oil AUDI A4 2000 B5 / 1.G APB Engine Valve Gear Service User Guide

15-13


- Pull out seal with oil seal extractor 2085 and bolt 2085/1.
- Clean contact surface and sealing surface.
Do not apply oil to sealing lip or outer circumference of seal before
installing.
- Install guide sleeve (from tool set 3241) onto camshaft.

Installing
Install in reverse sequence.
Note:
When installing Hall sensor rotor, ensure that locating lug engages in slot
in camshaft. - Press in seal until flush using press sleeve 3241/1 and bolt 3241/3.
Pa
ge 13 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-14

Removing oil seal at Hall sensor (left cylinder
head)

Note:
Leave coolant hoses connected. - Detach coolant reservoir -arrows- and move clear to side.
- Unplug connector from coolant level monitor.
- Move wiring harness clear at bulkhead.

- Unbolt bracket -arrows- for plug connectors on bulkhead and move
clear to side.
Pa
ge 14 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-15

- Unbolt Hall sensor housing (10 Nm).

- Unbolt Hall sensor rotor (20 Nm) and carefully
lever off rotor using a screwdriver.

- Screw in bolt from 2085/1 oil ring extractor.

- Pull out seal with oil seal extractor 2085 and bolt 2085/1.
- Clean contact surface and sealing surface.
Do not apply oil to sealing lip or outer circumference of seal before
installing.
- install guide sleeve (from tool set 3241) onto camshaft.
Pa
ge 15 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-17

Rear oil seal and sealing flange (left cylinder
head)

Note:
Rear sealing flange and oil seal on left-hand
cylinder head must be replaceed together as
follows:

- Remove bolts -arrows- and remove engine cover panels -A...C-.

- Remove air duct -arrows-.
Pa
ge 17 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-19

- Remove cover panel from cylinder head cover
(cylinder bank 4-6).

- Release hose clamp -arrow-.
- Remove upper section of intake line -1-.
- Disconnect hose -2-.

- Disconnect hose (arrow).
- Remove bolt securing toothed belt guard from cylinder head cover.
- Pull plug connectors off ignition coils.
- Pull crankcase breather off cylinder head cover.
- Remove cylinder head cover.
Pa
ge 19 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-20


- Remove double bearing cap -arrows-.
- Take out oil seal and sealing flange.
- Clean contact surfaces and sealing surfaces of double bearing cap.

- Apply a thin coating of sealant 454 300 A2 to shaded areas on double
bearing cap (see illustration), install bearing cap and tighten bolts to 10
Nm.
Pa
ge 20 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-21

- Install guide sleeve (from tool set 3241) onto
camshaft.

Installing
Install in reverse sequence; note the following points: - Press in oil seal until flush using press sleeve 3241/1 and bolt 3241/3.
- Carefully knock in sealing flange against stop using 3202 and a plastic
hammer.

- Seal end points of joints between bearing caps and cylinder head.
- Before installing cylinder head cover and gasket, carefully apply a
small quantity of sealant D 454 300 A2 at four end points of sealing
surfaces on cylinder head -arrows-, using a small screwdriver.
Pa
ge 21 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-24


Installing
Install in reverse sequence; note the following points: - Pull off hose -1-.
- Pull plug connectors off ignition coils.
- Pull crankcase breather off cylinder head cover.
- Remove ignition coils.
- Remove cylinder head cover.

- Seal end points of joints between bearing caps and cylinder head.
- Before installing cylinder head cover and gasket, carefully apply a
small quantity of sealant D 454 300 A2 at four end points of sealing
surfaces on cylinder head -arrows-, using a small screwdriver.
Pa
ge 24 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-28

- Remove bolt securing toothed belt guard from
cylinder head cover.

- Unplug connectors from ignition coils.

- Pull crankcase breather off cylinder head
cover.

- Remove ignition coils.

- Remove cylinder head cover.

Installing
Install in reverse sequence; note the following
points.

- Seal end points of joints between bearing caps and cylinder head.
- Before installing cylinder head cover and gasket, carefully apply a
small quantity of sealant D 454 300 A2 at four end points of sealing
surfaces on cylinder head -arrows-, using a small screwdriver.
Pa
ge 28 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-30


- Unplug connector for camshaft timing control -1- (cylinder bank 4..6).
- Unplug connectors from injectors -2- (cylinder bank 4..6).
- Unplug connectors from ignition coils -3- and move wiring harness
clear (cylinder bank 4..6).
- Pull crankcase breather -4- off cylinder head cover (cylinder bank 4..6).
- Remove ignition coils.

- Unplug connectors from injectors -2- (cylinder bank 1..3).
- Pull off hose -5- going to turbocharger intake side.
Pa
ge 30 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1