mirror AUDI A5 COUPE 2010 User Guide

Storing and recalling settings
With the help of the memory buttons 1 and 2
~ page 74, fig. 75 the
settings for two different drivers can be stored and recalled
~ page 75.
The current settings are also automatically stored on the remote
control key being used when the vehicle is locked. When the vehicle
is unlocked, the settings stored on the remote control key being
used are automatically recalled.
Turning seat memory on and off
If the [ ON /OFF
I switch is depressed, the seat memory is inoperative.
The word
OFF in the [ON/OFF I switch illuminates.
All the stored settings are retained . We recommend using the
I ON/OFF I switch and deactivating the seat memory if the vehicle is
only going to be used
temporarily by a driver whose settings are not
going to be stored. •
Applies to vehicles : w ith seat m emo ry
Storing and recalling settings
Before you can store or recall your settings, the [ON/OFF]
switch on the seat memory must be engaged (not raised).
Storing settings
- Adjust the driver's seat .
- Adjust the two exterior mirrors.
- Press the [SET] button and hold it down. In addition ,
press one of the memory buttons for at least one second.
- Release the buttons. The settings are now stored under
the corresponding memory button.
Controls and equip ­
ment
Seats and storage
Recalling settings If the driver's door is open, tap the corresponding
memory button briefly.
If the driver's door is closed, press the appropriate
memory button until the stored position is reached.
Successful storage is confirmed audibly and by the light in the [SETI
button illuminating ~ page 74, fig. 75.
When the vehicle is
locked, the current settings are stored and
assigned to the remote control key. But the settings stored on
memory buttons 1 to 2 are not deleted. They can be recalled at any
time. When the vehicle is
unlocked, the settings stored on the
remote control key are restored.
If your vehicle is driven by other persons using your remote control
key, you should save your individual seat position on one of the
memory buttons. You can recall your settings again simply and
conveniently by pressing the corresponding memory button. When
the vehicle is locked, these settings are automatically re-assigned to
the remote control key and stored.
& WARNING
• For safety reasons, the seat setting can only be recalled when
the vehicle is stationary -otherwise you risk having an accident .
• In an emergency the recall procedure can be cancelled by
pressing the [
ON/OFF I switch or by tapping of the the memory
buttons. •
I • •

Audi sid e as sis t -
-------------------'
Audi side assist
Lane change assistant
Applies to veh icles: w it h s id e ass is t
Description
The side assist helps you when changing lanes.
A UD I
•
a F ig . 14 4 Rea r bump er:
P os it io n of ra dar
se ns ors ! not vis ible on
out side)
Fi g. 14 5 Signa l lig ht
o n th e ou tsid e mirr or -
d riv er's s ide
Side assist uses radar sensors (not visible on outside)=> fig. 144 to
help the driver check blind spots, and see what is happening in
traff ic behind the vehicle=>
page 137, fig. 147 .
Signal lights are built into both outside mirrors
G) => fig. 145 . The
signa l light on the left outside mirr or assists when moving over in to
Con tro ls and eq uip­
ment
the left lane and the signal light on the right outside mirror assists
when moving over into the right lane.
The signa l ligh t comes on to te ll you that s ide assist has detected a
vehicle on that side and tha t the position of this o ther vehicle
should be taken into account i f you we re to change lanes . This is
called the
inform ati onal sta ge sign al=> page 137 . The informational
stage signal is designed so that you notice it only when you are
looking in the outside mirror .
When you activate th e turn signal and side assist detects a vehicle
in a notable location, the corresponding signa l on the outside
mirror flashes briefly and brightly sev eral tim es. This is the
al ert
s tage sign al=>
page 137. •
Applie s to v eh ic les : wi th si de assi st
Activating and deactivating
Fig . 146 Driv er's doo r:
Si de assis t bu tton
Activating
Press the ~ fig. 146 butt on. The indic ator on the button
lig hts up.
~
Vehicle care I I Technical data

• .___A_ u_ d_ i_s_ i_ d _e_ a_ s_ s_is _ t __________________________________________________ _
Deactivating
- Press t he bu tton again. The in dicato r ligh t on the but to n
g oes ou t.
The system works at speeds faster than 19 mph (30 km/h) .
& WARNING
• Improper reliance on the side assist system can cause colli­
sions and serious personal injury :
- Never rely only on side assist when changing lanes .
- Always che ck rear view mirrors to make sure that it is safe to
change lane s.
• Side assist cannot detect all vehicles under all conditions­
danger of ac cident!
• Side assist cannot detect vehicles in time to alert you when
they approach from behind at very high speed, or f all drop back
very quickly.
• The radar sensor 's
vision can be reduced or entirely blocked by
rain , snow , and heavy spray . This can result in side assist not
adequately detecting vehicles or , in some cases, not dete cting
them at all . Always keep an eye on the direction you are traveling
and the relevant area around the vehicle .
• Please note that side assist indicates there a re approaching
vehicles , or vehicles in your blind spot , only after your vehicle has
reached a driving speed of at least 19 mph (30 km /h).
• Side assist s ignal does not work around tight corners (turning
radius less than 328 feet or 100 m l.
• Side assist is no replacement for the driver's full attention . The
driver alone is responsible for lane changes and similar driving
maneuvers . Always keep an eye on the direction you are traveling
and the relevant area around the vehicle.
0 Note
• T o ensure t hat you do n ot adve rsely affect side ass is t, do not
block the area on the rear b umper whe re the radar sensors a re
lo cate d with for eign objects (suc h as st ic ke rs or b icycle racks).
• M ake s ure that the s igna l lig ht on the outside mi rror is not
blocked by st ickers o r other it em s.
[ i ] Tips
• Side ass ist auto matical ly deact ivates if it det ects that t he radar
sensors are blocked => page
142. The indicator light on the button
goes out .
• T he area on the b umpe r where the rada r senso rs are located
m ust co nsistently rema in fr ee o f snow, ice, a nd hea vy soiling so t hat
side assist can function properly. Fo llow the additiona l notes on
=> page
143.
• Additiona l tinting on the front side windows can make it harde r
t o see and co rrect ly u nderstand the si gna l lig ht o n th e outs ide
mirror.
• For Declarat ion o f Compl iance to Un ited States FCC and Ind ustry
Canada regulations => page
342 . •

_________________________________________________ A _u_ d_ i _s _ i_d _e _ a_s_ s_ i_ s _t __ !II
Ap plies to vehi cle s: w ith side a ssist
Sensor detection area
Fi g. 14 7 Sc hem atic
illu stra tion: Senso r
d etec tion area
The detection => fig . 147 of the radar sensor detection area is made
up of:
• the approach area (light green area)
0, about 230 feet (70 m)
behind the vehic le, and
• the "blind spot" (dark green areal@.
The radar sensors cover the adjacent left and right lanes. Other
lanes are
not covered by the radar sensors.
[ i ] Tip s
Side assist does not measure actual lane width. The system
assumes a fixed lane width . Detection in the left and right lanes is
based on this assumed lane width . When driving on narrow roads or
when driving to the left or right of the center of a trave l lane, it is
possible that vehicles will be detected that are
not in the lane next
t o the lane you are using=>
page 142. •
Controls and equip ­
ment
Ap plies to veh ic les : wi th side ass ist
Operation
Side assist compares the distance and difference in speed of
detected vehic les with the speed of your vehic le. Whenever the
difference in speed a nd distance is registered as notable if you were
to change lanes , a signal light appears on the respective mirror .
The signal can light up if you are passed by a vehicle or if you are passing another vehicle.
If you pass another vehicle slow ly (difference in speed less than 9
mph, or
15 km/h), the signal light wil l come on as soon as the o ther
vehic le is in your b lind spot and is detected by side assist. When the
difference in speed is greater, the signal light will not come on .•
Ap plies to vehi cles : with si de assi st
Informational and alert stage signals
Side assist has two signal stages:
• t he informational stage s igna l, and
• the alert stage signal.
Side assist helps you by using the appropriate signa l stage,
depending on whether or not you have activated the tu rn signal,
and thus have indicated that you are or are not changing lanes .
Infor mation al stage signal
As long as you have not activated the turn signa l, side assist informs
you of detected vehicles that are registered as being in a notable location if you were to change lanes. Whenever the detected
vehicle's difference in speed and distance is registered by side assist as notable, the signal light on the respective mirror produces
muted illumination.
The brightness of the informational stage signa l is designed not to
be as intense, so that it does not interfere with your view of the road
when you are driving and have no intention of changing lanes. .,
I • •

• ..__A_ u_ d_ i _s _i_d _e_ a_ s_ s _ is_ t __________________________________________________ _
When you look in the outside mirror, you can clearly see the infor­
mational stage signal.
Alert stage signal
When you activate the turn signal, and side assist has detected a
vehicl e in a notable location on that particular side , the signal light
on this side mirror flashes brightly. The repeated brief and bright
flashing of the alert stage signal reminds you to carefully check
traffic to the rear in the outside mirror and over your shoulder, so
that you can safely complete the lane change=>
& in "Safety tips"
on
page 143.
[ i J Tips
The brightness of the signal light on the outside mirrors can be
adjusted with the
MMI* => page 141. •
Applies to veh ic les: w it h side assist
Driving situation: Fast approaching vehicles
Fig . 148 Side assist: Fast approaching vehicles
0 Signal on outside mirror does not light up
No vehicle was detected by the sensors. The signal on the outside
mirror does not light up::::>
& in "Safety tips" on page 143 .
0 Informational stage signal lights up
A fast approaching vehicle -in the left-hand lane fo r example -was
detected by the sensors. Although this vehicle is still far away, it
should be taken in to accoun t if you were to change lanes , due to the
considerable difference in speed. The informational stage signal on
the outside mirror lights up::::>
page 137.
© Alert stage signal flashes
If you activate your turn signal in driving situation 0, the signal
briefly flashes repeatedly. Side ass ist is alerting you to a vehicle that
you may not have noticed. .,

___________________________________________________ A_u_ d_i_ s_ id_e_ a_ s_s _i_s _t _ __.9I
[ i J Tip s
• The fast er a veh icle approaches from the rear, the sooner the
signa l on the outside mirror lights up. Side assist will signal, at the
latest, when a detected vehicle enters your "blind spot" .
• When vehicles approach very quickly, changing lanes can be
dangerous even i f the signa l on the outside mirror does not light
up .•
Ap plies to vehicl es: with side assist
Driving situation : Slowly approaching
vehicles
F ig. 149 Side a ssist: Slowly approaching v eh ic les and ve hic les in your blind
s pot
G) Signal on outside mirror does not light up
A vehic le approaching slowly -in the left -hand lane fo r example -
was d etected by the sensors. Because o f the s mal l difference in
Con tro ls and eq uip­
ment
speed and the considerab le distance from your vehicle, the signal
on the outside mirror will not light up~.& in "Sa fety tips" on
page 743 .
© Informational stage s ignal lights up
The distance between your vehicle and that of the slow ly
approaching vehic le has na rrowe d. The informationa l stage signal
on the outside mirror lights up .
As soon as the difference in speed and distance is registered as notable if you were to change lanes, a signal on the mirror lights up.
Side assist wi ll signal at the latest when a detected vehicle enters
your "blind spot" .
© Alert stage signal flashes
If you activate your turn signal in driving situation@, the signal
light briefly flashes repeatedly. Side assist is alerting you of a
veh ic le that you may not have noticed .
[ i J Tip s
• The faster a vehicle a pproaches from the rear, the soone r the
signal on the outside mirror lights up . S ide assist will signal, at the
latest, when a de tected vehicle enters your "blind spot" .
• When vehicles approach very quickly, changing lanes can be
dangerous even if the signa l on th e outside mirror does not light
up. •
Vehicle care I I Technical data

• ..__A_ u_ d_ i _s _i_d _e_ a_ s_ s _ is_ t __________________________________________________ _
Applies to vehicles : wi th side assist
Driving situation: Vehicles dropping back
slowly
Fig. 150 Side assist: Vehicles dropping back slowly
G) Signal on outside mirror does not light up
The vehicle that you passed has not yet been detected by side assist.
The signal on the outside mirror does not light up=>
& in "Safety
tips" on
page 143.
0 Informational stage signal lights up
A vehicle dropping back slowly on the right (difference in speed of
less than 9 mph, or 15 km/h) has been detec ted by side assist. The
informational stage signal on the outside mirror lights up.
G) Alert stage signal flashes
If you activate your turn signal in driving situation G), the signal
briefly flashes repeatedly. Side assist is alerting you of a vehicle that
you may not have noticed. •
Applies to vehi cles: with sid e a ssist
Driving situation: Vehicles dropping back
quickly
Fig. 151 Side assist: Vehicles dropping back quickly
G) Signal on outside mirror does not light up
The vehic le just passed has not yet been detected by side assist. The
signal on the outside mirror does not light up=>
& in "Safety tips "
on
page 143.
0 Signal on outside mirror does not light up
The vehicle dropping back quickly on the right (difference in speed
of more than 9 mph, or 15 km/h) has been detected by side assist,
but is not considered notable in the event of a lane change, because
it is dropping back so quickly. The signal on the outside mirror does
not light up=>
& in "Safety tips" on page 143. .,,.

___________________________________________________ A_ u _ d_i_ s_ id_ e_ a _ s_s _ i_s _t __ llllll
© Signal on outside mirror does not light up
If you activate your turn signal in driving situation @, the signal still
does not light up on the outside mirror=>
& in "Safety tips" on
page 143. •
Applies t o vehicles: with side assist
Setting the signal brightness on the outside
mirror
The signal brightness can be set in the radio or MM/*.
Fig. 152 MMI Display:
Adjusting sign al
brigh tness
- Select: Function button [CARI> Audi side assist
=> fig. 152.
- Rotate the cont ro l knob to adjust the displayed bright-
ness of the signal light on the outside mirrors .
The brightness of the signal light for both the informationa l and
alert stages is automatica lly adjusted to ambient light conditions. In
addition, you can adjust the
basic brightness separately, via the
brightness function
=> fig . 152.
While making the adjustment, the new brightness setting is
displayed briefly. The brightness displayed is that of the informa ­
tional stage signal. The alert stage signa l brightness is linked to the
informational stage signal brightness .
Controls and equip ­
ment
The informational stage signal brightness should be adjusted so
that you notice the signa l illumination when you look in the outside
mirror, but not when you look forward through the windshield.
In very dark or light surroundings, the automatic brightness setting
adjusts signal ligh t brightness to maximum or minimum intensity,
as needed . In circumstances such as these, you may not notice any
change in the brigh tness on the outside mirror when adjusting the
basic brightness.
You may not notice the change until lighting conditions are normal
again.
[ i ] Tips
• Side assist is not active when the basic brightness is adjusted.
The signal light comes on briefly to help you make the adjustment .
• Your settings are automatically stored and assigned to the
remote control key being used.•
Applies to veh ic les: with s ide ass ist
General information
Side assist has limits and cannot detect vehicles under a ll road and
weather conditions . Please remember system limitat ions and never
re ly on the system, especially when:
• driving through curves=>
page 141,
• lanes are of different widths=> page 142. •
Applies to veh ic les : with s ide ass ist
When driving through curves
Side assist cannot detect vehic les in curves with a turning radius of
less than 328 feet (100 ml. .,,
I • •

• .___A_ u_ d_ i_s_ i_ d _e_ a_ s_ s_is _ t __________________________________________________ _
When driving through a curve, it is possible that side assist may
register a vehicle two lanes over, and the signal on the outside
mirror will light up.•
Applies to veh icles: with side assist
Lane width
Fig. 153 Lanes of a
normal width are in
detection area
Fig. 154 Narrow lanes :
Side assist may detect
vehicles two lanes
away
Side assist's detection area is designed to cover lanes of standard
width to the left and right of your travel lane, depending on whether
you drive in the center of your lane or closer to the edge.
If you drive in narrow lanes, side assist's detection area may also
include other lanes -especially if you tend to drive on the edge of
your lane=> fig. 154. Under these conditions, vehicles can also be detected that are two
lanes away, and side assist then could switch
between the informational and warning stage signals.
When driving in very wide lanes, vehicles in the adjacent lane may
not be detected because they are not inside the detection area. •
Notes
Applies to vehicles: with side assist
Messages in instrument cluster display
If side assist turns off automatically, the indicator light on the
button will go out and you will see a message in the instrument
cluster display:
Audi side assist not available : sensors possibly blocked
The side assist sensors are built into the rear bumper on the left and
right (not visible on the outside)=? page 135, fig, 144. To ensure that
you do not adversely affect the way side assist functions, foreign
objects (such as stickers or bicycle racks) should not be attached to
the area on the rear bumper where the sensors are located. If side
assist functions are adversely affected, you will see this message in
the instrument cluster display. Remove anything that may be
blocking the sensors.
I f no vehicle is detected for a longer period of time while driving,
side assist will also switch off automatically.
Audi side assist currently not available
If there is a temporary problem (such as the vehicle's battery charge
being low), side assist cannot be activated temporarily.
Audi side assist: system fault
Have the system checked by an authorized Audi dealer or qualified
workshop. •

___________________________________________________ A_ u _ d_i_ s---- id ___ e....:. a:..:s :..:s :..: i..::s :..:t __ ftllll
Ap plies to vehi cle s: w ith side a ssist
Safety tips
The side ass ist detec tion may be l imited w hen d riv ing ar ound
narrow street corners, on hi lly streets, and under poor weather
co nd ition s.
I t is possible that the radar sensors may also detect other objects,
suc h as high o r stagge red guardra ils .
S ide ass ist does not meas ure ac tua l la ne widt h. The syste m
assumes a fi xed lane width . Detection in the left and right lanes is
b ased on this assu med lan e wid th. Whe n driv in g o n na rro w roa ds or
when driving to the left or r ight of the c enter of a trave l lane, it is
po ssi ble that ve hic le s will be detec te d tha t are
no t in th e lane next
to the lane you are using .
& WARNING
• Improper reliance on the side assist system can cause colli ­
sions and serious personal injury:
-Never rely only on side assist when changing lanes .
- Always check rear view mirrors to make sure that it is safe to change lanes .
• Side assist cannot detect all vehicles under all condition s­
danger of accident!
• Side a ssist cannot detect vehicles in time to alert you when
they approach from behind at very high speed , or fall drop back
very quickly.
• The radar sensor's
vision can be redu ced or entirely blocked by
rain, snow , and heavy spray . This can result in side assi st not
adequately detecting veh icles or , in some cases , not detecting
them at all . Always keep an eye on the direction you are traveling
and the relevant area around the vehicle.
Controls and equip ­
ment
& WARNING (continued )
• Please note that side assist indicates there are approaching
vehicles, or vehicles in your blind spot , only after your vehicle has
reached a driving speed of at least 19 mph 130 km/h).
• Side assist signal does not work around tight corners (turning
radius less than 328 feet, or 100 ml. • S ide assist is no replacement for the driver' s full attention. The
driver alone is responsible for lane changes and similar driving
maneuvers . Always keep an eye on the direction you are traveling
and the relevant area around the vehicle .
(D Note
To ensu re that side assist is not adversely affected , you sho uld not
b lock the area on the rear bumper where t he radar s ensors are
located with foreign objects (such as with stickers or bicycle racks) .
[ i ] Tips
If the positions of the radar sensors have been changed as a result
o f a re ar end -c olli sio n, for i nsta nce, have s ide ass ist c hecked by a n
authorized Audi dea ler for safety reasons .•
I • •