temperature: 70 - 110 C ( display group 001)
2 = Engine load: 27 - 66% ( display group 003)
3 = Engine speed: 1800 - 2700 RPM ( display group 003)
4 = Fuel throughput after engine start
[only fulfilled after approx. 3 min. trip (no idle) after start]

5 = No fuel enrichment
(during diagnosis no enrichment can occur display group 019)
6 = Closed throttle position switch open ( display group 008)
7 = Oxygen sensor control, bank 2 active ( display group 008)
8 = Oxygen sensor control, bank 1 active ( display group 007)
Pa
ge 331 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-241
Notes on display field 3 and 4:
Value "0" = Diagnosis condition not fulfilled
Value "1" = Diagnosis condition fulfilled X
X
X
X
X
X
X
X
Meaning of 8-digit display "Diagnosis condition 1"

1 = Coolant temperature: 70 - 110 C ( display group 001)
2 = Oxygen sensor heating (all four O2S heaters; display group 040)
3 = Momentary constant drive

4 = No fuel enrichment (during diagnosis no enrichment can occur)

5 = Long-term constant drive

6 = Closed throttle position switch open ( display group 002)
7 = Oxygen sensor control, bank 2 active ( display group 008)
8 = Oxygen sensor control, bank 1 active ( display group 007)
Pa
ge 337 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-244
Display group 099 Display
shows Display/specified
value Designation/diagnosis
Basic
setting 99
1 2 3 4 ... RPM 1 = Momentary engine speed Display group 003, display field 1 ...% 2 = Momentary engine load display group 003, display field 2
... C
3 = Coolant temperature display group 001, display field 1

-Control OFF
and/or
-Control ON
4 = Oxygen sensor control OFF in "Basic Setting" function 04; Oxygen sensor control
ON in "Read Measuring Value Block" function 08
Notes on display field 4:

For defined troubleshooting, the oxygen sensor control is switched off when display group 099 is selected under "Basic
Setting" function 04, and switched on when display group 099 is selected under "Read Measuring Value Block"function
08. When leaving "Basic Setting" function 04, oxygen sensor control is automatically active again.
You can switch back and forth between "Basic Setting" function 04 and "Read Measuring Value Block" function 08 by
pressing buttons -4- and -8- on the VAG 1551 scan tool.
Pa
ge 340 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

EGR valve is closed
No coolant temperature correction; fixed value
80 C (176 F)

Learning values are relearned (idle and CO
content are adjusted automatically)
Pa
ge 347 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-261

- Check display fields 1 and 3:

Display
field Designation
Specified
value
1 Coolant
temperature Greater than
70 C
3 Altitude display Less than 48

Note on display field 1:

If the displayed value is less than 70 C, let the
vehicle warm up until at least 70 C coolant
temperature is attained.
Note on display field 3:
If the displayed value is greater than 48
(corresponds to an altitude of approx. 1800 m) a
diagnosis of the exhaust return can not be
conducted due to altitude. Setting the readiness
code at this altitude is not possible.
If specified values are attained Step 3
Pa
ge 360 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1