fuel AUDI A5 COUPE 2010 Owner's Guide

The labe l on the inside of the fuel filler flap tel ls you the correct fuel
fo r your vehicle . For mo re information about fuel specifications, see
=> page 265.
Your vehicle fuel tank has an on -board refuelling vapor recovery
sys tem. Th is feature helps to prevent fue l vapors from escapin g
from the tank and polluting the environment wh ile you refue l your
veh ic le . I n order to fill the tank properly while protecti ng the envi­
ronment, please follow this refuel ing procedure carefully .
& WARNING
Under normal operating conditions , never carry additional fuel
c ontainers in your car . Ga s canister s and other containers used to
transport fuel can be dangerous . Such conta iners , full or empty,
may leak and could cause a fire in a collision . If you mu st transport
fuel to use for your lawn mower , snow blower , etc. , be very c areful
and always ob serve local and state laws regarding the u se , tran s­
port ation and storage of su ch fuel containers . Make certain the
c ontainer meets industry standard s (ANSI/ASTM F852 · 86 1.
0 Note
Neve r d rive your vehicle until the fuel tank is completely emp ty . The
irregular supp ly of fuel can cause misfiring . Gasoline could enter
t he e xhaus t system and damage the cataly tic converter. •
Fuel supply and filling your fuel tank
Refuelling
Fig . 2 16 Right rear
v ehicle side : Open ing
th e fu el filler flap
Fig . 2 17 Fuel filler fla p
with attach ed fu el cap
Wh en act iv ati ng th e ce ntral loc kin g, the fuel fille r flap is
a utomatically unlocke d or locked . Ref uel t he vehicl e wit h
t h e ig nition t urn ed
off.
Taking the fuel cap off
- Turn off the ignit io n .
Press the left side of the fuel filler flap to open it
=> fig. 2 16 -arro w-.
U nsc rew fue l ca p cou nter -c lockwise and hang it on t he
fuel filler flap=> fig . 2 17 . .,
Vehicle care I I irechnical data

Fuel supply and filling your fuel tank Refuelling procedure
- Insert the fuel nozzle from the gasoline pump into the
fuel filler neck as far as it will go.
- Select a medium refuelling rate so that the nozzle switches off automatically when the tank is full.
Putting the fuel cap back on
- After filling your tank, twist the fuel cap clockwise as far
as it will go.
- Close the fuel filler flap.
To avoid fuel spilling or evaporating from the fuel tank always close
fuel cap properly and completely.
& WARNING
Improper refueling or handling of fuel can cause fire, explosion
and severe burns.
• Fuel is highly flammable and can cause severe burns and other
injuries.
• Failure to shut the engine off while refueling and/or to insert
the pump nozzle fully into the fuel filler neck could cause fuel to
spray out of filler neck or to overflow. Fuel spray and overflowing
fuel can cause a fire.
• Never use a cellular telephone while refueling. The electromag­
netic radiation can cause sparks that can ignite fuel vapors and
cause a fire.
• Never get back into your vehicle while refueling. If in excep­
tional circumstances you must get back in your vehicle while refu­ eling, make certain that you close the door and touch metal to
discharge static electricity before touching the filler nozzle again.
Static electricity can cause sparks that can ignite fuel vapors
released during refueling.
& WARNING (continued)
• Never smoke or have an open flame anywhere in or near your
vehicle when refueling or filling a portable fuel container.
• For your safety, we strongly recommend that you do not travel
with a portable fuel container in your vehicle. The container, full or
empty may leak and could cause a fire, especially in a crash.
• If, under exceptional circumstances, you must transport a
portable fuel container, please observe the following:
-Never fill a portable fuel container while it is anywhere in or
on the vehicle (for example, in the luggage compartment, or on
the trunk). Static electricity can build up while filling and can
ignite fuel vapors causing a fire.
- Always place a portable fuel container on the ground before
filling.
- Always keep the filler nozzle completely inside the portable
container before and during filling.
- If filling a portable container made of metal, the filler nozzle
must always be in contact with the container. This will help
prevent static electricity from discharging and cause a fire.
- Never spill fuel inside the vehicle or luggage compartment. Fuel vapors are highly flammable .
- Always observe local and state/provincial laws regarding the
use, storage and transportation of fuel containers.
- Make certain the fuel container meets industry standards
(ANSI / ASTM F852-86l.
0 Note
If any fuel has spilled onto the car, it should be removed immedi -
ately to prevent damage to the paint. _.,

<£> For the sake of the environment
As soon as the correctly operated nozzle switches off automatically
for the first time, the tank is full. Do not try to add more fuel because
fuel may spill out. In addition, the expansion space in the fuel tank
will be filled -causing the fuel to overflow when it becomes warm
and pollute the environment.
[ i] Tips
• Running your engine while refuelling may cause vapors to
escape or even cause fuel to spill out of the tank. This would then
shut off the fuel nozzle before the tank is full.
• Do not refuel your vehicle with the ignition turned on. The fuel
gauge may otherwise not indicate the correct fuel level after refuel ­
ling .
• The fuel filler flap of your vehicle is not locked when you lock the
vehicle from the inside .•
Unlocking the fuel filler flap by hand
You can open the fuel filler flap by hand if the power
locking system should fail.
Fig . 218 Luggage
compartment : opening
the side trim
Fuel supply and filling your fuel tank
Fig. 219 Luggage
compartment: Emer­
gency opening of fuel
filler flap
The emergency opening mechanism is located behind the
right side trim panel in the luggage compartment.
Opening the side trim
- Insert a tool such as a screwdriver=:>
page 310 or the
emergency key into the right side of the upper gap
=:> fig. 218.
- Pry upward to release the trim.
Fuel filler door emergency release
- Loosen the strap from its bracket and pull on it
=:> fig. 219. You can now open the fuel filler flap as usual
=:> page 267. •
Vehic le care I I irechnical data

Checking and filling IJI
--------------~-
•
Closing the engine hood
-Pull the hood down until the pressure from the struts is
reduced .
- Let the hood
drop down and latch in place. Do not try to
push it shut;
it may fail to engage => &.
& WARNING
A hood that is not completely latched could fly up and block your
view while driving.
• When you close the engine hood, check it to make sure the
safety catch has properly engaged. The hood should be flush with
the surrounding vehicle body parts.
• If you notice while driving that the hood is not secured prop­
erly, stop at once and close it. •
Working in the engine compartment
Be especially careful whenever you work in the engine
compartment.
Whenever you must perform any work in the engine compartment,
for example checking and filling different fluids, there is a risk of injury, burns and accidents. To prevent personal injury always
observe the following WARNINGS. The engine compartment of any
vehicle is a hazardous area
~ & .
& WARNING
To help avoid injury, before you check anything under the hood :
• Turn off the engine.
• Remove the ignition key.
• Apply the parking brake .
& WARNING (continued)
• Move selector lever of automatic transmission to "P" (Park);
put manual transmission in Neutral .
• Always let the engine cool down. Hot components will burn
skin on contact.
• To reduce the risk of being burned, never open the hood if you
see or hear steam or coolant escaping from the engine compart­
ment. Wait until no steam or coolant can be seen or heard before
carefully opening the hood .
• Keep children away from the engine compartment.
• Never spill fluids on hot engine components . They can cause a
fire.
• Never touch the radiator fan. The auxiliary electric fan is
temperature controlled and can switch on suddenly.
• Never open the coolant reservoir cap when the engine is still
warm. The coolant system is pressurized and hot coolant could
spray out.
• Protect your face, hands and arm from steam or hot engine
coolant by placing a thick rag over the cap when you open the
coolant reservoir.
• If work on the fuel system or the electrical system is necessary:
- Always disconnect the battery.
- Never smoke or work near heaters or open flames. Fluids in
the engine compartment could start a fire .
- Keep an approved fire extinguisher immediately available.
• To avoid electrical shock and personal injury while the engine
is running or being started, never touch :
- Ignition cables
- Other components of the high voltage electronic ignition
system.
• If you must perform a check or repair with the engine running: ..,
Vehicle care
I t •

Checking and filling -
-----------------=-----==-----...J
0 Note
Driving with an insufficient oil level is likely to cause severe damage
to the engine.
[ i] Tips
• The oil pressure warning display~ is not an indicator of the oil
level. Do not rely on it. Instead, check the oil level in your engine at
regular intervals, preferably each time you refuel, and always before
going on a long trip.
• If you have the impression your engine consumes excessive
amounts of oil, we recommend that you consult an authorized Audi
dealer to have the cause of your concern properly diagnosed. Keep
in mind that the accurate measurement of oil consumption requires
great care and may take some time. An authorized Audi dealer has
instructions about how to measure oil consumption accurately. •
Checking the engine oil level
Read oil level
Fig. 223 MMI Display;
Oil level indicator
Select: Function button [CARI> Oil level.
- Park your vehicle so that it is horizontally level. Shut
the engine off when it is at operating temperature.
Wait approx. two minutes. Read the oil level in the MMI* Display=> fig. 223. Add
engine oil if the bar of the oil level indicator is near "Min"
=>
page 275
Depending on the way the vehicle is driven and the operating condi­
tions, oil consumption can be up to a 1/2 quart per 600 miles (0.5
liter per 1000 kml. Consumption may be higher within the first 3000
miles (5000 kml.
[ i] Tips
The oil level indicator in the MMI* Display is only an information
display. If the oil level is too low, a minimum oil warning appears in
the instrument cluster. Add oil
=> page 275. If the hood has been
opened, the current oil level is shown in the instrument cluster the
next time the ignition is switched on. •
Adding engine oil ~
Fig. 224 Engine
compartment; Oil filler
cap location
Before you check anything in the engine compartment,
always read and heed all WARNINGS=> & in "Working in
the engine compartment" on
page 271. .,,_
Vehicle care I I irechnical data

-~_T_ ir_e_ s_ a_ n_d _ w_ h_ e_e _l_s _________________________________________________ _
& WARNING (continued)
crashes and serious personal injuries . Have worn or damaged tires
replaced immediately.
• Tires age even if they are not being used and can fail suddenly,
especially at high speeds. Tires that are more than 6 years old can
only be used in an emergency and then with special care and at
low speed.
Glossary of tire and loading terminology
Accessory weight
means the combined weight (in excess of those standard items
which may be replaced) of automatic transmission, power steering,
power brakes, power windows, power seats, radio, and heater, to
the extent that these items are available as factory-installed equip­
ment (whether installed or not).
Aspect ratio means the ratio of the height to the width of the tire in percent.
Numb ers of 55 or lower indicate a low sidewall for improved
steering response and better overall handling on dry pavement.
Bead
means the part of the tire that is made of steel wires, wrapped or reinforced by ply cords and that is shaped to fit the rim.
Bead separation means a breakdown of the bond between components in the bead.
Cord
means the strands forming the plies in the tire.
& WARNING (continued)
• Never mount used tires on your vehicle if you are not sure of
their "previous history." Old used tires may have been damaged
even though the damage cannot be seen that can lead to sudden
tire failure and loss of vehicle control.
• If you notice unusual vibration or if the vehicle pulls to one side
when driving, always stop as soon as it is safe to do so and check
the wheels and tires for damage . •
Cold tire inflation pressure
means the tire pressure recommended by the vehicle manufacturer
for a tire of a designated size that has not been driven for more than
a couple of miles (kilometers) at low speeds in the three hour period
before the tire pressure is measured or adjusted.
Curb weight means the weight of a motor vehicle with standard equipment
including the maximum capacity of fuel, oil, and coolant, air condi­
tioning and additional weight of optional equipment.
Extra load tire
means a tire design to operate at higher loads and at higher infla ­
tion pressures than the corresponding standard tire. Extra load tires
may be identified as "XL",
"xi", "EXTRA LOAD", or "RF" on the side ­
wall.
Gross Axle Weight Rating ("GAWR")
means the load-carrying capacity of a single axle system, measured
at the tire -ground interfaces.
Gross Vehicle Weight Rating ("GVWR"l
means the maximum total loaded weight of the vehicle.

_L_T~ ir~e :..:s~ a~n~ d~ w~ h ~e~e~ l~ s '.,_ ______________________________________________ _
Sidewall
means that portion of a tire between the tread and bead.
Speed rating means the speed at which a tire is designed to be driven for
extended periods of time. The ratings range from 93 mph (150 km/h)
to 186 mph (298 km/h)=>
page 300. You may not find this informa ­
tion on a ll tires because it is not required by law.
The speed rating letter code, where applicable, is molded on the tire sidewa ll and indicates the maximum perm issible road speeds=>
&
in "Winter tires" on page 304.
Tire pressure monitoring system*
means a system that detects when one or more of a vehicle 's tires
are under inflated and illuminates a low tire pressure warning te ll­
tale.
Tread
means that portion of a tire that comes into contact with the road.
Tread separation
means pu lling away of the tread from the tire carcass.
Treadwear indicators (TWI)
means the projections within the principa l grooves designed to give
a visual indication of the degrees of wear of the tread . See
=>
page 297, "Tread Wear Indicator (TWI)" for more information on
measuring tire wear.
Uniform Tire Quality Grading
is a tire information system developed by the United States National
Highway Traffic Safety Adm inistration (NHTSA) that is designed to
help buyers make relative comparisons among tires. The UTQG is
not a safety rati ng and not a guarantee that a tire will last for a
prescribed number of miles (kilometers) or perform in a certain way.
It simply gives tire buyers additional informat ion to combine with
other considerations, such as price, brand loyalty and dealer recom-mendations. Under UTQG, tires are graded by the tire manufac­
t urers in three areas: treadwear, traction, and temperature resis­
tance . The UTQG information on the tires, molded into the
sidewalls.
U .S. DOT Tire Identification Number (TIN }
This is the tire's "seria l number". It begins with the letters "DOT"
and indicates that the tire meets al l federa l standards. The next two
numbers or letters indicate the plant where it was manufactured,
and the last four numbers represent the week and year of manufac­
ture. For example,
DOT ... 2209 ...
means that the tire was produced in the 22nd week of 2009 . The
other numbers are marketing codes that may or may not be used by
the tire manufacturer . This information is used to contact
consumers if a tire defect requires a reca ll.
Vehicle capacity weight
means the rated cargo and luggage load plus 150 lbs. (68 kilograms)
times the vehicle's tota l seating capacity as listed on the label
located either on the driver's side 8-pillar or on the inside of the fuel
filler flap.
Vehicle maximum load on the tire
means that load on an individual tire that is determined by distrib­
uting to each axle its share of the maximum loaded vehicle weight
and dividing by two.
Vehicle normal load on the tire
means that load on an individual tire that is determined by distrib­
uting to each axle its share of the curb weight, accessory weight,
and normal occupant weight (distributed in accordance with table
below =>
page 291) and dividing by two. _..

__________________________________________________ T_ ir_e _ s_ a_ n _ d_ w_ h_ e_ e_ls _ ____._
Occupant loading and distribution for vehicle normal load for various designated seating capacities
Designated seating capacity , num­
ber of occupants Vehicle normal load
, number of
occupants Occupant distribution in a normally
loaded vehicle
4
2 2 in front •
Cold tire inflation pressure
Tire pressure affects the overall handling, performance and safety of a vehicle.
Fig. 229 Tire pressure
label: located either on
driver's side B-pillar or
inside the fuel filler flap
Tir e pressure generally refers to the amount of air in a tire that it
needs it to do its job and safely carry the combined load of the entire
vehicle and its contents. T ire pressure is measured in kilopascals
(kPa), the international measuring unit and in pounds per square
inch (PSll. Tire pressure is based in part on the vehicle's design and
load limit -the greatest amount of weight that the vehicle can carry
safely and the tire size . The proper tire pressure is frequently
referred to as the "recommended cold tire inflation pressure." Air in
the tires expands when the tire heats up because of internal friction
when it flexes in use. The tire pressure is higher when the tire has
warmed up than when it is "cold." It is the inflation pressure in a
"cold" tire that counts. Therefore, you should never let air out of a
warm tire to match "cold tire inflation pressure" recommendations.
The tires would then be underinflated and could fail suddenly.
(.
~ ( SEATING CAPACllY JOTAL l:FRONT l:CENTER I )!EAR I )
TIRE AND LOADING INFORMATION
Tot--w,lglodOCC1>-,ndQ,gc>"""-"1 ___ "90,_ , ...
TI RE SIZE CotO TIRE PRESSURE
FRO NT -KPa, - PSI
REAR -KPa, -PSI
Fig. 230 Tire pressure
label
Main taining proper tire pressure is one of the most important
things you can do to help avoid sudden tire failure. Underinflated
tires are a major cause of sudden tire failure. Keeping tires at the
right pressure is also important for safe and responsive vehicle
handling, traction, braking and load carrying.
Tire pressures are
particularly important when the vehicle is being driven at higher
speeds, and then especially when heavily loaded even within the
permissible load-carrying capacities approved for your vehicle.
The recommended tire pressures for your Audi depend on the kind
of tires on your vehicle and the number of passengers and/or
amount of luggage you will be transporting.
On USA vehicles, the tire pressure label is located on the driver's
side B-pillar. On Canada vehicles, the tire pressure label is located
either on the driver's side B-pillar or inside the fuel filler flap . The tire
pressure label lists the recommended cold tire inflation pressures ..,.
Vehicle care I I irechnical data

-~_T_ ir_e_ s_ a_ n_d _ w_ h_ e_e _l_s _________________________________________________ _
for the vehic le at its maximum capacity weight and tires that were
on your veh ic le at the time it was manufactu red .
If you wish to improve comfort when operating the vehicle at
normal load (up to 3 occupants) , you can adjust tire pressures to
those specified for normal vehicle load. Before operating the vehicle at maximum load, you must increase the tire pres sures to those
s pecified for maximum vehicle load =>
&.
Bear in mind that the tire pressure monitoring system* can on ly
m onito r the tir e pres sures you have stored. The sys tem does not
recognize the load condition of your veh ic le.
The effectiveness of the tire p ressure monitoring system* will be
impaired i f you store normal load pressures but then operate the
vehic le at its maximum load=>&. See
the illustrat ion=>
page 291, fig. 229 for the location of the label
ei ther on d river's s id e B-p illar or ins ide the fuel fille r fl ap (c olor of
the actual label and exact location on the vehicle w ill vary sl ight ly).
N ote that the fol lowing tab le is accurate at the time of going to
press and is subject to cha nge . In the eve nt of d iscrepa nc ies, t he tire
pressure label (On USA vehic les, the tire press ure labe l is located on
t he drive r's sid e B- pilla r. On Ca nada ve hicles, the tir e pressu re label
is located either on the driver's side B-pillar or inside the fuel fil ler
fl ap) always takes prece den ce.
T he tab le below l ists the recommended cold tire inflation pressures
f o r the A udi m odel co vered by your Owner's Litera ture at the
veh ic le 's capacity we ight and the ti re s izes installed on t he respec ­
tive mode ls as o rigi nal eq uipment, o r as a facto ry opti on.
Engine Tire designation Tire pressure front Tire pressure rear
(displace- normal load normal load
ment in condition (up to full load
condition (up full load
liter)
condition condition 2 occupants) to 2 occupants)
PSI PSI kPA kPA
4-cylinder 225/50 R17 94H All Season
32 2 20 33 23 0 29 200 33 230
2 .0
245/45 R17 95H All Season 32 220 33 230 29 200 33 230
245/40 R18 93H All Season 33 230
35 240 29 20
0 35 24 0
255 /35 R19 96V XL High Performance
32 220 33 230 32 220 33 230
265 /30 R20 94V XL High Performance 30 210 3 3 230 29 200 33 2 30
& -cylinder 225 /50 R17 94H All Season
33 230 35 240 29 200
33 230
3 .2
245/45 R17 95H All Season
33 230 35 240
29 200 33 230
245 /40 R18 93H All Season 33 230 36 250 29 200 35 240
255/35 R19 96V XL High Performance 32 220
35 24
0 32 22 0 33 23 0
265 /30 R20 94V XL High Performance
30 2
10
33 230 29 200 33 230
XL
= reinforced or extra load tire . It may also appear as xi , EXTRA LOAD, or RF on the tire sidewall.

__________________________________________________ T_ ir_e_ s_ a_ n_d _ w_ h_ e_ e_l_s __ l9III
•
T he correct tire pressure for the spare wheel is located on a label
either on the driver's side B -pi llar or inside the fuel filler flap.
Because technical changes may be made to vehicle equipment
during the mode l year, always compare the tire size designation on
the tire pressure label on your vehicle with the tires on your vehicle. Make sure that the tire size information on the vehicle labe l is the
same as the size of the tires on the vehicle. This is especially impor­
tant if the vehicle belongs to someone else or you bought the
vehic le with different rims/tires or you bought the vehicle as a previ ­
ously owned vehicle.
Remember, your safety and that of your passengers a lso depends
on making sure that load l imits are not exceeded. Vehicle load
includes everybody and everything in and on the vehicle . These load
limits are techn ically referred to as the vehicle's Gross Veh icle
Weight Rating ("GVWR"l. The Gross Axle Weight Rating ("GAWR"l is
the maximum load that can be applied at each of the vehicle's two axles. The Gross Vehicle Weight Rating and the Gross Axle Weight
Rating are l is ted on t he safety compliance sticker labe l located
either on the driver's side B-pillar or on the inside of the fuel fi ller
flap. The ti re pressure labe l on your Audi lists the maximum
combined weight of a ll of the occupants and luggage or other cargo
t hat the vehic le can carry. For the location of the tire pressure label
=>
page 291, fig. 229.
& WARNING
O verl oad ing a vehi cle can c ause lo ss of vehi cle co ntrol , a cras h or
other ac cident , seriou s per sonal injur y, and even death .
• Carry ing m ore w eight t han yo ur vehic le was designed t o carry
will p revent the vehicle from ha ndling properl y and increa se the
ri sk o f a loss of vehi cle co ntrol.
• The br ake s on a ve hicle tha t has been o verloaded may not be
a bl e to st op the veh icle with in a sa fe di stan ce .
• Tires o n a veh icle th at ha s been ov erlo aded ca n fail sudd enl y
ca usin g l oss of co ntrol an d a c rash.
& WARN ING (c ontinued )
• Always m ake sure that the total load being tr ansported -
in cluding the weight of a trailer hitch and the t ongue we ight of a
loaded trailer -do es not m ake the vehicle he avier tha n th e
v ehi cle's Gr oss Vehi cle Weight R ating .
& WARNING
• In corre ct t ire pre ssure s an d/o r underi nfl atio n can lead to a
s eriou s or fatal a ccident.
• In corre ct tire pr essures and/or u nde rin fla tion cau se in cre as ed
tire wear and can affect th e handlin g of the vehicl e.
• Inc orre ct t ir e pre ssu res and /or underinfl ation can a ls o l ead to
s udden tire failure , including a blowout and sudden d eflation ,
ca usi ng loss of vehi cle contr ol. •
Checking tire pressure
The correct tire pressure for the tires originally installed
on your vehicle is listed on the tire pressure label located
either on driver's side B-pillar or inside the fuel filler flap .
The recommended tire pressures are on the ti re pressure label and
in the table=>
page 291, "Cold tire inflation pressure".This means
that the pressure must be checked and adjusted when the tire has
not been driven for more than a couple of mi les (kilometers) at low
speeds during the previous three hours. Air in the tires expands
when the tire heats up as a result of internal friction as i t flexes in
use. The tire pressure is higher when the tire has warmed up than
when it is "cold ."
It is the inflation pressure in a "cold" tire that counts. Therefore, you
should never let air out of a warm tire to match "Co ld tire inf lation
pressure" recommendations=>
page 291. The tires wou ld then be
underinflated and could fail suddenly. .,_
Vehicle care I t •