light AUDI A5 COUPE 2014 Owner's Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2014, Model line: A5 COUPE, Model: AUDI A5 COUPE 2014Pages: 286, PDF Size: 70.99 MB
Page 32 of 286

30 Driver information display
Resetting the service interval display
Your authorized Audi dealer will reset the corÂ
responding service schedule after performing
the appropriate service on yo ur vehicle . Yo u
also have the possibility to reset the oil
change schedule after having performed an
oil change according to Audi specifications.
Select
I CAR I function button > Service interval
display > Reset oil change interval
or ICARI
function button> Car systems* control butÂ
ton
> Servicing & checks > Reset oil change
interval.
(D Note
If you disconnect the battery terminals, no
calculations can be made for the serv ice
interval display during this time and no
service rem inder wi ll appear. Remember
that observing the proper service intervals
is vitally important to extend ing the life of
your vehicle, particu larly the eng ine, and
maintaining its value. Even if the mileage
driven is low, the maximum period of one
yea r from one service to the next must not
be exceeded .
@ Tips
-Do not reset the display between oil
changes, otherwise the display will be inÂ
correct.
- The information in the Service Reminder
r ema ins stored even when the vehicle
battery is disconnected.
On-Board Diagnostic
system (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) ¢4' i n
the instrument cluster is part of the On-Board
Diagnostic (OBD II) system.
The warning/indicator light illuminates when
the ignition is switched on and goes out after
the engine starts and the idle has stabilized .
This indicates that the MIL is working properÂ
ly.
If the light does not go out after the engine
is started, or illuminates while you are drivÂ
i ng, a malfunction may exist in the eng ine sysÂ
tem . If the light illuminates, the catalytic conÂ
verter could be damaged .
Continue driving
with reduced power (avoidÂ
ing sustained high speeds and/or rapid accelÂ
erations) and have the cond ition corrected.
Contact your authorized Audi dealer.
If the light il luminates, the electronic speed
limiter may also be malfunct ioning. For more
information
c:> page 31 , Electronic speed
limiter.
An improperly closed fuel filler cap may also
cause the
MIL light to illuminate
c:>page 204.
On-Board Diagnostics
Fig . 18 Locat io n of Data Link Con nector (D LC)
On-Board Diagnostics monitors the compo Â
nents of your emission control system . Each
monitored component in your engine system
has been assigned a code. In case of a malÂ
function, the component will be identified
and the fault stored as a code in the control
module memory.
The MIL light may also illuminate if there is a leak in the on-board fuel vapor recovery sysÂ
tem. If the light illuminates after a refueling,
stop the vehicle and make sure the fuel filler
cap is properly closed
c:> page 204.
In order to make an accurate diagnosis, the
stored data can on ly be displayed using speÂ
c ial diagnostic equipment (generic scan tool
furOBD) .
~
Page 33 of 286

In o rder to connect the special diagnostic
equipment, push the plug into the Data Link
Connector (DLC) . The DLC is located to the
right of the hood release ¢
fig. 18.
Your authorized A udi dealer or qualified workÂ
shop can interpret the code and perform the necessary repa ir.
A WARNING
Do not use the diagnostic connector for
personal use. Incorrect usage can cause
malfunctions, which can increase the risk
of a coll is ion!
Electronic speed limiter
-
Your veh icle may be factory equipped with
tires that are rated for a maximum speed of 130 mph (210 km/ h). Thi s is may be less than
the maximum speed of your ve hicle. To red uce
the risk of sudden ti re failure and loss of con Â
trol if the vehicle is operated at excessive
speeds, your vehicle has an e lectronic speed
limiter. The electronic speed limiter prevents
your veh icle from going faster than the t ire
speed rat ing . For more informat ion
¢ page 233 .
If the engine control unit rece ives fa ulty vehi Â
cle roadspeed signa ls, the Ma lfunction IndicaÂ
tor Light (MIL)
¢4 will illuminate . If this ocÂ
curs, contact the nearest authorized Audi
deale r for assistance.
A WARNING
-
Always observe the posted speed limits
and ad just yo ur speed to suit p revail ing
road, traff ic and weather conditions . Never
drive your vehicle faster than the maxi Â
mum speed rating of the tires insta lled .
Dri ver information di spla y 31
Page 36 of 286

34 Openin g and clo sing
keys. Unguarded access to the keys proÂ
vides children the opportunity to start the engine and/or act ivate vehicle sysÂ
tems such as the power w indows etc . UnÂ
supervised operation of any veh icle sysÂ
tem by ch ildren can res ult in serious inÂ
Jury.
- Do not remove the key from the ignition
lock until the vehicle has come to a comÂ
plete stop. Otherwise the steering colÂ
um n loc k co uld suddenly e ngage -causÂ
ing the risk of an accident.
@ Tips
- The operation of the remote contro l key
c a n be tempo rarily disrupted by in terferÂ
ence from tran smi tters in t he v ici nity of
the veh icle work ing in the same frequenÂ
cy ra nge (e.g . a ce ll phone, radio equipÂ
ment).
- Fo r security reasons, replacement keys
are on ly available from author ized Audi
dealer.
- For Decla ration of Compliance to United
States FCC and Industry Canada regu laÂ
tions
c:> page 267.
Removing the mechanical key
Fi g. 20 Rem ote ma ste r ke y: remov ing the mec hanic al
key
" Press the release button ® c:> fig. 20 .
"Pull the mecha nica l key @out of the maste r
key .
Using the mechan ica l key , you can :
- lock and unlock* the glove compartment on
the passenger's sid er=>
page 60.
-lock and unlock the lockab le rear bench seat
and pass-through
r=> page 63 .
-lock and unlock the vehicle manua lly
¢ page 3 7 if this should not be possible
w ith the master key.
- use t he ignition key emergency release
r=> page35.
Check light and battery in the master
key
Fig. 21 Re mote mas ter ke y: r em ov ing th e ba ttery h old Â
e r
Check light in the ma ster key
The check light ®
r=> fig. 21 in the master key
provides information about different condiÂ
t ions.
" The check light turns on br iefly once when a
button is pressed, and during an "inquiry"
by the convenience key system .
"If the check light does not come on, the batÂ
tery is dead and has to be replaced . In addiÂ
tion, when the ba tte ry is dead the
I! indiÂ
ca to r li ght a ppears in the instrument cl uster
d isp lay as well as the message
Plea se
c hange key battery .
Master key battery replacement
" Remove the mechan ica l key
r=> page 34.
" Press the re lease b utton @ r=> fig. 21 on the
b attery ho lde r and at the same time pull the
battery holde r out o f the master key in the
direction of the arrow.
" Insta ll the new battery CR 2032 with the
"+ " sign facing down.
" Push the battery holder carefully into the
master key .
" Insta ll the mechanical key.
Page 39 of 286

- You cannot open the doors or the rear lid
from the
outside (increased security, for exÂ
amp le when you are stopped at a red light).
- The diodes in the power locking switc h illuÂ
minate when all the doors are closed and
locked.
- You can unlock and open the doors from the
i nside by pul ling on the door hand le .
- If you have a crash and the airbag is activat Â
ed , the doors automatically un lock .
_& WARNING
- The power locking switch works with the
ignition off and automatically locks the
entire vehicle when it is actuated .
- On a vehicle locked from the outside the
power locking system switch is inoperaÂ
t ive.
- locked doors make it more difficult for
emergency workers to get into the vehiÂ
cle, which puts lives at risk . Do not leave
anyone behind in the veh icle, especially
children .
@ Tips
Your vehicle is locked automatically at a
speed of 9 mph (15 km/h) (Auto lock)
¢page 32. You can un lock the vehicle
aga in using the opening function in the
powe r locking system switch~-
Setting power locking
In the radio/MM!*, you can set which doors
the centrol locking system will unlock .
~ Select: I CAR I function button > Central lockÂ
ing .
Or
~ Select: ~IC_A_R~I funct ion button> Car systems *
control button > Vehicle settings > (C entral
locking )* .
Sin gle door unlocki ng /Unl ock door s* -
you
can specify which doors u nlock when you open
the vehicle .
- Se lecting
off / All and pressing the Ii button
on the remote control key unlocks the entire
vehicle.
Opening and clo sin g 3 7
- Select ing o n/Dri ver and pressing the~ butÂ
ton on the remote control key once u nlocks
only the driver's door . In vehicles w ith a con Â
ven ience key*, only the door whose handle
you pull w ill unlock . If you press the @! butÂ
ton tw ice, the entire vehicle will u nlock . If
you press the [@] button, t he e ntire ve hicle
w ill always lock .
Luggage comp. lock /Lock e xterio r trunk han Â
dl e -
If you select On , you can no longer open
the luggage compartment us ing the rear lid
hand le ¢
page 39, fig. 28 . In this case, the
r ear lid can be opened with the
l""I bu tton on
the maste r key ¢
poge 35, fig. 22 or with the
l"" I* button in the driver's door ¢ page 39,
fig .
27 .
Ton e when lo cking -if you select On, a tone
will sound when yo u loc k the vehicle .
Auto Lock /Lock when dri ving -if you select
On, the enti re ve hicle w ill lock automatica lly
when the speed reaches 9 mph (15 km/h).
Emergency locking
Fi g. 25 Drive r's doo r: lock cylinde r
Fig. 26 Fro nt passenger 's doo r: emergency lock
If the central lock ing system malfunct ions,
you must unlock/lock the doors separate ly usÂ
ing t he emergency key or the mechanical key .
IJJJ,
Page 41 of 286

Rear lid
Opening/closing rear lid
Fig . 27 Driver"s door: remote rear lid release
Fig. 28 Rear lid: hand le
Op en ing th e rea r lid
.,. Press the button -c:s on the remote contro l
master key for at least one second. The rear
lid unlocks and opens slightly. Or
.,. Pull the release button
-c:s in the driver's
door
q fig. 2 7. Or
.,. Press the handle on the rear lid
¢ fig . 28.
C losi ng th e re ar lid
.,. Pull the rear lid down at the grip on the inÂ
side and allow it to drop gently to close it
¢,&. .
A WARNING
-After closing the rear lid, always pull up
on it to make sure that it is properly
closed. Otherwise it could open sudden ly
when the veh icle is moving.
- To help prevent po isonous exhaust gas
from being d rawn into the vehicle, alÂ
ways keep the rear lid closed while driv ing. Never transport objec ts larger than
those which fit comp letely into the lug -
Openin g an d clos ing 39
gage area, because then the rear lid canÂ
not be fully closed.
- Never leave your vehicle unattended esÂ
pecia lly with the rear lid left open. A
child could craw l into the car through the
luggage compartment and pull the lid
shut, becoming trapped and unable to
get out. To reduce the risk of personal inÂ
jury, never let ch ildren play in or around
your veh icle. Always keep the rear lid as
well as the vehicle doors closed when not in use.
- Always ensure that no one is within
range of the rear lid when it is moving, in
particular close to the hinges -fingers or
hands can be pinched .
@ Tips
When the vehicle is locked, the rea r lid can
be opened separately by pressing the butÂ
ton
-c:s on the master key . When you close
the rear lid aga in, it locks automat ica lly.
Trunk escape handle
In case of an emergency, the luggage comÂ
partment lid can be opened from the inside
using the trunk escape handle .
Fig. 29 Trunk escape handle: view from inside the
closed rear lid
To open lu ggage compartment lid
.,. Pull the handle down towards the bumper
¢fig. 29.
The trunk escape hand le inside the luggage
compartment lid is made of fluorescen t ma te-
rial to glow in the dark. .,..
Page 44 of 286

42 Opening and clo sing
Emergency closing of the panoramic
tilting sunroof
If the sunroof detects an object in its path
when it is closing , it will open again a utomati Â
cally. In this case, you can close the roof with
the power emergency closing function .
.. Within five seconds after the s unroof opens
automatically, pull the switch until the roof
closes .
Valet parking
Applies to vehicles : wit h va let pa rking funct io n
The valet parking feature protects the lugÂ
gage compor tment from unau thorized acÂ
cess .
-
Fig. 3 3 G lo ve co mpa rtm en t: va le t pa rk in g b utton
You can switch the "va let par kin g f unct ion " on
when someone else is park ing yo ur vehicle.
When the function is switc hed on, the vehicle
can be dr iven , locked and unlocked using the
master key, but access to the luggage comÂ
partment is not permitted .
.. Take the mechanical key out of the master
key
c::> page 34 .
.. Open the glove compartment c::> page 60 .
.. Activate c::> fig. 33 th e "valet parking" fea Â
ture by press ing the
!VA LE T ! button . The inÂ
dicator light in the switch illum inates .
.. Close the glove compartment a nd lock it
with the mechan ica l key .
.. Lock both rear seatbacks with the mechaniÂ
c al key
c::> page 63 .
.. Lock the lugg age compa rtmen t pa ss Â
th rough wi th the mechanical key
~ page 65 .
.. Leave the master key w ith the serv ice per Â
sonnel for parking and keep the mechanica l
key with you.
T he following buttons are deactivated when
the va let parking f unction is switched on:
-lar l button in the d river 's doo r
-lar l button on the master key
- Handle in the rear lid
When the valet parking feature is activated,
t h e message
Valet parking activated appears
in the instrumen t clus ter disp lay when you
switch the ign ition on .
Page 45 of 286

Clear vision Lights
Switching the lights on and off
F ig . 34 Instrument pane l: headlight control switch
Light switch ·'t/,·
Turn the switch c> fig. 34 to the correspond ing
position . When the lights are switched on, the
:oo: symbol turns on.
0 • The lights are off or the daytime running
lights are on:
-USA mod els : The daytime running lights are
activated when the light switch
c> fig . 34 is
in the
O position or the AUTO position (only
in daylight conditions) . The daytime running
lights function can be turned on and off in
the radio or MMI* menu
E xterior li ghtin g
¢ page 44 , c> &_.
-Ca nada mod els: The daytime runn ing lights
are activated when the light switch
¢ fig . 34
is i n the O position, :oo : position or the AUTO
posit ion (on ly in daylight cond itions). The
daytime running lights function cannot be
turned off¢&. .
AUTO* -Automatic headlights switch on and
off depending on b rightness, for example in
tw ilight, during rain or in tunnels ¢,& .
:oo: -Side marker lights
~D -Low beam headlights
Fog light s/rear fog ligh t(s)*
Press the appropriate button c> fig. 34:
1D -Fog lights
0$ -Rear fog light(s)
Clear vi sion 43
adaptive light*
When switched on, adaptive ligh t adap ts to
curves in the road depend ing on the vehicle
speed and the steering angle. This provides
better lighting through the curve. The system
operates at speeds between approximately
6 mph (10 km/h) and 68 mph (110 km/h).
Static corner ing light * (vehicles with adaptive
light) -the cornering light switches on at
speeds up to approximately 25 mph (40 km/
h) when a certain steering wheel angle is
reached or when a turn signal is activated. The
area to the s ide of the vehicle is illuminated
better whe n turn ing .
The adaptive light and the cornering light only
function when the switch is in the AUTO posiÂ
tion (automatic headlights*) .
A WARNING
-Daytime running lights and automatic
headlights* are only intended to ass ist
the driver . T hey do no t re lieve the driver
of his responsibility to chec k the head Â
lights and to t urn them on manua lly acÂ
cording to the current light and visibility
conditions. For example, fog cannot be
detected by the light sensors*. So a lways
switch on the headlights
~D under these
weather conditions and when driving in
the dark .
- Cras hes can happen when you cannot see
the road ahead and when yo u cannot be
seen by other motorists. Always turn on
the head lights so that you can see ahead
and so that others can see your car from
the b ack.
- Please obey all laws when using the
lig hting sys tems described here.
(D Note
The rear fog lights* should on ly be turned
on in accordance with t raff ic regulation, as
the lights are bright for following traffic. ..,.
Page 46 of 286

44 Clear vis ion
@ Tips
- The light sensor* for headlight control is
located in the rear view m irror mount.
You should therefore not apply any st ickÂ
ers to the windsh ield in this area in order
to prevent malfunctions or failures.
- Some exterior lighting functions can be
adjusted
c> page 44.
- When you remove your key from the igniÂ
tion while the vehicle's lights are turned
on, a buzzer sounds as long as the drivÂ
er's door is open .
- In cool or damp weather, the ins ide of
the headlights, turn signals and tail lights can fog over due to the temperaÂ
ture difference between the inside and
outside. They will clea r shor tly after
switching them on. This does not affect
the service life of the lighting.
- In the even t of a light sensor malfuncÂ
tion, the driver is no tified in the instruÂ
ment cluster disp lay¢
page 22.
Turn signals and high beam lever
The lever operates the turn signals, the high
beams and the headlight flasher .
Fig. 35 T u rn s ig na l and hig h beam lever
Turn sign als ¢i ¢
The turn signals activate when you move the
l ever into a turn s ignal pos ition when the ign iÂ
tion is switched on.
(D -right turn signal
@-left tur n signa l
The turn s ignal blinks three times if you just
tap the lever .
High be ams and headlight flasher [D
Move the lever to the correspon ding posit io n:
@ -high beams on
@ -high beams off or headlight flasher
The indicator light
ii in the instrument cl usÂ
te r turns on .
Notes on thes e features
-The turn signals on ly wor k w ith the ignition
t ur ned on. The indicator ligh ts
Ct or a in
the instrument cluster also blink.
- After you have turned a co rner, the turn s ig Â
na l switches off au toma tically .
- The
high beam works on ly w hen the headÂ
lights a re on. The ind icator ligh t
II in the
instrument cluster illuminates when the
high beams are on .
- The
headlight flasher works o nly as long as
you ho ld the lever -even if there a re no
lights switched on . The indicator light
II in
the instrument cluster illuminates when you
use the headlight flasher.
A WARNING
--
Do not use the h igh beam or headlight
flasher if you know that these could blind
oncom ing traffic.
Adjusting exterior lighting
The functions ore selected in the radio or
MMI" .
.,. Select: !CARI function button> Exte rior
light ing .
Or
.,. Select: !CARI function button > Car systems *
control button > Vehicle s etting s> Exterior
lighting .
Coming home (light when leav ing car }*,
Leav ing home (light when unlocking car )*
The coming home function illuminates the
area around the vehicle when the ignition is
switched off and th e dr ive r's door is open ed.
Depend ing on veh icle equ ipment, the function
can be switched on and off or the length of
time the lig hts remain on* can be ad justed . ..,.
Page 47 of 286

The leavin g home function il luminates the
area around the vehicle when unlocking it.
This function can be switched on and off.
The
c o ming h om e and lea ving home funcÂ
tions on ly operate when it is dark and the
light switch is in the AUTO position
¢ page 43, fig. 34.
Auto headlight s*
When the light switch is in the A UTO
¢ page 43 position, the switch-on po int of the
lights can be changed in the automatic driving
light function.
Daytime running lights
USA m odel s:
You can switch the dayt ime runÂ
ni ng lights
on and o ff .
Canada mod els:
The function cannot be
turned off .
It is activated a utomat ica lly each
time the ignition is switched on.
Travel mode*
The headlight beam is asymmetrical. This proÂ
v ides stronger illum ination on the side of the
road on wh ich you are driving .
If you are drivÂ
i ng in a count ry that d rives on the opposite
side of the road from your own country, th is
will cau se glare for on coming dr ivers. To preÂ
vent glare:
- Trave l mode must be selected in vehicles
with Xenon headlights*.
- In veh icles with halogen headlights, ce rtain
areas of the head light lenses must be covÂ
ered w ith wate rproof adhesive covers that
prevent light from passing thro ugh. Fo r
more information, please see your author Â
ized Audi dea ler or author ized repa ir faci lity .
(D Tips
When trave l mode is activated, a display in
the dr iver information system indicates
this each time you switch the ignit io n on.
Clear vi sion 45
Emergency flashers
F ig. 36 Center console: emergency flasher switch
The emergency flashers makes other motoÂ
rists aware that you or your vehicle are in an
emergency situation .
.. Press the switch
Gil¢ fig. 36 to turn the
emergency flashers on or off.
When the emergency flas hers are on, all four
turn signals b link at the same time. The turn
s ignal indicator lights .
1B in the instruÂ
ment cluster, as well as the light in the emerÂ
gency flasher switch ~ blink likewise.
You can indicate a lane change or a tu rn w hen
the emergency flashers are switched on by usÂ
ing the turn signal lever. The emergency flashÂ
ers stop temporarily.
T he emergency flashers also work when the
ignition is turned off.
T he emergency flashers w ill turn on a utomat iÂ
ca lly if yo u are in an accident where the airbag
has deployed.
(D Tips
You sho uld turn on the emergency f las hers
when:
- yo u are the last veh icle standing in a t raf Â
fic jam so that any other vehi cles coming
can see you, or whe n
- yo ur vehicle has bro ken down or you are
in an eme rgency s ituation, or when
- yo ur vehicle is be ing towed by a tow
truck or if you are tow ing another vehicle
beh ind you.
Page 48 of 286

46 Clear vis ion
Interior lights
Front /rear interior lights
Fig . 37 Front headliner: inte rior lighting controls
Fig. 38 Rear headliner: rear reading lights
@Interio r ligh ts
Press the switch ~ fig. 3 7 in the correspondÂ
ing position.
0 -Interior lights off
I -Interior lights on
If the switch is in the center position, the inteÂ
rior l ights turn on automatically when you unÂ
lock the vehicle, open a door or remove the igÂ
n ition key. The interior lights turn off several
seconds after your close the doors , when you
lock the vehicle or when you turn the ign it ion
on. When a door is open, the light tu rns off
after a few minutes.
@ Front /rear r eading lights
To turn a reading light on/off, press the butÂ
ton~
~ fig. 37 or ~fig. 38.
The appearance and location of the rear readÂ
ing lights may differ depending on the model.
Instrument illumination
The basic brightness of the illumination for
the instruments, the center console and the
display can be adjusted .
Fig . 39 Inst rume nt illu mination
.,. Press the knob to release it .
.,. Turn the knob toward"-" or"+" to reduce or
increase the brightness .
.,. Press the knob again to return it to its origiÂ
nal posit ion.
(!') Tips
The instrument i llum ination (for dials and
needles) lights on when the ignition is
switched on and the vehicle lights are
turned off . As the daylight fades, the illuÂ
mination of the dia ls likewise dims autoÂ
matically and wi ll go out completely when
the ou tside light is very low. This feature is
meant to rem ind you to sw itch on the
headlights when ou tside light conditions
become poor .
Vision
Adjusting the exterior mirrors
Fig . 4 0 Forward section of driver's armrest: power mirÂ
r or controls