warning AUDI A5 CABRIOLET 2010 Owners Manual

Intelligent technology
'-------------------------------------------------
Corrosion
T he re may be a te ndency fo r d irt to build u p on the bra ke pads and
co rrosion to form on the d iscs if the car is not dr iven reg ularly o r only
for short trips with litt le use of the bra kes .
If the brakes a re not used freq uen tly, or if co rrosion has formed o n
the discs, it is advisable to clean off the pads and discs by braking
fir mly a few times from a mode rat ely h igh spee d~ & .
Faults in the brake system
If yo u sh ou ld noti ce a sudden increase in b rake peda l trave l, then one
of the two brake circu its may have failed~& .
Low brake fluid level
Ma lfunctions can occ ur in t he brake system if the brake fluid level is
t oo low. The bra ke f lu id level is moni tore d elec tron ically.
Brake lin ing wear status
Brake lin ing wear may be checked by v isua l inspect ion of the condi­
tion of the brake pads throu gh the open ings in the whee l.
If neces­
sary, the whe el may be removed fo r thi s insp ection~
page 320,
"Changing a w hee l".
& WARNING
• You should perform braking maneuvers for the purpose of
cleaning the brake system only if road conditions permit. Other
road users must not be put at risk - you may cau se an accident!
• Before descending a steep grade, reduce speed and shift trans­
mission into a lower gear or lower driving range. Do not ride the
brakes or hold the pedal down too long or too often . This could
cause the brakes to get hot and diminish braking efficiency.
• Do not "ride the brakes " by resting your foot on the pedal when
you do not intend to brake . This may cause the brakes to overheat ,
premature wear and increased stopping distance.
• Under certain climatic and operating condition s such as
passing through water , driving in heavy rain or after washing the
& WARNING (co ntinued )
vehicle, the effectiveness of the brakes can be reduced . In winter,
ice can ac cumulate on the brake pads, linings, dis cs and drums.
Carefully apply brakes for a test. Brakes will dry and ice coatings
will be cleaned off after a few careful brake appli cations.
• Driving for an extended period of time on salt-covered roads
without u sing your brakes can also affect braking efficiency . Clean
off accumulated salt coating from b rake discs and pads with a few
careful brake applic ations.
• If you damage the front spoiler, or if you install a different
spoiler, be sure the air flow to the front brakes i s not obstructed .
Otherwise the brake system could overheat reducing the effective­
ness of the entire brake system.
• Failure of one brake circuit will impair the braking capability
resulting in an increased stopping di stance. Avoid driving the
vehicle and have it towed to the nearest authorized Audi dealer or
qualified workshop.
n
Brake booster
The b roke boost er odds extra broking po wer.
The bra ke boos ter wor ks wi th v acuum pressure whi ch is crea ted o nly
when the eng ine is ru nning~ &.
& WARNING
• Never let the vehicle roll to a stop with the engine shut off.
• If the brake booster is not working, for example when towing
your vehicle , or because the brake booster has somehow been
damaged, the brake pedal mu st be pressed considerably harder to
make up for the lack of booster assistance. •

Intelligent technology
--------------------------------------------------' '----'----
Functioning of Anti-Lock Brake System
(ABS}
ABS prevents the wheels from locking up under braking.
The ABS contributes effectively to vehicle control since it prevents the
w heels from
locking whe n the brakes are applied . This means t hat t he
vehicle rema ins steerable and is less likely to skid.
With ABS you do not need to pump the brake. Ju st hold the brake
pedal down .
However, do not expect the ABS to shorten braking distance under all
circu mstances. When d riving on gr ave l o r on new ly falle n snow o n top
of icy s urfaces, braking distance may be even longer, therefore, under
t he se c ir cu mstances, i t is especially importa nt that you dr ive slowly
and with great care.
How the ABS system works
An a utomat ic check is made when a speed of about 12 mph (20 km/h)
is reached. When this happens, a pumping noise can be heard.
If an individ ual w heel beg ins to rotate too slow ly in relat ion to vehicle
speed and tends to lock, t he ABS automat ic al ly reduces brake pres­
sure to prevent t hat wheel from locking .
Thi s automatic adjustment process w ill cause a
slight vibrat ion of
t he bra ke ped al and some noises to aler t you th at vehicle s peed mus t
be adapted to existing road and traff ic conditions.
& WARNING
Although the ABS is very effective , always remember that braking
capability i s limited by tire traction . Always adjust your driving
speed acco rding to the road and traffic condition s. Do not let the
extra safety afforded by the ABS tempt you into taking extra risk s.
T he ABS cannot overcome the laws of physics .
Controls and equip­ ment Safety first Vehicle operation
(I] Tips
•
If ABS is no t fun ct io ni ng prope rly, a wa rning light will come on .
See =>
page 16.
• If a fault occurs in the A BS, the EDL is also not functioning . This is
indicated by t he ABS warn ing light .•
Brake assist
Brake assist is designed to achieve the optimum braking
effect.
Bra ke ass ist helps to i ncrease the effe ctive br aking power and thus to
achieve a shorte r stopping distance . If the d river presses the brake
peda l very quickly, brake assist automatically boosts the bra king
force to the max imum level, up to the po int whe re the anti-lock b rake
function (ABS) intervenes to stop t he wheels from locki ng . You
should then keep the br ake peda l pressed unti l the ve hicle has braked
to the required speed . Brake ass ist switches itself off as soon as you
re le ase the br ake pedal.
& WARNING
Please remember that the accident risk always increases if you
drive too fast , especially in corners or on a slippery road , or if you
follow the vehicle ahead of you too clo sely. Increased ri sk of an
accident cannot be compensated for even by brake assist , so
alway s maintain a safe speed. •
Vehicle care Do-it-yourself service Technical data

Intelligent technology
--------------------------------------------------' "---.L=.c=--
Repl acing wheel s/tires
Vehicles wi th all wheel drive must a lways have tires of t he same size.
Also avoid tires with different tread depths. For details see page
=> page 307, "New tires and rep lacing tires and wheels".
Off -Road driving?
Your Audi does not have enough ground clearance to be used as an
off-road veh icle . It is therefore best to avo id ro ugh tracks and uneven
terrain as m uch as possible . Also refer to=>
page 251.
& WARNING
Alway s adju st your driving to road and traffi c conditi ons. Do not
let the ex tra safety afforded by all wheel dr ive tempt you into
taking extra risks.
• Although the all wheel dri ve is ve ry effecti ve, always
remember that braking capacity is limited by tire traction. You
should therefore not dri ve at ex cessive speeds on icy or slippery
road surfaces .
• On wet road surfaces , be careful not to drive too fast because
the front wheel s could begin to slide on top of the water (aqua­
planing ). If th is should occur, you will have no warning from a
sudden increase in engine speed as with a front-wheel drive
vehicle. Always drive at speeds which are suited to the road cond i­
tions -ris k of crash.
n
Controls and equip­
ment Safety first Vehicle operation
Energy management
Starting ability is optimized
E
nergy management contr ols th e distributi on of elec­
tri cal energy and thus optimizes the availabili ty of elec­
tri cal energ y for star ting the engin e.
If a vehicle with a conventiona l energy system is not dr iven for a long
per io d of time, t he battery is di sch arged by idling cur rent consume rs
(e .g. immob il izer) . In certain c ircumstances it can result in there
being insuffic ien t energy av a ilab le to start t he eng ine .
Inte lligent energy management in your ve hicle hand les the d istribu ­
tion of e lectrical energy . Starting ability is ma rkedly improved and
the l if e of the battery is extended.
Bas ically, energy management consists of
battery d iagnos is, idling
current management
a nd dynamic energy management .
Battery diagnosis
Battery d iagnosis con tinuously dete rmines the st ate o f the batte ry.
Sensors determ ine battery vo ltage, battery current and battery
t empe ra ture. This de termine s the cur rent sta te of cha rge and the
power of the battery.
Idling current management
I d ling current management reduces energy consumption wh ile the
vehicle is s tanding. W ith t he igni tion swi tched off, it con trols the
energy supply to the var io us electrical components. Data from
b att ery diag nosis is considered .
Depend ing on the battery 's state of charge, individual consumers a re
gradually t urned off to p revent excessive discha rge of the battery and
thus main tain start ing capab ility.
Dynamic energy management
Whi le the vehicle is being dr iven , dynamic energy management
dis tributes the energy generated a cco rding to the needs o f th e in di-
Vehicle care Do-it-yourself service Technical data

Intelligent technology
'-------------------------------------------------
vi dual components. It regulates consumption, so that more electrical
energy is not being used than is being generated and ensures an
optimal state of charge for the battery .
[I] Tips
• But even energy management cannot negate the limits of physics.
Consider that the power and life of a battery are limited.
• If starting ability is threatened, you are informed by a warning
~ page 249, "Driver notification in the instrument cluster display" .•
What you should know
The highest priority is given to maintaining starting capa ­
bility.
Th e battery is severe ly taxed in short-distance driving, in city traffic
and during the cold time of year. Abundant electrical energy is
required, but only a little is generated.
It is also critical if the engine
is not running and electrical components are turned on. In this
instance energy is being consumed but none is being generated.
It is in prec ise ly these sit uations that you will notice energy manage­
ment actively regulating the distribution of energy.
Vehicle stands for an extended period
If you do not drive your vehicle over a period of several days or weeks,
electrical components are gradually cut back or sw itched off. This
reduces energy consumption and maintains starting capability over a
longer period.
Take into consideration that when you unlock your vehicle, some
convenience functions, such as the remo te key or power seat adjust­
ment, may not be available. The convenience functions will be avail­
able again when you turn on the ignition and start the engine.
W ith the engine turned off
If you listen to the radio, for example, with the engine turned off or
use other MMI functions, the battery is being discharged .
If starting capability is jeopardized due to energy consumption, the
following warning appears in the MMI display:
Please start engine, otherwise system will switch off in
3 minutes.
Th e warn ing indicates that the system will be turned off automati­
cally after 3 m inutes. If you wish to continue using the functions, you
have to start the engine.
With the engine running
Although electrica l energy is generated when the vehicle is being
driven, the battery can become discharged. This happens most ly
when little energy is being generated and a great deal consumed and
the battery's state of charge is not optimal.
T o br ing the ene rgy balance back into equilibrium, consumers which
require especially large amounts of energy are temporarily cut back
or switched off. Heating systems in particular require a great deal of
energy .
If you notice, for example, that the heated seats* or the
heated rear window are not heating, they have been temporarily cut
back or switched off. These systems will be ava ilable again as soon as
the energy ba lance has been restored.
You will also notice that engine idle speed has been increased
slightly. This is normal and not a cause for concern. By increasing
eng ine id le speed the additional energy required is generated and the
battery is charged. •

Driving and environment
Driving and environment
The first 1,000 miles (1,500 km)
and afterwards
New engine
The engine needs to be run-in during the first 1,000 miles
(1,500 km) .
For the first 600 miles (1,000 kilometers):
Do not use full throttle .
- Do not drive faster t han 3/ 4 of the top speed mar ked on
the speedomete r.
- Avoi d high engine speeds .
From 600 to 1,000 miles (1,000 to 1,500
kilometers):
-Spe eds can g radually be inc reased to th e maximu m
permissib le road o r engine spee d.
During and after break-in period
- Do not rev the engine up to high speeds w hen it is cold.
This applies whet her t he tra nsmission is in N ( Neutral) or
1n gear .
After the break-in period
-Do not exceed max imum engi ne spee d under any circum­
s ta nces .
- Ups hift i nto t he next hi gher gear
befor e reachi ng t he red
ar ea at t he end of the tachometer scale =>
page 8.
Dur ing the first few hou rs of d riving, the engine 's interna l frictio n is
higher than later when a ll the mov ing pa rts have been b ro ken in . How
we ll thi s brea k-in p roce ss is done depe nds to a considerable extent on
the way the veh icle is driven dur ing the first 1,000 m iles (1,500 ki lo­
mete rs).
0 Note
Ex tremely high engine s peeds a re au tom atic ally red uced . H owever,
these rpm limits are programmed fo r a n engine we ll run-in, not a new
eng ine .
For the sake of the environment
Do not drive w ith unnecessari ly hi gh eng ine speeds -upshifting early
saves fuel, reduces noise and protec ts the env ironment .•
New tires
If your vehic le is running on new t ires, drive very caref ully for
the firs t 350 m iles (500 kilome ters) afte r fitt ing .
& WARNING
New tires tend to be slippery and must also be "broken-in ". Be
sure to remember th is during the first 350 miles (500 kilome­
ter s). Brake gently. Avoid following closely behind other vehicle s
or other situation s that might require sudden, hard brak ing. •