clock AUDI A5 COUPE 2010 Owners Manual

Instruments and warning/indicator lights
Switching on time, date, temperature display, and
odometer
The display appears for approximately 30 seconds when you press
the !SET] button =>
page 9, fig. 3 with the ignition off.
Starting the Auto-Check sequence
The Auto -Check system => page 27 constantly monitors certain indi­
vidual functions and components of the vehicle when the ignition is
turned on and when the vehicle is moving.
With the ignition turned on, you can start the "Auto-Check
sequence" by pressing the !SET ] button . You can perform an Auto ­
Check sequence when the vehicle is stationary and the ignition is
turned on or when the vehicle is moving slower than 3 mph (5 km/hl.
Calling up the driver information
A yellow or red symbol appears in the instrument cluster display,
usually with a driver message. The driver message display disap­
pears after about 5 seconds. The driver message can be displayed
again by briefly pressing the !SET] button.
Setting the speed warning
By pressing the [SET] button briefly, you can set threshold 1 of the
speed warning while you are driving=>
page 26. By maintaining
pressure on the !SET] button, you delete the warning threshold. •
Digital clock with date display
Digital clock
Fig. 4 Instrument
cluster: time and date
The date, time of day, time and date format can be set in the radio
or MMI*. You can learn more about this in the MMI manual or in the
radio user's manual.
[ i] Tips
• The digital clock turns on for about 30 seconds when the driver's
door is opened.
• When the ignition is turned off, the odometer reading and the
digital clock with date display can be switched on for about
30 seconds by pressing the !SET] button =>
page 9, fig. 3. •
Fuel gauge
The fuel gauge works only when the ignition is on.
When the needle reaches the red area, the warning light in the
instrument cluster will illuminate=>
page 35 . This means you
have approximately 2.1 gallons (8 liters) of fuel left in the tank.
Time
to refuel!
The total tank capacity of your vehicle is listed in=> page 337. .,,

----------------------------------------------~O~n~t:!..h~ e:...!.:ro~a~d!._ _J-
On the road
Steering
Manually adjustable steering wheel
The height and reach of the steering wheel can be
adjusted.
First, adj ust t he drive r's seat correct ly.
F ig . 116 L ev er unde r
th e steeri ng col umn
- Pull the lever~ fig . 11 6 -A rrow- ~ /n..
- Move the steering wheel to the desired position.
Push the lever against the steering column until it locks.
T here must be at l east 10 inches (25 cm) between your chest and the
center of the steering wheel. If you cannot sit more than 10 inches
(25 cm) from the steering wheel, see if adaptive equipment is avail­
able to help you reach the pedals and increase the distance from the
steering wheel.
F or detailed information on how to ad just the driver's seat, see
=> page 72.
Con tro ls and eq uip­
ment
The steering wheel can be adjusted even when the ignition is turned
off. For vehicles with seat memory, the individual positions for the
steering whee l can be stored along with the seat position.
& WARNING
Improper u se of ste ering wheel adju stme nt and improper se ating
po sition can cau se seriou s per sonal injury .
• Adju st the steering wheel column onl y when the vehi cle is not
moving to preven t los s of vehicl e control.
• Adjust the dr iver' s se at or steering wheel so that there is a
minimum of 10 inch es (25 cm ) b etwe en your che st and the
s tee ring wheel
=> pag e 170 , fig. 1 8 0. If you cannot maintain th is
minimum di stance, the airbag sy ste m cannot protect you prop ­
erly .
• If physical limitation s prevent you from sitting 1 O inche s (25
c m ) or mo re from the steering whee l, check with your authori zed
Audi dealer t o see if adaptive equipment i s available .
• If the stee ring whe el i s a ligned with you r fa ce, the supple ­
men tal driver' s airbag cannot provide as much prot ect ion in an
a c cident . A lw ays m ake sure that the steering wheel i s aligned with
your chest .
• Alway s hold t he steer ing wheel with yo ur h and s at the 9 o'c lock
a nd 3 o'clock po sition s to reduce the ri sk of per son al injury if the
dri ver' s airb ag dep lo ys .
• Neve r hold the steering wheel at the 12 o'clock po siti on or with
your hand s insid e the steeri ng wheel rim or on the steer ing wheel
hub. H olding the steerin g wheel th e wrong way can cause seri ous
i nj urie s to the h ands , arm s and head if the dr iver' s a irbag
deploy s.•
Vehicle care
I I irechnical data

___ D_ ri_v _i_n -=g=--- S_ a_ f _e___, ly'---------------------------------------------------
Proper occupant seating positi ·ons
Proper seating position for the driver
The proper driver seating position is important for safe,
relaxed driving.
Fig. 180 The correct
distance between
driver and steering
wheel
Fig. 181 Correct head
restraint position for
driver
For your own safety and to reduce the risk of injury in the
event of an accident, we recommend that you adjust the
driver's seat to the following position:
- Adjust the driver's seat so that you can easily push the
pedals all the way to the floor while keeping your knee(s)
slightly bent=:>& . - Adjust the angle of the seatback so that it is in an upright
position so that your back comes in full contact with it
when you drive.
- Adjust the steering wheel so that there is a distance of at
least 10 inches (25 cm) between the steering wheel and
your breast bone=:> fig. 180. If not possible, see your
authorized Audi dealer about adaptive equipment.
- Adjust the steering wheel so that the steering wheel and
airbag cover points at your chest and not at your face.
- Grasp the top of the steering wheel with your elbow(s)
slightly bent.
- Adjust the head restraint so that the upper edge is as even with the top of your head as possible but no lower
than eye level and so that it is as close to the back of your
head as possible =:> fig. 181.
- Fasten and wear safety belts correctly=:>
page 183.
- Always keep both feet in the footwell so that you are in
control of the vehicle at all times.
For detailed information on how to adjust the driver's seat, see
=> page 72.
& WARNING
Drivers who are unbelted, out of position or too close to the airbag
can be seriously injured by an airbag as it unfolds. To help reduce
the risk of serious personal injury:
• Always adjust the driver's seat and the steering wheel so that
there are at least 10 inches
125 cm) between your breastbone and
the steering wheel.
• Always hold the steering wheel on the outside of the steering
wheel rim with your hands at the 9 o'clock and 3 o'clock positions ..

Driving Safely -
----------------
& WARNING (continued)
to help reduce the risk of personal injury if the driver's airbag
inflates.
• Never hold the steering wheel at the 12 o'clock position or with
your hands at other positions inside the steering wheel rim or on
the steering wheel hub . Holding the steering wheel the wrong way
can cause serious injuries to the hands, arms and head if the
driver's airbag deploys .
• Pointing the steering wheel toward your face decreases the
ability of the supplemental driver's airbag to protect you in a colli­
sion.
• Always sit in an upright position and never lean against or
place any part of your body too close to the area where the airbags
are located .
• Before driving, always adjust the front seats and head
restraints properly and make sure that all passengers are properly
restrained.
• Never adjust the seats while the vehicle is moving. Your seat
may move unexpectedly and you could lose control of the vehicle.
• Never drive with the backrest reclined or tilted far back! The
farther the backrests are tilted back, the greater the risk of injury
due to incorrect positioning of the safety belt and improper
seating position.
• Children must always ride in child safety seats
=> page 213.
Special precautions apply when installing a child safety seat on
the front passenger seat
=> page 188 . •
Controls and equip­
ment Safety first Vehicle operation
Proper seating position for the front
passenger
The proper front passenger seating position is important
for safe, relaxed driving.
For your own safety and to reduce the risk of injury in the
event of an accident, we recommend that you adjust the
seat for the front passenger to the following pos ition:
- Move the front passenger seat back as far as possible.
There must be a minimum of 10 inches (25 cm) between
the breastbone and the instrument panel
=> &.
- Adjust the angle of the seatback so that it is in an upright
position and your back comes in full contact with it
whenever the vehicle is moving.
- Adjust the head restraint so that the upper edge is as
even with the top of your head as possible but not lower
than eye level and so that it is as close to the back of your
head as possible .
- Keep both feet flat on the floor in front of the front
passenger seat.
- Fasten and wear safety belts correctly =>
page 183.
For detailed information on how to adjust the front passenger's
seat, see
=> page 69.
& WARNING
Front seat passengers who are unbelted, out of position or too
close to the airbag can be seriously injured or killed by the airbag
as it unfolds. To help reduce the risk of serious personal injury : .,
Vehicle care Do-it-yourself service Technical data

Fuel supply and filling your fuel tank Refuelling procedure
- Insert the fuel nozzle from the gasoline pump into the
fuel filler neck as far as it will go.
- Select a medium refuelling rate so that the nozzle switches off automatically when the tank is full.
Putting the fuel cap back on
- After filling your tank, twist the fuel cap clockwise as far
as it will go.
- Close the fuel filler flap.
To avoid fuel spilling or evaporating from the fuel tank always close
fuel cap properly and completely.
& WARNING
Improper refueling or handling of fuel can cause fire, explosion
and severe burns.
• Fuel is highly flammable and can cause severe burns and other
injuries.
• Failure to shut the engine off while refueling and/or to insert
the pump nozzle fully into the fuel filler neck could cause fuel to
spray out of filler neck or to overflow. Fuel spray and overflowing
fuel can cause a fire.
• Never use a cellular telephone while refueling. The electromag­
netic radiation can cause sparks that can ignite fuel vapors and
cause a fire.
• Never get back into your vehicle while refueling. If in excep­
tional circumstances you must get back in your vehicle while refu­ eling, make certain that you close the door and touch metal to
discharge static electricity before touching the filler nozzle again.
Static electricity can cause sparks that can ignite fuel vapors
released during refueling.
& WARNING (continued)
• Never smoke or have an open flame anywhere in or near your
vehicle when refueling or filling a portable fuel container.
• For your safety, we strongly recommend that you do not travel
with a portable fuel container in your vehicle. The container, full or
empty may leak and could cause a fire, especially in a crash.
• If, under exceptional circumstances, you must transport a
portable fuel container, please observe the following:
-Never fill a portable fuel container while it is anywhere in or
on the vehicle (for example, in the luggage compartment, or on
the trunk). Static electricity can build up while filling and can
ignite fuel vapors causing a fire.
- Always place a portable fuel container on the ground before
filling.
- Always keep the filler nozzle completely inside the portable
container before and during filling.
- If filling a portable container made of metal, the filler nozzle
must always be in contact with the container. This will help
prevent static electricity from discharging and cause a fire.
- Never spill fuel inside the vehicle or luggage compartment. Fuel vapors are highly flammable .
- Always observe local and state/provincial laws regarding the
use, storage and transportation of fuel containers.
- Make certain the fuel container meets industry standards
(ANSI / ASTM F852-86l.
0 Note
If any fuel has spilled onto the car, it should be removed immedi -
ately to prevent damage to the paint. _.,

___________________________________________ C_ h_e _c_ k_ i_n _g _ a_n _d_ f_il _li _n _g __ ll'I
•
& WARNING
The cooling sy stem i s under pre ssure and can get very hot . Redu ce
the risk of scalding from hot coolant by following these steps.
• Turn off the engine and allow it to cool down .
• Protect your face, hands and arms from escaping fluid and
ste am by cover ing the cap with a large , thick rag .
• Turn the cap slowly and very carefully
in a counter -clockwise
dire ction while applying light , downward pressure on the top of
the cap .
• To avoid being burned, do not spill antifreeze or coolant on the
e x haust system or hot engine parts . Under certain conditions, the
ethylene glycol in engine coolant can catch fire .
0 Note
Do not add any type of radiator leak sea lant to your vehicle's engine
coolant. Adding radia to r repa ir flu id may advers ely affect the fu nc­
tion and performance of your coo ling system and could res ult in
damage not covered by y our New Vehic le Lim ited War ra nty .•
Adding coolant
B e very care ful when ad ding e ngine cool ant.
Be for e you check a nything in the engine com partmen t,
always read and heed all WARNINGS~ & in "Work ing in
t h e eng ine compa rtment" on
page 271 .
-Tur n o ff th e en gine.
- Let the e ng in e cool d own.
- Plac e a thi ck rag over the coo la nt expansion tank
~ page 2 78 , fig. 2 25 and carefully tur n t he cap coun te r­
cl ockwi se
~ &.
Add coo lan t.
- Twist the cap on aga in
tightly.
Replacement engine coolant must conform to exact specifications
~ page 2 77, "C oolant". Even in an eme rgency, if co olant addi tive
G12+ +, G12 + or G12 is not availab le, do not use a different additive.
U se pla in water ins tead until you can ge t the c orrect add itive and
can res tore the correc t rat io. Th is shou ld be done as soon as
p os sible.
I f y ou hav e los t a co ns ide rab le amou nt of coo la nt, then y ou should
add cold antifreeze and cold water only when the engine is cold .
A lways use
new e ngine c oolant w he n r efil ling .
D o not fill coolant a bove the " MAX" mark. Excess coola nt w il l be
forced out through the pressure relief va lve in the cap when the
eng ine becomes hot.
& WARNING
• The cooling system is under pressure and can get very hot .
Reduce the risk of scalding from hot coolant by following these
steps.
-Turn off the engine and allow it to cool down .
- Protect your face , hands and arms from escaping fluid and
steam by covering the cap with a large , thick rag .
- Turn the cap slowly and very carefully in a counter -clockwise
direction while applying light, downward pressure on the top
of the cap.
- To avoid being burned, do not spill antifreeze or coolant on
the exhau st system or hot engine parts. Under certain condi ­
tions, the ethylene glycol in eng ine coolant can catch fire .
• Antifreeze is poisonous. Always store antifreeze in its original
container and well out of the reach of children .
• If you dra in the coolant , it must be caught and safely stored in
a proper container clearly marked "poison ".
~
Vehicle care I t •

-~_T_ ir_e_ s_ a_ n_d _ w_ h_ e_e _l_s _________________________________________________ _
The tire pressure label on your Audi lists the recommended cold tire
in flation pressures at maximum capacity for the new, origina l equip ­
ment tires that were on your vehicle at the time it was manufac­
tured. For the location of the label
~ page 291, fig. 229 .
Most tires lose air natural ly over time. They can a lso lose some air if
you drive over a pothole or hit a curb while parking. It is usually not
possible to see whether the radial t ires used today are underinflated
just by looking at them.
Therefore, be sure to check tire pressures at least once a month and always before going on a long trip. Make sure to take the number of
people and the amount of luggage into account when adjusting tire
pressure for a trip - even one that you would not consider to be
"long ." See ~
page 295, "Tires and vehicle load limits" for more
important information .
Always use an accurate tire pressure gauge when checking and adjusting inflation pressures. Check a ll of the tires and be sure not
to forget the spare tire . If the pressure in any tire is too high when
the tire is "cold," let air out of the tire s lowly with the edge of the tire
gauge and keep checking the pressure until you reach the pressure
that is correct for the load (passengers and luggage) and kind of
driving you p lan to do.
If the pressure in any tire is too low, note the difference between the
press ure in the cold t ire and the pressure you need and add the air
that you need to reach the correct pressure for the vehicle load
(passengers and luggage) for the tires on your vehicle as listed on
the on your vehicle and in this manual and the kind of driving you p lan to do .
Nev er e xce ed the m aximum i nflation pr essure listed on the tir e
s ide wall for any re aso n .
Reme mber that the veh ic le manufacturer, not the tire manufacturer,
determines the correct tire pressure for the tires on your vehicle .
It is important to check the tire pressure when the tires are cold.
• Read the required tire pressure from the tire pressure label. On
USA vehicles, the tire pressure label is located on the driver's side 8-pillar
. On Canada vehicles , the tire pressure label is located either
on the driver's side B -pi llar or inside the fuel fi ller flap . The ti re pres ­
sure labe l lists the recommended co ld tire inflation pressures for
the vehicle at its maximum capacity weight and the tires that were
on your vehicle at the time it was manufactured . For recommended
tire p ressu res for normal load conditions, please see chapter
=> page 291.
• Turn the va lve stem cap counte r-clockwise to remove it from the
tire valve.
• Place the air pressure gauge on the valve.
• T he tire pressures should only be checked and adjusted when
the tires are co ld . The s lightly raised pressures of warm tires must
not be reduced .
• Adjust the tire pressure to the load you are carrying.
• Reinstal l the valve stem cap on the valve.
Wh en should I ch ec k th e tir e pr ess ure?
The correct tire pressure is especially important at high speeds. The
pressure should therefore be checked at least once a month and
a lways before starting a journey . Do not forget to check the tire pres ­
sure for the spare wheel.
When should I adjust the tire p res sure s?
Adjust the tire pressure to the load you are carrying . After changing
a wheel
or replacing whee ls you have to adjust the tire pressu res on
a ll wheels . In addition, you must then initialize the new t ire pres­
sures in the tire pressure monitoring system*~
page 307.
& WARNING
Incorrect tire pre ssur es a nd/or und erinflat ion can lead sudden t ire
fa ilure , loss of cont rol , co llision , seri ous person al inj ury or e ven
death.
• When the w arning symbol
f) a ppe ars in the in strument
cluste r, stop and inspe ct th e tires .

What do I do now ? 1111
------------------
Loosening and tightening the wheel bolts
The wheel bolts must be loosened before raising the
vehicle .
Loosening
Fig . 242 C han ging a
wh eel: l oose ning th e
whee l bolts
- Install the wheel bolt wren ch over the w heel bol t an d
push it d own as far as i t will go.
Take tight hold of the
end o f the w rench ha ndle and turn
the wheel bolts
c ounter- clockwi se about one single turn
in the di rection of arrow=::, fig . 242.
Tightening
- Install the wheel bolt wren ch over the w heel bolt and
push it down as far as it will go.
- Take tight hold of the
end of the wrench han dle and turn
each wheel bolt
clockwise until it is seated .
& WARNING
• Do not use for ce or hu rry when ch ang ing a whee l - you can
ca use th e vehicle t o slip off th e jack a nd cause ser ious p erso nal
inj urie s.
& W ARNING (continued )
• Do n ot loo sen the wh eel bolt s more than one turn before y ou
rais e the vehicle with the jack . - You ri sk an injur y.
[ i ] Tip s
• Never use the hexagona l socket in the handle of the screwdriver
to loosen or tighten the wheel bolts .
• If a wheel bolt is
very tight, you may find it easier to loosen by
carefully pushing down on the end of the whee l bolt wrench with
one foot only . As you do so , hold on to the car to keep your balance
and take care not to slip. •
Raising the vehicle
The vehicle must be lifted with the jack first before the
wheel can be removed .
Vehicle care
Fig. 243 Cha nging a
w he el: m oun ting
poi nts for the jack ..
Do-it-yourself service irechnical data

_____________________________________________ W_ h_ a_t _d_ o_l _ d_o _ n_o_ w_ ? _ __._
Taking the wheel off /installing the spare tire
Follow these instructions step -by-step for changing the
wheel.
Fig . 245 Changing a
wheel: using the screwdriver handle
!with the blade
removed) to turn the
bolts
Fig . 246 Changing a
wheel: alignment pin
inside the top hole
After you have loosened all wheel bolts and raised the
vehicle off the ground, remove and replace the wheel as
follows:
Removing the wheel
-Remove the topmost wheel bolt completely with the
hexagonal socket in the screwdriver handle (vehicle tool
kit) => fig. 245 and set it aside on a
clean surface. - Screw the threaded end of the
alignment pin from the
tool kit hand-tight into the empty bolt hole=> fig. 246.
- Then remove the other wheel bolts as described above.
- Take off the wheel leaving the alignment pin in the bolt
hole.
Putting on the inflatable spare tire
- Push the spare tire over the alignment pin.
- Screw on t he wheel bolts and tighten them
slightly using
the hexagonal socket.
- Remove the alignment pin and insert and tighten the
remaining wheel bo lt slightly l ike the rest.
- Turn the jack handle counter -clockwise to lower the
vehicle until the jack is fully released .
- Use the wheel bolt wrench to tighten all wheel bolts
firmly =>
page 315. Tighten them Tighten them in a criss­
cross pattern ,
from one bolt to the (approximately) oppo­
site one, to keep the wheel centered.
- Perform the steps required after changing the wheel
=>
page 313, "After changing a wheel".
The hexagonal socket makes it easier to remove the wheel bolts
from the rim . Care should be taken when removing the reversible
blade.
[ i] Tips
• When mounting tires wi th unidirectional tread design make sure
the tread pattern is pointed the right way~
page 318.
• The wheel bolts should be clean and easy to turn. Check for dirt
and corrosion on the mating surfaces of both the wheel and the .,
Vehicle care Do-it-yourself service irechnical data

llffl __ A_l.:. p _h_ a_ b_e _t _ic _ a_l _in _ d_e _x ____________________________________________ _
Care of exterior ... .. ... ... ... ... ... . 252
Cargo area
See Loading the luggage compartment ..
175
Cargo net .... .... ................... 79
Catalytic converter . . . . . . . . . . . . . . . . . . 244
Center armrest Adjusting ........................ 78
Storage compartment ........ .... . 78
Certification . . . . . . . . . . . . . . . . . . . . . . . 342
Changing a flat tire .. .... .... ....... 312
Changing a wheel ................... 312
Changing engine oi l ...... .... .... ... 276
Chassis Undercoating . . . . . . . . . . . . . . . . . . . . 258
Checking Engine coolant level .. ...... ...... 278
Checking tire pressure .... .... .... ... 293
Child restraint system anchors ........ 227
Child restraints Danger of using child restraints in the
front seat . . . . . . . . . . . . . . . . . . . . . . 190
Where can I get additional information
about child restraints and their use? ...
232
Child safety ................... .... . 213
Convertible locking retractor . . . . . . . 223
Important safety instructions for using
child safety seats .... .... ... .... 216
Important things to know when driving with chi ldren ................... 213
Installing a child restraint using the
LATCH system .................. 229 Lower
anchorages ... ...... ...... . 228
Mounting and releasing the anchorage hook .. .............. ....... ... 229
Tether anchors .. ...... .... .... .. 230
Tether straps ........ ....... ..... 230
Child safety seats ... ........... ..... 218
Booster seats .. ... .... ........ ... 221
Convertible chi ld seats ............ 219
Convertible locking retractor . ...... 223
Danger of using child restraints in the
front seat . . . . . . . . . . . . . . . . . . . . . . 190
How do I properly install a child safety
seat in my vehicle? ........ ...... 216
Infant seats ...... ........ ....... 218
Installing ....................... 223
LATCH system . . . . . . . . . . . . . . . . . . . 229
Safety instructions .... ...... ..... 216
Cigarette lighter ........ ....... ...... 87
Cleaning Alcantara® (synthetic suede) . ..... 262
Engine compartment ....... ... ... 263
Fabrics and fabric coverings ..... .. 259
Instrument panel ................. 260
Interior .. .... .... ... .. .... .... .. 259
Leather ......................... 261
MMI display ..................... 259
MM I termina l .. ... .... .... .... ... 259
Plastic and vinyl .. .. ......... ... . 256
Plastic parts . . . . . . . . . . . . . . . . . . . . . 260
Safety be lts ...... ....... ........ 263
Trim strips . ........... .... ...... 255
trim strips ... .. ........ .... ... ... 256
Cleaning and protection .. ........ ... 252
Clock ........ .... ...... ....... ...... 10 Coat hooks
. . . . . . . . . . . . . . . . . . . . . . . . . . 89
Co ld tire inflation pressure .... ....... 291
Compact spare tire .................. 311
See also Spare tire ........ ...... .. 311
Compass mirror . ...... .. .... .... .... 67
Comp liance ...... .... ....... .... ... 342
Consumer Information .... ... ... . 177, 339
Contacting NHTSA ... .... .... .... ... 177
Convenience closed ... ....... ........ 49
Convenience key ..................... 44
START ENGINE STOP button ... 110, 111
Starting engine .... ....... .... ... 110
Switching engine off .............. 111
Switching on ignition ............. 11
O
Unlocking and locking vehicle ... ... . 44
Convenience opening ...... ........... 49
Convertible child safety seats ...... ... 219
Convertible locking retractor Activating .. ....... .... ...... .... 225
Deactivating ..................... 226
Using to secure a child safety seat .. 223,
225
Coolant system ..................... 277
Cooling System Expansion tank .... ........... ... 278
Cornering light ...................... 57
Cruise contro l
Changing speed . ...... .... .... .. 116
Preselect speed .. ...... ..... .. ... 116
Switching off ... .. .... .... .... ... 116
Switching on ...... ........... ... 115
Warning/indicator lights ... .. ...... . 15
Cruising range ................... .... 23